Exemplo n.º 1
0
//		ExtrudedElement(
//			string name,
//			Profile profile,
//			double length,
//			Coordinate3D position,
//			Direction3D zAxis,
//			Direction3D xAxis,
//			Direction3D extrudeDirection,
//			Element container)
//			:this (name, profile, length, position, zAxis, xAxis, extrudeDirection,
//			       container.ObjectLocalPlacement, container.IfcElement.OwnerHistory)
//		{}
//
//		ExtrudedElement(
//			string name,
//			Profile profile,
//			double length,
//			Coordinate3D position,
//			Direction3D zAxis,
//			Direction3D xAxis,
//			Direction3D extrudeDirection,
//			SpatialElement container)
//			:this (name, profile, length, position, zAxis, xAxis, extrudeDirection,
//			       container.ObjectLocalPlacement, container.IfcSpatialStructureElement.OwnerHistory)
//		{}

        BbExtrudedElement(
            string name,
            BbProfile profile,
            double length,
            BbCoordinate3D position,
            BbDirection3D zAxis,
            BbDirection3D xAxis,
            BbDirection3D extrudeDirection,
            BbLocalPlacement3D containerLocation,
            IfcOwnerHistory ownerHistory,
            Type ifcEntityType)
        {
            Name    = name;
            Profile = profile;
            Length  = length;
            BbPosition3D pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                containerLocation, pos);

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                Length);

            _ifcElement              = Activator.CreateInstance(ifcEntityType) as IfcElement;
            _ifcElement.GlobalId     = IfcGloballyUniqueId.NewGuid();
            _ifcElement.OwnerHistory = ownerHistory;
            _ifcElement.Name         = Name;
            //ObjectType = ,
            _ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
            _ifcElement.Representation  = bbExtrudedGeometry.IfcProductDefinitionShape;
        }
Exemplo n.º 2
0
        //        ExtrudedElement(
        //            string name,
        //            Profile profile,
        //            double length,
        //            Coordinate3D position,
        //            Direction3D zAxis,
        //            Direction3D xAxis,
        //            Direction3D extrudeDirection,
        //            Element container)
        //            :this (name, profile, length, position, zAxis, xAxis, extrudeDirection,
        //                   container.ObjectLocalPlacement, container.IfcElement.OwnerHistory)
        //        {}
        //
        //        ExtrudedElement(
        //            string name,
        //            Profile profile,
        //            double length,
        //            Coordinate3D position,
        //            Direction3D zAxis,
        //            Direction3D xAxis,
        //            Direction3D extrudeDirection,
        //            SpatialElement container)
        //            :this (name, profile, length, position, zAxis, xAxis, extrudeDirection,
        //                   container.ObjectLocalPlacement, container.IfcSpatialStructureElement.OwnerHistory)
        //        {}
        BbExtrudedElement(
			string name,
			BbProfile profile,
			double length,
			BbCoordinate3D position,
			BbDirection3D zAxis,
			BbDirection3D xAxis,
			BbDirection3D extrudeDirection,
			BbLocalPlacement3D containerLocation,
			IfcOwnerHistory ownerHistory,
			Type ifcEntityType)
        {
            Name = name;
            Profile = profile;
            Length = length;
            BbPosition3D pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                containerLocation, pos	);

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                Length);

            _ifcElement = Activator.CreateInstance(ifcEntityType) as IfcElement;
            _ifcElement.GlobalId = IfcGloballyUniqueId.NewGuid();
            _ifcElement.OwnerHistory = ownerHistory;
            _ifcElement.Name = Name;
                //ObjectType = ,
            _ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
            _ifcElement.Representation = bbExtrudedGeometry.IfcProductDefinitionShape;
        }
Exemplo n.º 3
0
        BbBrepElement(
            string name,
            BbBRepGeometry brepGeometry,
            BbCoordinate3D position,
            BbDirection3D zAxis,
            BbDirection3D xAxis,
            BbLocalPlacement3D containerLocation,
            IfcOwnerHistory ownerHistory,
            Type IfcEntityType)
        {
            Name = name;
            //Profile = profile;
            BbPosition3D pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                containerLocation, pos	);

            //			ifcBuildingElement = Activator.CreateInstance(EbConstants.Part21NSName, EbConstants.Part21NSName + "." + ifcEntityName);
            ifcElement = Activator.CreateInstance(IfcEntityType) as IfcElement;

            ifcElement.GlobalId = IfcGloballyUniqueId.NewGuid();
            ifcElement.OwnerHistory = ownerHistory;
            ifcElement.Name = Name;
            //ObjectType = ,
            ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
            ifcElement.Representation = brepGeometry.IfcProductDefinitionShape;
        }
Exemplo n.º 4
0
        private BbPiece(string name, string objectType, BbProfile profile,
                        double length, BbCoordinate3D position, BbDirection3D zAxis,
                        BbDirection3D xAxis, BbDirection3D extrudeDirection,
                        BbLocalPlacement3D hostPlacement, Type ifcEntityType)
        {
            Length  = length;
            Profile = profile;
            var pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostPlacement, pos);

            var semExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                extrudeDirection,
                Length);

            _ifcElement = Activator.CreateInstance(ifcEntityType) as IfcElement;
            if (_ifcElement == null)
            {
                return;
            }

            _ifcElement.GlobalId        = IfcGloballyUniqueId.ConvertToIfcGuid(Guid);
            _ifcElement.OwnerHistory    = BbHeaderSetting.Setting3D.IfcOwnerHistory;
            _ifcElement.Name            = name;
            _ifcElement.ObjectType      = objectType;
            _ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
            _ifcElement.Representation  = semExtrudedGeometry.IfcProductDefinitionShape;
            //_ifcElement.Tag = id;
        }
Exemplo n.º 5
0
        public static BbLocalPlacement3D Create(BbLocalPlacement3D placementRelTo, BbPosition3D relativePlacement)
        {
            var placement3D = new BbLocalPlacement3D(placementRelTo, relativePlacement);

            BbInstanceDB.AddToExport(placement3D);
            return(placement3D);
        }
Exemplo n.º 6
0
        BbBrepElement(
            string name,
            BbBRepGeometry brepGeometry,
            BbCoordinate3D position,
            BbDirection3D zAxis,
            BbDirection3D xAxis,
            BbLocalPlacement3D containerLocation,
            IfcOwnerHistory ownerHistory,
            Type IfcEntityType)
        {
            Name = name;
            //Profile = profile;
            BbPosition3D pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                containerLocation, pos);



//			ifcBuildingElement = Activator.CreateInstance(EbConstants.Part21NSName, EbConstants.Part21NSName + "." + ifcEntityName);
            ifcElement = Activator.CreateInstance(IfcEntityType) as IfcElement;

            ifcElement.GlobalId     = IfcGloballyUniqueId.NewGuid();
            ifcElement.OwnerHistory = ownerHistory;
            ifcElement.Name         = Name;
            //ObjectType = ,
            ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
            ifcElement.Representation  = brepGeometry.IfcProductDefinitionShape;
        }
Exemplo n.º 7
0
        public static BbLocalPlacement3D Create(BbLocalPlacement3D placementRelTo)
        {
            var placement3D = new BbLocalPlacement3D(placementRelTo);

