private volatile int sleepTimes = 0;//对休眠次数计数
/// <summary>
/// 处理PLC打包指令，每SENDTOPLC_INTERVAL毫秒发一次，
/// 同一PLC上次与本次间隔为PLC个数*SENDTOPLC_INTERVAL，此值过大，会造成灯指令覆盖
/// </summary>
void HandlePackPLCComm()
{
while (true)
{
try
{
int[] strKey = null;
lock (dicSendWindow)
{
int dicCount = dicSendWindow.Keys.Count;
strKey = new int[dicCount];
dicSendWindow.Keys.CopyTo(strKey, 0);
}
int PLCCount = strKey.Length;
for (int i = 0; i < PLCCount; i++)
{
int key = strKey[i];
PLCCommand command = null;
lock (dicSendWindow)
{
command = dicSendWindow[strKey[i]];
}
if (!command.Send)
{
Interlocked.Add(ref sleepTimes, 1);//加1
WinApi_PLC.SendDataAllOut((byte)key, command.ThirdFrame, command.FourthFrame);
//bl_plc.SendDataAllOut((byte)key, command.ThirdFrame, command.FourthFrame);
command.Send = true;//更新为已发送
lock (dicSendWindow)
{
dicSendWindow[key] = command;
}
//每个包之间都要间隔200毫秒，不然plc接收会粘包，而且plc同地址会中断
Thread.Sleep(SENDTOPLC_INTERVAL);
}
}
//循环结束后，sleepTimes=0;休眠中断间隔，=1休眠剩余时间间隔
if (sleepTimes <= 1)
{
int sleepInterval = PLC_INTERRUPT_INTERVAL - sleepTimes * SENDTOPLC_INTERVAL;
Thread.Sleep(sleepInterval < 0 ? 0 : sleepInterval);
}
Interlocked.Add(ref sleepTimes, -sleepTimes);//0
}
catch (Exception ex)
{
Thread.Sleep(PLC_INTERRUPT_INTERVAL);
InternalLogger.Log.Error("处理PLC打包指令出错：" + ex.Message);
}
}
}
/// <summary>
///打包帧
/// </summary>
/// <param name="command"></param>
/// <param name="lightAddress">从0开始到15</param>
/// <param name="lightStatus"></param>
void SetFrame(PLCCommand command, int lightAddress, byte lightStatus)
{
if (lightAddress >= 0 && lightAddress <= 7)
{
command.ThirdFrame = SetBit(command.ThirdFrame, 8 - lightAddress, lightStatus == 1);//设置第三帧
}
else
{
command.FourthFrame = SetBit(command.FourthFrame, 16 - lightAddress, lightStatus == 1);//设置第四帧
}
}
/// <summary>
/// 打包PLC指令
/// PLC首次，将plc地址保存，将<led地址,发送时刻>保存;指令打包并保存
/// PLC非首次，但LED首次，将指令打包保存
/// PLC非首次且LED非首次，判断间隔是否满足设定；（若满足，将指令打包保存;若不满足，则新线程等待设定时间后，打包保存)
/// </summary>
/// <param name="plcAddress">PLC地址号</param>
/// <param name="lightAddress">PLC控制输出端口号(一般16个)</param>
/// <param name="lightStatus">1开灯，0关灯</param>
/// <param name="lightTime">灯开闭间隔</param>
private void ControlPLCInterval(int plcAddress, int lightAddress, byte lightStatus, int lightTime)
{
try
{
double curTime = (DateTime.Now.ToUniversalTime() - baseDatatime).TotalMilliseconds;
lock (dicSendWindow)
{
PLCCommand command = null;
if (dicSendWindow.ContainsKey(plcAddress))
{
dicSendWindow.TryGetValue(plcAddress, out command);
if (command.DicLightSendTime.ContainsKey(lightAddress))//此灯已发送过
{
double preTime = 0;
command.DicLightSendTime.TryGetValue(lightAddress, out preTime);
double totalTime = curTime - preTime;
if (totalTime < lightTime)//时间间隔小于设定值
{
int sleepReply = (int)Math.Ceiling(lightTime - totalTime);
#region 在sleep前，需把本次的时间戳保存，防止后面还有指令进来
command.DicLightSendTime[lightAddress] = curTime + sleepReply; //更新发送时刻
dicSendWindow[plcAddress] = command; //更新
#endregion
smartThreadPool.QueueWorkItem(() =>
{
//新线程，先sleep（lightTime-totalTime）后，再lock放入dicSendWindow
Thread.Sleep(sleepReply);
lock (dicSendWindow)
{
SetFrame(command, lightAddress, lightStatus);
command.DicLightSendTime[lightAddress] = curTime + sleepReply; //更新发送时刻
command.Send = false;
dicSendWindow[plcAddress] = command; //更新
}
});
return;//直接退出，不要删除
}
else//大于设定间隔
{
command.DicLightSendTime[lightAddress] = curTime;//更新发送时刻
}
}
else//此灯第一次发送
{
command.DicLightSendTime.Add(lightAddress, curTime);//将plc下灯地址发送时刻保存
}
SetFrame(command, lightAddress, lightStatus);
command.Send = false;
dicSendWindow[plcAddress] = command;//更新
}
else
{
command = new PLCCommand(); //command.Send = false;默认
SetFrame(command, lightAddress, lightStatus);
command.DicLightSendTime.Add(lightAddress, curTime); //将plc下灯地址发送时刻保存
dicSendWindow.Add(plcAddress, command); //新增
}
}
}
catch (Exception ex)
{
InternalLogger.Log.Error("打包PLC指令出错：" + ex.Message);
}
}
