private void button3_Click(object sender, EventArgs e)
{
C4UFX.CANMessage mess = new C4UFX.CANMessage();
CANControls.FndTnd nd = new CANControls.FndTnd();
nd.Fn = 0x7F; // highest possible 7 bit value as this node. Doesn't really matter from who
nd.Fd = 1; // also doesn't really matter from which device
nd.Tn = 2; // To Node 2
nd.Td = 1; // To Device 1 (1st output)
mess.ID = CANControls.ConvNDID(nd);
mess.Data[0] = 0x30; // toggle on/off
mess.DLC = 1; // send one byte
CANControls.SendCANMessage(mess);
}
private void button2_Click(object sender, EventArgs e)
{
// this test assumes the light switch is node 1 and will program switch 3
// (middle left button)
C4UFX.CANMessage mess = new C4UFX.CANMessage();
CANControls.FndTnd nd = new CANControls.FndTnd();
nd.Fn = 0x7F; // highest possible 7 bit value as this node. Doesn't really matter from who
nd.Fd = 0; // device
nd.Tn = 1; // To Node 1
nd.Td = 0; // To Device 0 (node itself)
mess.ID = CANControls.ConvNDID(nd);
mess.Data[0] = 0x1A; // unlock code from protocol overview doc
mess.Data[1] = 0x01; // unlock code from protocol overview doc
mess.Data[2] = 0xFE; // unlock code from protocol overview doc
mess.Data[3] = 0x00; // unlock code from protocol overview doc
mess.DLC = 4; // send 4 bytes
CANControls.SendCANMessage(mess); // unlocks node for programming
// ######## set new address for switch itself
nd.Fn = 0x7F; // highest possible 7 bit value as this node. Doesn't really matter from who
nd.Fd = 0; // device
nd.Tn = 1; // To Node 1
nd.Td = 3; // To Device 3 (switch 3)
mess.ID = CANControls.ConvNDID(nd);
mess.Data[0] = 0x21; // CmdSysPPar command - see "Smart switch protocol details.doc"
mess.Data[1] = 0x01; // mode = enabled
mess.Data[2] = 0x05; // double click time = 5*50ms
mess.Data[3] = 0x06; // hold time = 6*50ms
mess.DLC = 4; // send 4 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## we can reuse the same address for next commands
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x01; // sub command 1
//mess.Data[2] = 0x01; // first click event goes to node 1
//mess.Data[3] = 0x01; // first click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x30; // command 30 is on/off toggle (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## now repeat for sub commands 2-7
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x02; // sub command 2
//mess.Data[2] = 0x01; // second click event goes to node 1
//mess.Data[3] = 0x01; // second click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x30; // command 30 is on/off toggle (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## sub 3
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x03; // sub command 3
//mess.Data[2] = 0x01; // double click event goes to node 1
//mess.Data[3] = 0x01; // double click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x31; // command 31 is full on (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## sub 4
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x04; // sub command 4
//mess.Data[2] = 0x01; // 1st hold event goes to node 1
//mess.Data[3] = 0x01; // 1st hold click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x32; // command 32 is fade continous (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## sub 5
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x05; // sub command 5
//mess.Data[2] = 0x01; // 2nd hold event goes to node 1
//mess.Data[3] = 0x01; // 2nd hold click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x32; // command 32 is fade continous (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## sub 6
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x06; // sub command 6 -
//mess.Data[2] = 0x01; // release event goes to node 1
//mess.Data[3] = 0x01; // release click event goes to device 1
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x33; // command 33 is release (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
//// ######## sub 7
//mess.Data[0] = 0x22; // CmdSysPPar2 command - see "Smart switch protocol details.doc"
//mess.Data[1] = 0x07; // sub command 7 -
//mess.Data[2] = 0xFF; // 1st press event is not used and set to 255
//mess.Data[3] = 0xFF; // 1st press event is not used and set to 255
//mess.Data[4] = 0x01; // send one additional command byte
//mess.Data[5] = 0x00; // no command (from "device description for dimming output")
//mess.DLC = 6; // send 6 bytes
//CANControls.SendCANMessage(mess); // unlocks node for programming
}