            BbInstanceDB.AddToExport(placement3D);
            return(placement3D);
        }
Exemplo n.º 8
0
 BbLocalPlacement3D(
     BbLocalPlacement3D placementRelTo, BbPosition3D relativePlacement)
 {
     if (placementRelTo != null && relativePlacement != null)
     {
         IfcLocalPlacement = new IfcLocalPlacement
         {
             PlacementRelTo    = placementRelTo.IfcLocalPlacement,
             RelativePlacement = new IfcAxis2Placement
             {
                 Value = relativePlacement.IfcAxis2Placement3D,
             },
         };
     }
     else if (placementRelTo == null && relativePlacement != null)
     {
         IfcLocalPlacement = new IfcLocalPlacement
         {
             RelativePlacement = new IfcAxis2Placement
             {
                 Value = relativePlacement.IfcAxis2Placement3D,
             },
         };
     }
     else
     {
         IfcLocalPlacement = new IfcLocalPlacement
         {
             RelativePlacement = new IfcAxis2Placement
             {
                 Value = BbHeaderSetting.Setting3D.DefaultBbPosition3D.IfcAxis2Placement3D,
             },
         };
     }
 }
Exemplo n.º 9
0
        public static BbLocalPlacement3D Create(IfcLocalPlacement ifcLocalPlacement)
        {
            var placement3D = new BbLocalPlacement3D(ifcLocalPlacement);

            BbInstanceDB.AddToExport(placement3D);
            return(placement3D);
        }
Exemplo n.º 10
0
        public BbCutCope(
            BbElement hostElement,
            BbProfile profile,
            double length,
            double[] zAxis,
            double[] xAxis,
            double[] extrudeDirection,
            double[] position)
        {
            //ObjectLocalPlacement = new LocalPlacement3D(hostElement.ObjectLocalPlacement, new Position3D(position));

            /// from main piece
            BbPosition3D pos = BbPosition3D.Create(
                BbCoordinate3D.Create(position),
                BbDirection3D.Create(zAxis),
                BbDirection3D.Create(xAxis));

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostElement.ObjectBbLocalPlacement, pos);

            BbDirection3D exDir;

            if (Math.Round(extrudeDirection[0], 8) == 0.0 && Math.Round(extrudeDirection[0], 8) == 0 && Math.Round(extrudeDirection[0], 8) == 1)
            {
                exDir = BbHeaderSetting.Setting3D.ZAxis;
            }
            else
            {
                exDir = BbDirection3D.Create(extrudeDirection);
            }


            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                exDir,
                length);

            _ifcOpeningElement = new IfcOpeningElement
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = hostElement.IfcObject.OwnerHistory,
                // Name =
                // Description =
                ObjectType      = "Opening",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = bbExtrudedGeometry.IfcProductDefinitionShape,
            };

            _ifcRelVoidsElement = new IfcRelVoidsElement
            {
                GlobalId                = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory            = hostElement.IfcObject.OwnerHistory,
                Name                    = "Cope",
                RelatingBuildingElement = hostElement.IfcObject as IfcElement,
                RelatedOpeningElement   = _ifcOpeningElement,
            };
        }
Exemplo n.º 11
0
        protected void AddBoltDirection(BbCurveGeometry boltDirection, BbCoordinate3D position)
        {
            BoltDirection = boltDirection;
            var pos = BbPosition3D.Create(position, BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                MainElement.ObjectBbLocalPlacement, pos);

            _ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
        }
Exemplo n.º 12
0
        public void AddWeldingPath(BbCurveGeometry weldingPath, BbCoordinate3D position)
        {
            WeldingPath = weldingPath;
            var pos = BbPosition3D.Create(position,
                                          BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                MainElement.ObjectBbLocalPlacement, pos);

            _ifcElement.ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement;
        }
Exemplo n.º 13
0
        public BbCutCope(
            BbElement hostElement,
            double copeWidth,
            double copeDepth,
            double copeRadius,
            double[] position)
        {
            BbCopeProfile profile = BbCopeProfile.Create(copeWidth, copeDepth, copeRadius);

            var mainPart = hostElement as BbPiece;

            if (mainPart == null)
            {
                return;
            }

            BbPosition3D pos = BbPosition3D.Create(
                BbCoordinate3D.Create(position),
                BbHeaderSetting.Setting3D.XAxisMinus,
                BbHeaderSetting.Setting3D.ZAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostElement.ObjectBbLocalPlacement, pos);

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                mainPart.Profile.Width);

            _ifcOpeningElement = new IfcOpeningElement
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = hostElement.IfcObject.OwnerHistory,
                // Name =
                // Description =
                ObjectType      = "Opening",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = bbExtrudedGeometry.IfcProductDefinitionShape,
            };

            _ifcRelVoidsElement = new IfcRelVoidsElement
            {
                GlobalId                = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory            = hostElement.IfcObject.OwnerHistory,
                Name                    = "Cope",
                RelatingBuildingElement = hostElement.IfcObject as IfcElement,
                RelatedOpeningElement   = _ifcOpeningElement,
            };
        }
Exemplo n.º 14
0
        protected BbSite(
            Guid guid, string name, string description, string longname, string compositionType, BbProject project)

        {
            Guid = guid;

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(BbHeaderSetting.Setting3D.DefaultBbPosition3D);

            IfcSpatialStructureElement = new IfcSite
            {
                GlobalId        = IfcGloballyUniqueId.ConvertToIfcGuid(guid),
                OwnerHistory    = BbHeaderSetting.Setting3D.IfcOwnerHistory,
                Name            = name,
                Description     = description,
                LongName        = longname,
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                //                CompositionType = IfcElementCompositionEnum.ELEMENT,
            };

            if (compositionType.ToLower() == @"complex")
            {
                IfcSpatialStructureElement.CompositionType = IfcElementCompositionEnum.COMPLEX;
            }
            else if (compositionType.ToLower() == @"partial")
            {
                IfcSpatialStructureElement.CompositionType = IfcElementCompositionEnum.PARTIAL;
            }
            else
            {
                IfcSpatialStructureElement.CompositionType = IfcElementCompositionEnum.ELEMENT;
            }

            BbProject = project;


            if (true)
            {
                IfcRelAggregates = new IfcRelAggregates()
                {
                    GlobalId       = IfcGloballyUniqueId.NewGuid(),
                    OwnerHistory   = BbHeaderSetting.Setting3D.IfcOwnerHistory,
                    RelatingObject = BbProject.IfcObject,
                    RelatedObjects = new List <IfcObjectDefinition>()
                    {
                        IfcSpatialStructureElement
                    },
                };
            }
        }
Exemplo n.º 15
0
        BbFloor(
            string name,
            double elevation,
            BbBuilding building)
        {
            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(building.ObjectBbLocalPlacement, BbHeaderSetting.Setting3D.DefaultBbPosition3D);

