/// <summary>
/// 绘制主部件螺栓，采用单独的一道尺寸;
/// </summary>
public void DrawMainPartBoltDimX()
{
PointList pointList = new PointList();
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
//2.判断主梁的螺栓是否需要标注;
bool bNeedMainBeamBoltDim = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrBolt);
if (bNeedMainBeamBoltDim)
{
CMrDimSet mrDimSet = GetMainPartBoltUpDimX();
foreach (Point pt in mrDimSet.GetDimPointList())
{
pointList.Add(pt);
}
if (pointList.Count == 0)
{
return;
}
Point minXPoint = mMainBeam.GetMinXPoint();
Point maxXPoint = mMainBeam.GetMaxXPoint();
pointList.Add(minXPoint);
pointList.Add(maxXPoint);
Vector upDimVector = new Vector(0, 1, 0);
mUpDimDistance = GetUpDimDistance(pointList[0]);
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, mUpDimDistance, CCommonPara.mSizeDimPath);
}
}
/// <summary>
/// 标注工作点到工作点之间的尺寸;
/// </summary>
public void DrawWorkPointToWorkPointDimX()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
PointList pointList = new PointList();
bool bMarkValue = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
mMainBeam.SetNeedAddMarkFlag(bMarkValue);
//1.判断工作点与工作点之间是否需要标注，需要标注的话是一道单尺寸;
bool bNeedDimWpToWp = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
if (bNeedDimWpToWp)
{
Point leftWorkPoint = CMrMainBeam.GetInstance().mLeftWorkPoint;
Point rightWorkPoint = CMrMainBeam.GetInstance().mRightWorkPoint;
pointList.Add(leftWorkPoint);
pointList.Add(rightWorkPoint);
Vector upDimVector = new Vector(0, 1, 0);
mUpDimDistance = GetUpDimDistance(leftWorkPoint);
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, mUpDimDistance, CCommonPara.mMainSizeDimPath);
}
}
/// <summary>
/// 绘制主梁上螺钉的标记;
/// </summary>
public void DrawMainPartBoltMark()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
bool bNeedMark = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrBolt);
if (!bNeedMark)
{
return;
}
List <CMrBoltArray> mrBoltArrayList = mMainBeam.GetBoltArrayList();
Vector zVector = new Vector(0, 0, 1);
DrawingHandler drawingHandler = new DrawingHandler();
TSD.UI.DrawingObjectSelector DS = drawingHandler.GetDrawingObjectSelector();
foreach (CMrBoltArray mrBoltArray in mrBoltArrayList)
{
//只有与Z轴平行的螺钉组才进行编号;
if (!CDimTools.GetInstance().IsTwoVectorParallel(zVector, mrBoltArray.mNormal))
{
continue;
}
DS.SelectObject(mrBoltArray.mBoltInDrawing);
}
CDimTools.GetInstance().DrawMarkByMacro();
}
/// <summary>
/// 标注切割的尺寸;
/// </summary>
public void DrawCuttingDim()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
PointList pointList = new PointList();
//判断是否需要标注切割部分，切割需要采用单一尺寸来标注;
bool bNeedDimCutting = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrCutting);
if (bNeedDimCutting)
{
Point minYMinXPoint = mMainBeam.GetMinYMinXPoint();
Point maxYMinXPoint = mMainBeam.GetMaxYMinXPoint();
Vector upDimVector = new Vector(0, 1, 0);
Vector downDimVector = new Vector(0, -1, 0);
//A.判断主梁左侧的切割;
if (maxYMinXPoint.X > minYMinXPoint.X)
{
pointList.Clear();
pointList.Add(maxYMinXPoint);
pointList.Add(minYMinXPoint);
double dimDistance = CCommonPara.mDefaultDimDistance;
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, dimDistance, CCommonPara.mMainSizeDimPath);
}
if (maxYMinXPoint.X < minYMinXPoint.X)
{
pointList.Clear();