            IfcSpatialStructureElement = new IfcBuildingStorey
            {
                GlobalId = IfcGloballyUniqueId.NewGuid(),

                OwnerHistory = BbHeaderSetting.Setting3D.IfcOwnerHistory,
                Name         = name,
                //Description = "",
                //ObjectType = "",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                //Representation =
                //LongName = "",
                CompositionType = IfcElementCompositionEnum.ELEMENT,
                Elevation       = elevation,
            };

            //building.AddFloor(this);
            BbBuilding = building;

            if (true)
            {
                IfcRelAggregates = new IfcRelAggregates()
                {
                    GlobalId       = IfcGloballyUniqueId.NewGuid(),
                    OwnerHistory   = BbHeaderSetting.Setting3D.IfcOwnerHistory,
                    RelatingObject = BbBuilding.IfcSpatialStructureElement,
                    RelatedObjects = new List <IfcObjectDefinition>()
                    {
                        IfcSpatialStructureElement
                    },
                };
            }
        }
Exemplo n.º 16
0
        BbLocalPlacement3D(
           BbLocalPlacement3D placementRelTo, BbPosition3D relativePlacement)
        {
            if (placementRelTo != null && relativePlacement != null)
            {
                IfcLocalPlacement = new IfcLocalPlacement
                {
                    PlacementRelTo = placementRelTo.IfcLocalPlacement,
                    RelativePlacement = new IfcAxis2Placement
                    {
                        Value = relativePlacement.IfcAxis2Placement3D,
                    },

                };
            }
            else if (placementRelTo == null && relativePlacement != null)
            {
                IfcLocalPlacement = new IfcLocalPlacement
                {
                    RelativePlacement = new IfcAxis2Placement
                    {
                        Value = relativePlacement.IfcAxis2Placement3D,
                    },

                };
            }
            else
            {
                IfcLocalPlacement = new IfcLocalPlacement
                {

                    RelativePlacement = new IfcAxis2Placement
                    {
                        Value = BbHeaderSetting.Setting3D.DefaultBbPosition3D.IfcAxis2Placement3D,
                    },

                };
            }
        }
Exemplo n.º 17
0
        public static bool Tester4Writer(string filename)
        {
            EarlyBindingInstanceModel.Reset();
            BbInstanceDB.Reset();
            //var em11PsetName = @"AISC_EM11_Pset_Status";
            BbHeaderSetting.Create(
                "donghoon", "Georgia Tech", "sem Tool", "alpha 1", "gatech", BbUnit.Metric);
            var floor = BbFloor.CreateSingleStoreyProject(
                "project", "site", "building", "1st floor", 0);

            // assembly 1-Beam-------------------------------------------------------------------------------------

            var assembly = BbAssembly.Create(
                "assid001",
                "Steel Assembly",
                "ASS01",
                "client_marker",
                "prelim_marker",
                "ship_mark",
                "102301123423", floor,
                BbCoordinate3D.Create(0, 0, 6000), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis);

            // assembly 1 properties
            //Quantity
            var qAssemBeam = BbQuantityRequired.Create();

            qAssemBeam.Add(assembly);
            //Finish/tearment
            //var paintAssem = BbPaintFinish.Create();
            //var paintAssem = BbPaintFinish.Create("Paint", "PAINTED", assembly);
            //paintAssem.AddToElement(assembly);
//            assembly.AddPaintFinish(paintAssem);

            var pSetAssemSTr01  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintAssem1Pset = BbSurfaceTreatmentProperty.Create(pSetAssemSTr01, new List <string> {
                "Painted"
            });

            paintAssem1Pset.AssignTo(assembly);
            //Scheduling
            var pSetAssemSc01 = BbPropertySet.Create(@"AISC_EM11_Pset_Schedule");
            var AssemSch01    = BbSchedule.Create(pSetAssemSc01, "seq01", "seqLevel 01", DateTime.Now);

            AssemSch01.AssignTo(assembly);
            //Status
            var pSetAssemSt01 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var AssemStat01   = BbStatus.Create(pSetAssemSt01, "Default", "Default", true);

            AssemStat01.AssignTo(assembly);
            //Drawing number
            var pSetAssemDN01     = BbPropertySet.Create(@"AISC_EM11_Pset_DrawingNumber");
            var DnumberAssem1Pset = BbDrawingNumber.Create(pSetAssemDN01, new List <string> {
                "DR001PH1005", "DR001PH1004"
            });

            DnumberAssem1Pset.AssignTo(assembly);
            //Version
            var pSetAssemVr01  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionAssem01 = BbVersion.Create(pSetAssemVr01, "versionAssem01");

            versionAssem01.AssignTo(assembly);


            // main piece 1- Beam------------------------------------------------------------------------------------
            var profile  = BbNamedIProfile.Create("AISC", "W460X260", 260, 508, 22.6, 40.4);
            var mainPart = BbMainPiece.Create(
                "P0001",
                "main piece", profile, 6000,
                BbCoordinate3D.Create(0, 0, -254),
                BbHeaderSetting.Setting3D.XAxis,
                BbHeaderSetting.Setting3D.YAxis,
                assembly);
            //var beamType = SemBeamType.Create("wideflange", "pm0001", IfcBeamTypeEnum.BEAM);
            //beamType.Defines(mainPart);

            // Main piece 1-Beam properties
            //Identification
            var pieceIdBeam01 = BbPieceIdentity.Create("indMark001", "pieceMark001", "prelimMark001", "barcode123456890", true);

            pieceIdBeam01.AssignTo(mainPart);
            //Material

            var pSetMat2       = BbPropertySet.Create(@"AISC_EM11_Pset_MaterialProperty");
            var materialBeam01 = BbMaterial.Create("ASTM A992", pSetMat2, "materialID001", "materialCert001", "materialGrade001", "materialType001");

            materialBeam01.AssociateTo(mainPart);

            //Quantity
            var qBeam = BbQuantityRequired.Create();

            qBeam.Add(mainPart);
            //Finish/treatment
            ////var paint2 = PaintFinish.Create("p1001", "antirust", "paint");
            var coord2d00 = BbCoordinate2D.Create(-100, 0);
            var coord2d01 = BbCoordinate2D.Create(100, 0);
            var coord2d02 = BbCoordinate2D.Create(100, 3400);
            var coord2d03 = BbCoordinate2D.Create(-100, 3400);
            var poly2d0   = BbPolyline2D.Create(new[] { coord2d00, coord2d01, coord2d02, coord2d03 });

            var coord2d10 = BbCoordinate2D.Create(-40, 1500);
            var coord2d11 = BbCoordinate2D.Create(40, 1500);
            var coord2d12 = BbCoordinate2D.Create(40, 2500);
            var coord2d13 = BbCoordinate2D.Create(-40, 2500);
            var poly2d1   = BbPolyline2D.Create(new[] { coord2d10, coord2d11, coord2d12, coord2d13 });

            var sg = BbSurfaceGeometry.Create(poly2d0, new[] { poly2d1 });
            //var paint3 = SemPaintFinishPatch.Create("ANTIRUST", "PAINTED", sg);

            var ploc = BbLocalPlacement3D.Create(
                mainPart.ObjectBbLocalPlacement,
                BbPosition3D.Create(
                    BbCoordinate3D.Create(0, 254, 100),
                    BbHeaderSetting.Setting3D.YAxis,
                    BbHeaderSetting.Setting3D.XAxisMinus)
                );