pointList.Add(maxYMinXPoint);
pointList.Add(minYMinXPoint);
double dimDistance = CCommonPara.mDefaultDimDistance;
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, downDimVector, dimDistance, CCommonPara.mMainSizeDimPath);
}
//B.判断主梁右侧的切割;
Point minYMaxXPoint = mMainBeam.GetMinYMaxXPoint();
Point maxYMaxXPoint = mMainBeam.GetMaxYMaxXPoint();
if (minYMaxXPoint.X > maxYMaxXPoint.X)
{
pointList.Clear();
pointList.Add(maxYMaxXPoint);
pointList.Add(minYMaxXPoint);
double dimDistance = CCommonPara.mDefaultDimDistance;
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, dimDistance, CCommonPara.mMainSizeDimPath);
}
else if (minYMaxXPoint.X < maxYMaxXPoint.X)
{
pointList.Clear();
pointList.Add(minYMaxXPoint);
pointList.Add(maxYMaxXPoint);
double dimDistance = CCommonPara.mDefaultDimDistance;
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, downDimVector, dimDistance, CCommonPara.mMainSizeDimPath);
}
}
}
/// <summary>
/// 绘制所有零件的上方标注;
/// </summary>
public void DrawAllPartUpDimX()
{
//移除主梁;
mMrPartList.Remove(mMainBeam);
List <Point> upDimPointList = new List <Point>();
bool bNeedUpDim = false;
//1.遍历获得所有零件的向上标注的点;
foreach (CMrPart mrPart in mMrPartList)
{
CMrDimSet partDimSet = mrPart.GetBeamTopViewInfo().GetPartUpDimSet();
if (partDimSet != null && partDimSet.Count > 0)
{
bNeedUpDim = true;
upDimPointList.AddRange(partDimSet.GetDimPointList());
}
}
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
//2.判断主梁的螺栓是否需要标注;
bool bNeedMainBeamBoltDim = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrBolt);
if (bNeedMainBeamBoltDim)
{
CMrDimSet mrDimSet = GetMainPartBoltUpDimX();
upDimPointList.AddRange(mrDimSet.GetDimPointList());
}
if (bNeedUpDim == false && bNeedMainBeamBoltDim == false)
{
return;
}
//3.默认把主梁的左右最小最大值点加入到链表中;
Point minXPoint = mMainBeam.GetMinXPoint();
Point maxXPoint = mMainBeam.GetMaxXPoint();
upDimPointList.Add(minXPoint);
upDimPointList.Add(maxXPoint);
PointList pointList = new PointList();
foreach (Point point in upDimPointList)
{
pointList.Add(point);
}
Vector upDimVector = new Vector(0, 1, 0);
mUpDimDistance = GetUpDimDistance(upDimPointList[0]);
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, mUpDimDistance, CCommonPara.mSizeDimPath);
mMrPartList.Add(mMainBeam);
}
/// <summary>
/// 标注工作点到主零件的距离之间尺寸;
/// </summary>
public void DrawWorkPointToMainPartDimX()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
bool bMarkValue = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrWorkPointToMainPart);
mMainBeam.SetNeedAddMarkFlag(bMarkValue);
//1.判断是否需要标注主梁与工作点之间的距离,采用一道尺寸来进行标注;
bool bNeedDimWpToMainPart = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrWorkPointToMainPart);
if (!bNeedDimWpToMainPart)
{
return;
}
Point mainBeamMinX = CMrMainBeam.GetInstance().GetMinXPoint();
Point mainBeamMaxX = CMrMainBeam.GetInstance().GetMaxXPoint();
Point leftWorkPoint = CMrMainBeam.GetInstance().mLeftWorkPoint;
Point rightWorkPoint = CMrMainBeam.GetInstance().mRightWorkPoint;
bMarkValue = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
mMainBeam.SetNeedAddMarkFlag(bMarkValue);
//2.如果工作点到工作点需要进行标注，而主部件左右侧与工作点的左右侧的距离都为0则不需要标注;
bool bNeedWorkPtToWorkPt = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
if (bNeedWorkPtToWorkPt)