            //paint3.AddToElement(mainPart, ploc);

            var pSetBeamSTr01  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintBeam1Pset = BbSurfaceTreatmentProperty.Create(pSetBeamSTr01, new List <string> {
                "GALVANIZED"
            });

            paintBeam1Pset.AssignTo(mainPart);
            //Status
            var pSetBeamSt01 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var statusBeam01 = BbStatus.Create(pSetBeamSt01, "Default", "Default", false);

            statusBeam01.AssignTo(mainPart);
            //Version
            var pSetBeamVr01  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionBeam01 = BbVersion.Create(pSetBeamVr01, "versionBeam01");

            versionBeam01.AssignTo(mainPart);
            //Tolerance
            var pSetBeamLT01    = BbPropertySet.Create(@"AISC_EM11_Pset_ToleranceForLayout");
            var toleranceBeam01 = BbLayoutTolerance.Create(pSetBeamLT01, 0.01);

            toleranceBeam01.AssignTo(mainPart);
            //Catellation
            //No castellation needed

            //Feature

            //SemAnnotation.Create
            //    ("north", "LocationOfMark", mainPart, BbCoordinate3D.Create(0, 254, 5), BbDirection3D.YAxis2D,
            //        BbDirection3D.XAxisMinus2D);

            //BbPosition3D pos = BbPosition3D.Create(
            //    BbCoordinate3D.Create(0, 0, 100),
            //    BbDirection3D.Create(0.215665546, -0.107832773, -0.970494959),
            //    BbDirection3D.Create(-0.970494959, 0.107832773, -0.215665546)
            //    );

            //BbSkewedEnd.Create(mainPart, pos);


            ////            var arb = ArbitraryProfile.Create(poly2d0);
            ////
            ////            ExtrudedElement.Create(
            ////                "new", arb, 10, Coordinate3D.Create(0, 254, 100),
            ////                Direction3D.YAxis2D, Direction3D.XAxisMinus2D,
            ////                mainPart, typeof(IfcPlate));

            ////// TypeProduct.Create(mainPart, "main piece", typeof(IfcBeam));


            //BbCutCope.Create(mainPart, 210, 50, 10, SemCopeLocation.BottomRight);
            //BbCutCope.Create(mainPart, 210, 50, 10, SemCopeLocation.TopRight);
            ////CutCope.Create(mainPart, 210, 50, 10, CopeLocation.BottomLeft);
            ////CutCope.Create(mainPart, 210, 50, 10, CopeLocation.TopLeft);

            var bHoleBeam01 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(1100, 60), 30, SemHoleLocation.Bottom, false);
            var bHoleBeam02 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(1100, -60), 30, SemHoleLocation.Bottom, true);
            var bHoleBeam03 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(1200, 60), 30, SemHoleLocation.Top, true);
            var bHoleBeam04 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(1200, -60), 30, SemHoleLocation.Top, false);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(300, 60), 15, HoleLocation.Left, false);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(400, -60), 15, HoleLocation.Left, true);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(500, 60), 15, HoleLocation.Right, false);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(600, -60), 15, HoleLocation.Right, true);
            var bHoleBeam05 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(700, 60), 15, SemHoleLocation.Web, false);
            var bHoleBeam06 = BbDrillHoles.Create(mainPart, BbCoordinate2D.Create(800, -60), 15, SemHoleLocation.Web, true);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(6000 - 106.5, -100), 15, HoleLocation.Web, true);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(6000 - 91.5, 100), 20, HoleLocation.Web, true);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(101.5 + 5, -100), 15, HoleLocation.Web, true);
            //DrillHoles.Create(mainPart, Coordinate2D.Create(101.5 + 5, 100), 15, HoleLocation.Web, true);

            //Beam Bolt Hole properties
            var pSetBeamBH01      = BbPropertySet.Create(@"AISC_EM11_Pset_BoltHole");
            var boltHoleBeamPset1 = BbBoltHoleProperties.Create(pSetBeamBH01, "Drilling", "Top", "No design constraint", "Tapped Hole", 30, false, 0);

            boltHoleBeamPset1.AssignTo(bHoleBeam01);
            boltHoleBeamPset1.AssignTo(bHoleBeam02);
            boltHoleBeamPset1.AssignTo(bHoleBeam03);
            boltHoleBeamPset1.AssignTo(bHoleBeam04);
            boltHoleBeamPset1.AssignTo(bHoleBeam05);
            boltHoleBeamPset1.AssignTo(bHoleBeam06);

            // Stiffeners-------------------------------------------------------------------------------------------
            //Stiffener1
            var stiffener1 = BbStiffener.Create("st00102", "stiffener", 100, 425, 35,
                                                BbCoordinate3D.Create(65, 0, 5000), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis, mainPart);
            //Stifenner1 properties
            //Identification
            var stiffIdentity1 = BbPieceIdentity.Create("indMark002", "pieceMark002", "prelimMark002", "barcode123456892", false);

            stiffIdentity1.AssignTo(stiffener1);
            //Status
            var pSetStstiff01 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var statusstiff01 = BbStatus.Create(pSetStstiff01, "ReadyForProcurement", "Default", true);

            statusstiff01.AssignTo(stiffener1);
            //Version
            var pSetVrstiff01  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionstiff01 = BbVersion.Create(pSetVrstiff01, "versionStiff01");

            versionstiff01.AssignTo(stiffener1);
            //Tolerance
            var pSetLystiff01    = BbPropertySet.Create(@"AISC_EM11_Pset_ToleranceForLayout");
            var tolerancestiff01 = BbLayoutTolerance.Create(pSetLystiff01, 0.01);

            tolerancestiff01.AssignTo(stiffener1);
            //Quantity
            var qStiff = BbQuantityRequired.Create();

            qStiff.Add(stiffener1);
            //Material
            var pSetMat1      = BbPropertySet.Create(@"AISC_EM11_Pset_MaterialProperty");
            var materialStiff = BbMaterial.Create("ASTM A992", pSetMat1, "materialID002",
                                                  "materialCert002", "materialGrade002", "materialType002");

            materialStiff.AssociateTo(stiffener1);
            //Finish/treatment
            //var paintStiff = BbPaintFinish.Create("stiffener paint", "PAINTED", stiffener1);
            //paintStiff.AddToElement(stiffener1);

            var pSetSTstiff01  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintStiffPset = BbSurfaceTreatmentProperty.Create(pSetSTstiff01, new List <string> {
                "Galvanized"
            });

            paintStiffPset.AssignTo(stiffener1);

            //Stiffener2-------------------------------
            var stiffener2 = BbStiffener.Create("st00102", "stiffener", 100, 425, 35,
                                                BbCoordinate3D.Create(-65, 0, 5000), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis, mainPart);
            //Stifenner2 properties
            //Identification
            var stiffIdentity2 = BbPieceIdentity.Create("indMark003", "pieceMark003", "prelimMark003", "barcode123456893", false);

            stiffIdentity2.AssignTo(stiffener2);
            //Status
            statusstiff01.AssignTo(stiffener2);
            //Version
            versionstiff01.AssignTo(stiffener2);
            //Tolerance
            tolerancestiff01.AssignTo(stiffener2);
            //Quantity
            qStiff.Add(stiffener2);
            //Material
            materialStiff.AssociateTo(stiffener2);
            //Finish/treatment
            //paintStiff.AddToOtherElement(stiffener2);
//            stiffener2.AddPaintFinish(paintStiff);
            //paintStiffPset.AssignTo(stiffener2);

            //Stiffener3-------------------------------
            var stiffener3 = BbStiffener.Create("st00102", "stiffener", 100, 425, 35,
                                                BbCoordinate3D.Create(65, 0, 4600), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis, mainPart);
            //Stifenner3 properties
            //Identification
            var stiffIdentity3 = BbPieceIdentity.Create("indMark004", "pieceMark004", "prelimMark004", "barcode123456894", false);

            stiffIdentity3.AssignTo(stiffener3);
            //Status
            statusstiff01.AssignTo(stiffener3);
            //Version
            versionstiff01.AssignTo(stiffener3);
            //Tolerance
            tolerancestiff01.AssignTo(stiffener3);
            //Quantity
            qStiff.Add(stiffener3);
            //Material
            materialStiff.AssociateTo(stiffener3);
            //Finish/treatment
            //paintStiff.AddToOtherElement(stiffener3);
            //stiffener3.AddPaintFinish(paintStiff);
            //paintStiffPset.AssignTo(stiffener3);

            //Stiffener4-------------------------------
            var stiffener4 = BbStiffener.Create("st00102", "stiffener", 100, 425, 35,
                                                BbCoordinate3D.Create(-65, 0, 4600), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis, mainPart);
            //Stifenner4 properties
            //Identification
            var stiffIdentity4 = BbPieceIdentity.Create("indMark005", "pieceMark005", "prelimMark005", "barcode123456895", false);

            stiffIdentity4.AssignTo(stiffener4);
            //Status
            statusstiff01.AssignTo(stiffener4);
            //Version
            versionstiff01.AssignTo(stiffener4);
            //Tolerance
            tolerancestiff01.AssignTo(stiffener4);
            //Quantity
            qStiff.Add(stiffener4);
            //Material
            materialStiff.AssociateTo(stiffener4);
            //Finish/treatment
            //paintStiff.AddToOtherElement(stiffener4);
            //stiffener4.AddPaintFinish(paintStiff);
            //paintStiffPset.AssignTo(stiffener4);

            // welding stiffeners with beam //DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD


            //BbSlottedHole.Create(mainPart, BbCoordinate2D.Create(3000, 50), 70, 30, BbDirection2D.RefDirection2D,
            //    SemHoleLocation.Web, true);

            //2 Clip angles for column1----------------------------------------------------------------------------------

            var aProfile = BbNamedLProfile.Create("AISC", "L203X152X19", 203, 152, 19);

            var derived1 = BbDerivedProfile.Create(aProfile, false, true);
            // -90.3 for showing gap between elements
            var angle = BbClipAngle.Create(
                "a00102",
                "angle",
                derived1, 360,
                //BbCoordinate3D.Create(5898.5, 90.3, -180 - 254),
                BbCoordinate3D.Create(90.3, -180, 5898.5),
                BbHeaderSetting.Setting3D.YAxis, BbHeaderSetting.Setting3D.Axis,
                mainPart
                );

            //var w000 = BbCoordinate3D.Create(5898.5, 0, 0);
            //var w001 = BbCoordinate3D.Create(5898.5, 0, 200);
            var w000          = BbCoordinate3D.Create(5898.5, 0, 0);
            var w001          = BbCoordinate3D.Create(5898.5, 0, 200);
            var curve         = BbPolyline3D.Create(new BbCoordinate3D[] { w000, w001 });
            var curveGeometry = BbCurveGeometry.Create(curve);

            //Clip angle 1 properties
            //Identification
            var angleIdentity1 = BbPieceIdentity.Create("indMark006", "pieceMark006", "prelimMark006", "barcode123456896", false);

            angleIdentity1.AssignTo(angle);
            //Status
            var pSetStAngle01 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var statusAngle01 = BbStatus.Create(pSetStAngle01, "ReadyForProcurement", "Default", false);

            statusAngle01.AssignTo(angle);
            //Version
            var pSetVrAngle01  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionAngle01 = BbVersion.Create(pSetVrAngle01, "versionAngle001");

            versionAngle01.AssignTo(angle);
            //Tolerance
            var pSetLyAngle01    = BbPropertySet.Create(@"AISC_EM11_Pset_ToleranceForLayout");
            var toleranceAngle01 = BbLayoutTolerance.Create(pSetLyAngle01, 0.01);

            toleranceAngle01.AssignTo(angle);
            //Quantity
            var qAngle = BbQuantityRequired.Create();

            qAngle.Add(angle);
            //Material

            var pSetMat3      = BbPropertySet.Create(@"AISC_EM11_Pset_MaterialProperty");
            var materialAngle = BbMaterial.Create("ASTM A992", pSetMat3, "materialID003",
                                                  "materialCert003", "materialGrade003", "materialType003");

            materialAngle.AssociateTo(angle);
            //Finish/treatment
            //var paintAngle = BbPaintFinish.Create("angle blasted", "BLASTED", angle);
            //angle.AddPaintFinish(paintAngle);
            //paintAngle.AddToElement(angle);
            var pSetSTAngle01  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintAnglePset = BbSurfaceTreatmentProperty.Create(pSetSTAngle01, new List <string> {
                "Galvanized"
            });

            paintAnglePset.AssignTo(angle);