{
double xDistanceLeft = Math.Abs(mainBeamMinX.X - leftWorkPoint.X);
double xDistanceRight = Math.Abs(mainBeamMaxX.X - rightWorkPoint.X);
if (xDistanceLeft < CCommonPara.mDblError && xDistanceRight < CCommonPara.mDblError)
{
return;
}
}
PointList pointList = new PointList();
pointList.Add(leftWorkPoint);
pointList.Add(rightWorkPoint);
pointList.Add(mainBeamMinX);
pointList.Add(mainBeamMaxX);
Vector upDimVector = new Vector(0, 1, 0);
mUpDimDistance = GetUpDimDistance(leftWorkPoint);
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, mUpDimDistance, CCommonPara.mMainSizeDimPath);
}
/// <summary>
/// 标注主零件的长度尺寸;
/// </summary>
public void DrawMainPartLengthDimX()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
//1.判断是否需要标注主梁的长度,如果需要采用单一的一道总尺寸;
bool bNeedDimMainPartLength = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrMainPartLength);
bool bMarkValue = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrMainPartLength);
mMainBeam.SetNeedAddMarkFlag(bMarkValue);
if (!bNeedDimMainPartLength)
{
return;
}
Point minXPoint = mMainBeam.GetMinXPoint();
Point maxXPoint = mMainBeam.GetMaxXPoint();
bMarkValue = beamTopViewSetting.FindMarkValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
mMainBeam.SetNeedAddMarkFlag(bMarkValue);
//2.如果需要标注工作点到工作点,并且主部件与工作点的距离左边或者右边为0，或者都为0时则不标注主部件长度;
bool bNeedWorkPtToWorkPt = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrWorkPointToWorkPoint);
if (bNeedWorkPtToWorkPt)
{
double xDistanceLeft = Math.Abs(minXPoint.X - CMrMainBeam.GetInstance().mLeftWorkPoint.X);
double xDistanceRight = Math.Abs(maxXPoint.X - CMrMainBeam.GetInstance().mRightWorkPoint.X);
if (xDistanceLeft < CCommonPara.mDblError || xDistanceRight < CCommonPara.mDblError)
{
return;
}
}
PointList pointList = new PointList();
pointList.Add(minXPoint);
pointList.Add(maxXPoint);
Vector upDimVector = new Vector(0, 1, 0);
mUpDimDistance = GetUpDimDistance(minXPoint);
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, upDimVector, mUpDimDistance, CCommonPara.mMainSizeDimPath);
}
/// <summary>
/// 绘制主梁的Bolt在Y向上的标注;
/// </summary>
private void DrawMainPartBoltDimY()
{
CBeamTopViewSetting beamTopViewSetting = CBeamDimSetting.GetInstance().mTopViewSetting;
bool bNeedMainBeamBoltDim = beamTopViewSetting.FindDimValueByName(CBeamTopViewSetting.mstrBolt);
if (!bNeedMainBeamBoltDim)
{
return;
}
List <CMrDimSet> boltDimSetList = GetMainPartBoltDimSetY();
if (boltDimSetList == null || boltDimSetList.Count == 0)
{
return;
}
foreach (CMrDimSet mrDimSet in boltDimSetList)
{
if (mrDimSet == null || mrDimSet.Count <= 1)
{
continue;
}
if (!IsNeedMrDimSetDim(mrDimSet))
{
continue;
}
List <Point> dimPointList = mrDimSet.GetDimPointList();
PointList pointList = new PointList();
foreach (Point point in dimPointList)
{
pointList.Add(point);
}
double dimDistance = mrDimSet.mDimDistance;
Vector dimVector = mrDimSet.mDimVector;
CDimTools.GetInstance().DrawDimensionSet(mViewBase, pointList, dimVector, dimDistance, CCommonPara.mSizeDimPath);
}
}
/// <summary>
/// 私有构造函数;
/// </summary>
private CBeamDimSetting()
{
mTopViewSetting = new CBeamTopViewSetting();
mFrontViewSetting = new CBeamFrontViewSetting();
mSectionViewSetting = new CBeamSectionViewSetting();
}