            //Feature
            //DrillHoles.Create(angle, Coordinate2D.Create(100, -5), 15, HoleLocation.Bottom, false);
            //DrillHoles.Create(angle, Coordinate2D.Create(300, 10), 20, HoleLocation.Bottom, false);
            var bHoleAngle01 = BbDrillHoles.Create(angle, BbCoordinate2D.Create(80, 9.5), 15, SemHoleLocation.Right, false);
            var bHoleAngle02 = BbDrillHoles.Create(angle, BbCoordinate2D.Create(280, 9.5), 20, SemHoleLocation.Right, false);
            //Clip Angle1 Bolt Hole properties
            var pSetAngleBH01      = BbPropertySet.Create(@"AISC_EM11_Pset_BoltHole");
            var boltHoleAnglePset1 = BbBoltHoleProperties.Create(pSetAngleBH01, "Drilling", "Top", "No design constraint", "Tapped Hole", 30, false, 0);

            boltHoleAnglePset1.AssignTo(bHoleAngle01);
            boltHoleAnglePset1.AssignTo(bHoleAngle02);


            var derived = BbDerivedProfile.Create(aProfile, true, true);
            var angle2  = BbClipAngle.Create("a00103",
                                             "angle", derived, 360,
                                             //BbCoordinate3D.Create(5898.5, -90.3, -180 - 254),
                                             BbCoordinate3D.Create(-90.3, -180, 5898.5),
                                             //BbDirection3D.ZAxis, BbDirection3D.XAxis2D,
                                             BbHeaderSetting.Setting3D.YAxis, BbHeaderSetting.Setting3D.Axis,
                                             mainPart);

            //Clip angle 2 properties
            //Identification
            var angleIdentity2 = BbPieceIdentity.Create("indMark007", "pieceMark007", "prelimMark007", "barcode123456897", false);

            angleIdentity2.AssignTo(angle2);
            //Status
            statusAngle01.AssignTo(angle2);
            //Version
            versionAngle01.AssignTo(angle2);
            //Tolerance
            toleranceAngle01.AssignTo(angle2);
            //Quantity
            qAngle.Add(angle2);
            //Material
            materialAngle.AssociateTo(angle2);
            //Finish/treatment
            //angle2.AddPaintFinish(paintAngle);
            //paintAngle.AddToOtherElement(angle2);
            //paintAnglePset.AssignTo(angle2);

            //DrillHoles.Create(angle2, Coordinate2D.Create(100, -5), 15, HoleLocation.Top, false);
            //DrillHoles.Create(angle2, Coordinate2D.Create(300, 10), 20, HoleLocation.Top, false);
            var bHoleAngle03 = BbDrillHoles.Create(angle2, BbCoordinate2D.Create(80, -9.5), 15, SemHoleLocation.Right, false);
            var bHoleAngle04 = BbDrillHoles.Create(angle2, BbCoordinate2D.Create(280, -9.5), 20, SemHoleLocation.Right, false);

            //Clip Angle2 Bolt Hole properties
            boltHoleAnglePset1.AssignTo(bHoleAngle03);
            boltHoleAnglePset1.AssignTo(bHoleAngle04);



            var w1 = BbWeld.Create(mainPart, angle);

            //var w1 = BbWeld.Create("Tee Joint", mainPart, angle);
            //var w2 = Weld.Create("Tee Joint", mainPart, angle2);
            w1.AddWeldingPath(curveGeometry, BbCoordinate3D.Create(0.0, 0.0, 0.0));

            var pSetw1 = BbPropertySet.Create(@"AISC_EM11_Pset_Weld");

            w1.AddProperties(pSetw1, "weld id", "weld description", "wps code", "category", "weld grade", 100, false);
            w1.AddProperties(pSetw1, "weld type1", "weld type2", "weld surface1", "weld surface 2", 123, "weld process",
                             1, 2, 3, 4, 5, 6, 7, 8, false, false);

            pSetw1.AssignTo(w1);


            var wc000          = BbCoordinate3D.Create(5898.5, 0, 0);
            var wc001          = BbCoordinate3D.Create(5898.5, 0, 200);
            var ccurve         = BbPolyline3D.Create(new BbCoordinate3D[] { wc000, wc001 });
            var ccurveGeometry = BbCurveGeometry.Create(ccurve);

            var boltAss = BbBoltAssembly.Create(mainPart, angle, ccurveGeometry, BbCoordinate3D.Create(1200, 60, 0));

            var nut = BbNut.Create(boltAss);

            var nutPSetw1 = BbPropertySet.Create(@"AISC_EM11_Pset_Nut");

            nut.AddProperties(nutPSetw1, "nut standard", "nut type", 5, 3, false);
            nutPSetw1.AssignTo(nut);

            var washer1 = BbWasher.Create(boltAss);

            var washerPSetw1 = BbPropertySet.Create(@"AISC_EM11_Pset_Washer");

            nut.AddProperties(washerPSetw1, "washer standard", "washer type", 5, 2, false);
            washerPSetw1.AssignTo(washer1);

            var washer2      = BbWasher.Create(boltAss);
            var washerPSetw2 = BbPropertySet.Create(@"AISC_EM11_Pset_Washer");

            nut.AddProperties(washerPSetw2, "washer standard", "washer type", 5, 1, true);
            washerPSetw2.AssignTo(washer2);

            //w1.AddProperties();


            //var wtype = SemWeldType.Create("Tee Joint", "tj0001");
            //wtype.Defines(w1);
            //wtype.Defines(w2);


            ////var derived2 = DerivedProfile.Create(aProfile, true, false);
            ////var angle3 = SteelPiece.Create("a00104",
            ////    "angle", derived2, 400,
            ////    Coordinate3D.Create(101.5, -90.3, -200 - 254), Direction3D.ZAxis, Direction3D.XAxis2D, assembly,
            ////    typeof(IfcDiscreteAccessory));



            //////DrillHoles.Create(angle3, Coordinate2D.Create(100, 5), 15, HoleLocation.Top, false);
            //////DrillHoles.Create(angle3, Coordinate2D.Create(300, 5), 15, HoleLocation.Top, false);
            ////DrillHoles.Create(angle3, Coordinate2D.Create(100, -10), 15, HoleLocation.Left, false);
            ////DrillHoles.Create(angle3, Coordinate2D.Create(300, -10), 15, HoleLocation.Left, false);

            ////var angle4 = SteelPiece.Create("a00105",
            ////    "angle",  aProfile, 400,
            ////    Coordinate3D.Create(101.5, 90.3, -200 - 254), Direction3D.ZAxis, Direction3D.XAxis2D, assembly,
            ////    typeof(IfcDiscreteAccessory));

            //////DrillHoles.Create(angle4, Coordinate2D.Create(100, 5), 15, HoleLocation.Bottom, false);
            //////DrillHoles.Create(angle4, Coordinate2D.Create(300, 5), 15, HoleLocation.Bottom, false);
            ////DrillHoles.Create(angle4, Coordinate2D.Create(100, 10), 15, HoleLocation.Left, false);
            ////DrillHoles.Create(angle4, Coordinate2D.Create(300, 10), 15, HoleLocation.Left, false);



            //Clip angle for column2----------------------------------------------------------------------------------

            var derived3 = BbDerivedProfile.Create(aProfile, true, false);
            var angle3   = BbClipAngle.Create(
                "a00103",
                "angle",
                derived3, 360,
                BbCoordinate3D.Create(-90.3, -180, 5898.5 - 5798.5),
                BbHeaderSetting.Setting3D.YAxis, BbHeaderSetting.Setting3D.Axis,
                mainPart
                );

            //Clip angle 3 properties
            //Identification
            var angleIdentity3 = BbPieceIdentity.Create("indMark008", "pieceMark008", "prelimMark008", "barcode123456898", false);

            angleIdentity3.AssignTo(angle3);
            //Status
            statusAngle01.AssignTo(angle3);
            //Version
            versionAngle01.AssignTo(angle3);
            //Tolerance
            toleranceAngle01.AssignTo(angle3);
            //Quantity
            qAngle.Add(angle3);
            //Material
            materialAngle.AssociateTo(angle3);
            //Finish/treatment
            //angle3.AddPaintFinish(paintAngle);
            //paintAngle.AddToOtherElement(angle3);
            //paintAnglePset.AssignTo(angle3);

            var bHoleAngle05 = BbDrillHoles.Create(angle3, BbCoordinate2D.Create(80, -10), 15, SemHoleLocation.Left, false);
            var bHoleAngle06 = BbDrillHoles.Create(angle3, BbCoordinate2D.Create(280, -10), 15, SemHoleLocation.Left, false);

            //Clip Angle3 Bolt Hole properties
            boltHoleAnglePset1.AssignTo(bHoleAngle05);
            boltHoleAnglePset1.AssignTo(bHoleAngle06);


            var derived4 = BbDerivedProfile.Create(aProfile, false, false);
            var angle4   = BbClipAngle.Create(
                "a00104",
                "angle",
                derived4, 360,
                BbCoordinate3D.Create(90.3, -180, 5898.5 - 5798.5),
                BbHeaderSetting.Setting3D.YAxis, BbHeaderSetting.Setting3D.Axis,
                mainPart
                );

            //Clip angle 4 properties
            //Identification
            var angleIdentity4 = BbPieceIdentity.Create("indMark009", "pieceMark009", "prelimMark009", "barcode123456899", false);

            angleIdentity4.AssignTo(angle4);
            //Status
            statusAngle01.AssignTo(angle4);
            //Version
            versionAngle01.AssignTo(angle4);
            //Tolerance
            toleranceAngle01.AssignTo(angle4);
            //Quantity
            qAngle.Add(angle4);
            //Material
            materialAngle.AssociateTo(angle4);
            //Finish/treatment
            //angle4.AddPaintFinish(paintAngle);
            //paintAngle.AddToOtherElement(angle4);
            //paintAnglePset.AssignTo(angle4);

            var bHoleAngle07 = BbDrillHoles.Create(angle4, BbCoordinate2D.Create(80, 10), 15, SemHoleLocation.Left, false);
            var bHoleAngle08 = BbDrillHoles.Create(angle4, BbCoordinate2D.Create(280, 10), 15, SemHoleLocation.Left, false);

            boltHoleAnglePset1.AssignTo(bHoleAngle07);
            boltHoleAnglePset1.AssignTo(bHoleAngle08);

            // welding column 2 & beam with angle 3,4//DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD


            // Assembly 2- Column1-------------------------------------------------------------------------------------
            var assembly2 = BbAssembly.Create(
                "assid003",
                "Steel Assembly",
                "ASS02", "client_marker2",
                "prelim_marker2",
                "ship_mark2",
                "202301123433",
                floor,
                BbCoordinate3D.Create(6014.3, 0, 0),
                BbHeaderSetting.Setting3D.ZAxis,
                BbHeaderSetting.Setting3D.XAxis);

            // assembly 2 properties
            //Quantity
            var qAssemCol1 = BbQuantityRequired.Create();

            qAssemCol1.Add(assembly2);
            //Finish/tearment
            //var paintAssem2 = BbPaintFinish.Create("Assy gal", "GALVANIZED",assembly2);
            //assembly2.AddPaintFinish(paintAssem2);
            //paintAssem2.AddToElement(assembly2);

            var pSetAssemSTr02  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintAssem2Pset = BbSurfaceTreatmentProperty.Create(pSetAssemSTr02, new List <string> {
                "Galvanized"
            });

            paintAssem2Pset.AssignTo(assembly2);
            //Scheduling
            var pSetAssemSc02 = BbPropertySet.Create(@"AISC_EM11_Pset_Schedule");
            var AssemSch02    = BbSchedule.Create(pSetAssemSc02, "seq01", "seqLevel 01", DateTime.Now);

            AssemSch02.AssignTo(assembly2);
            //Status
            var pSetAssemSt02 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var AssemStat02   = BbStatus.Create(pSetAssemSt02, "Default", "Default", true);

            AssemStat02.AssignTo(assembly2);
            //Drawing number
            var pSetAssemDN02     = BbPropertySet.Create(@"AISC_EM11_Pset_DrawingNumber");
            var DnumberAssem2Pset = BbDrawingNumber.Create(pSetAssemDN02, new List <string> {
                "DR001PH1006", "DR001PH1005"
            });

            DnumberAssem2Pset.AssignTo(assembly2);
            //Version
            var pSetAssemVr02  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionAssem02 = BbVersion.Create(pSetAssemVr02, "versionAssem02");

            versionAssem02.AssignTo(assembly2);

            //Main Piece 2- Column1
            var mainPart2 = BbMainPiece.Create(
                "c00102",
                "main piece",
                profile, 6000,
                BbHeaderSetting.Setting3D.DefaultOrigin,
                BbHeaderSetting.Setting3D.ZAxis,
                BbHeaderSetting.Setting3D.XAxis,
                assembly2);

            // Column1 properties
            //Identification
            var pieceIdCol01 = BbPieceIdentity.Create("indMark010", "pieceMark010", "prelimMark010", "barcode123456880", true);

            pieceIdCol01.AssignTo(mainPart2);
            //Status
            var pSetColSt01 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var statusCol01 = BbStatus.Create(pSetColSt01, "ReadyForProcurement", "Default", true);

            statusCol01.AssignTo(mainPart2);
            //Version
            var pSetColVr01  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionCol01 = BbVersion.Create(pSetColVr01, "versionCol001");

            versionCol01.AssignTo(mainPart2);
            //Tolerance
            var pSetColLy01    = BbPropertySet.Create(@"AISC_EM11_Pset_ToleranceForLayout");
            var toleranceCol01 = BbLayoutTolerance.Create(pSetColLy01, 0.002);

            toleranceCol01.AssignTo(mainPart2);
            //Quantity
            var qPieceCol = BbQuantityRequired.Create();

            qPieceCol.Add(mainPart2);
            //Material

            var pSetMat4 = BbPropertySet.Create(@"AISC_EM11_Pset_MaterialProperty");

            var materialCol1 = BbMaterial.Create("ASTM A992", pSetMat4, "materialID004",
                                                 "materialCert004", "materialGrade004", "materialType004");

            materialCol1.AssociateTo(mainPart2);
            //Finish/treatment
            //var paintCol1 = BbPaintFinish.Create("paint col", "PAINTED", mainPart2);
            //mainPart2.AddPaintFinish(paintCol1);
            //paintCol1.AddToElement(mainPart2);

            var pSetColST01  = BbPropertySet.Create(@"AISC_EM11_Pset_SurfaceTreatment");
            var paintColPset = BbSurfaceTreatmentProperty.Create(pSetColST01, new List <string> {
                "Blast"
            });

            paintColPset.AssignTo(mainPart2);
            //Castellation
            //var pSetCt02 = BbPropertySet.Create(@"AISC_EM11_Pset_Castellation");
            //var castellation2 = BbCastellation.Create(pSetCt02, "Circular", 0.002, 0.002, 0.001, 0.002, 0.01, 0.001);
            //castellation2.AssignTo(mainPart2);

            //Features
            var bHoleCol01 = BbDrillHoles.Create(mainPart2, BbCoordinate2D.Create(6000 - 508 / 2 - 100, 100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol02 = BbDrillHoles.Create(mainPart2, BbCoordinate2D.Create(6000 - 508 / 2 + 100, 100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol03 = BbDrillHoles.Create(mainPart2, BbCoordinate2D.Create(6000 - 508 / 2 - 100, -100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol04 = BbDrillHoles.Create(mainPart2, BbCoordinate2D.Create(6000 - 508 / 2 + 100, -100), 15, SemHoleLocation.Web,
                                                 false);

            var pSetColBH01      = BbPropertySet.Create(@"AISC_EM11_Pset_BoltHole");
            var boltHoleColPset1 = BbBoltHoleProperties.Create(pSetColBH01, "Drilling", "Top", "No design constraint", "Tapped Hole", 20, false, 0);

            boltHoleColPset1.AssignTo(bHoleCol01);
            boltHoleColPset1.AssignTo(bHoleCol02);
            boltHoleColPset1.AssignTo(bHoleCol03);
            boltHoleColPset1.AssignTo(bHoleCol04);

            BbSlottedHole.Create(mainPart2, BbCoordinate2D.Create(5000, 50), 100, 30, BbDirection2D.Create(0.9, 0.3),
                                 SemHoleLocation.Web, true);
            //Slotted Hole properties


            // welding colum 1 with angle//DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD

            //SemConnectedElements.Create(assembly, assembly2);

            ///////////////////////////////////////////weld

            //var wp = BbWeldProperties.Create(10, 14);
            //wp.AssignTo(w1);
            //wp.AssignTo(w2);


            // Assembly 3- Column2----------------------------------------------------------------------------------------
            var assembly3 = BbAssembly.Create(
                "assid003", "Steel Assembly", "ASS02", "client_marker3", "prelim_marker3", "ship_mark3", "302301123425",
                floor,
                BbCoordinate3D.Create(-14.3, 0, 0), BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis);

            // Assembly 3 properties
            //Quantity
            qAssemCol1.Add(assembly3);
            //Finish/tearment
            //assembly3.AddPaintFinish(paintAssem2);
            //paintAssem2.AddToOtherElement(assembly3);

            //paintAssem2Pset.AssignTo(assembly3);
            //Scheduling
            AssemSch02.AssignTo(assembly3);
            //Status
            AssemStat02.AssignTo(assembly3);
            //Drawing number
            var pSetAssemDN03     = BbPropertySet.Create(@"AISC_EM11_Pset_DrawingNumber");
            var DnumberAssem3Pset = BbDrawingNumber.Create(pSetAssemDN03, new List <string> {
                "DR001PH1006", "DR001PH1005", "DR001PH1008"
            });

            DnumberAssem3Pset.AssignTo(assembly3);
            //Version
            versionAssem02.AssignTo(assembly3);

            //Main Piece 3- Column 2
            var mainPart3 = BbMainPiece.Create("c20010",
                                               "main piece", profile, 6000,
                                               BbHeaderSetting.Setting3D.DefaultOrigin, BbHeaderSetting.Setting3D.ZAxis, BbHeaderSetting.Setting3D.XAxis, assembly3);


            //Column2 properties
            //Identification
            var pieceIdCol02 = BbPieceIdentity.Create("indMark011", "pieceMark011", "prelimMark011", "barcode123456881", true);

            pieceIdCol02.AssignTo(mainPart3);
            //Status
            var pSetColSt02 = BbPropertySet.Create(@"AISC_EM11_Pset_StatusInformation");
            var statusCol02 = BbStatus.Create(pSetColSt02, "ReadyForMill", "Default", true);

            statusCol02.AssignTo(mainPart3);
            //Version
            var pSetColVr02  = BbPropertySet.Create(@"AISC_EM11_Pset_VersionInformation");
            var versionCol02 = BbVersion.Create(pSetColVr02, "versionCol002");

            versionCol02.AssignTo(mainPart3);
            //Tolerance
            toleranceCol01.AssignTo(mainPart3);
            //Quantity
            qPieceCol.Add(mainPart3);
            //Material
            materialCol1.AssociateTo(mainPart3);
            //Finish/treatment
            //mainPart3.AddPaintFinish(paintCol1);
            //paintCol1.AddToOtherElement(mainPart3);
            //paintColPset.AssignTo(mainPart3);

            //Castellation- not required
            //var pSetCt02 = BbPropertySet.Create(@"AISC_EM11_Pset_Castellation");
            //var castellation2 = BbCastellation.Create(pSetCt02, "Circular", 0.002, 0.002, 0.001, 0.002, 0.01, 0.001);
            //castellation2.AssignTo(mainPart2);


            // Column2 features
            var bHoleCol05 = BbDrillHoles.Create(mainPart3, BbCoordinate2D.Create(6000 - 508 / 2 - 100, 100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol06 = BbDrillHoles.Create(mainPart3, BbCoordinate2D.Create(6000 - 508 / 2 + 100, 100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol07 = BbDrillHoles.Create(mainPart3, BbCoordinate2D.Create(6000 - 508 / 2 - 100, -100), 15, SemHoleLocation.Web,
                                                 false);
            var bHoleCol08 = BbDrillHoles.Create(mainPart3, BbCoordinate2D.Create(6000 - 508 / 2 + 100, -100), 15, SemHoleLocation.Web,
                                                 false);

            boltHoleColPset1.AssignTo(bHoleCol05);
            boltHoleColPset1.AssignTo(bHoleCol06);
            boltHoleColPset1.AssignTo(bHoleCol07);
            boltHoleColPset1.AssignTo(bHoleCol08);


            return(BbInstanceDB.Write(filename));
        }
Exemplo n.º 18
0
 public static BbLocalPlacement3D Create(IfcLocalPlacement ifcLocalPlacement)
 {
     var placement3D = new BbLocalPlacement3D(ifcLocalPlacement);
     BbInstanceDB.AddToExport(placement3D);
     return placement3D;
 }
Exemplo n.º 19
0
 BbLocalPlacement3D(BbLocalPlacement3D placementRelTo)
     : this(placementRelTo, null)
 {
 }
Exemplo n.º 20
0
 public static BbLocalPlacement3D Create(BbLocalPlacement3D placementRelTo)
 {
     var placement3D = new BbLocalPlacement3D(placementRelTo);
     BbInstanceDB.AddToExport(placement3D);
     return placement3D;
 }
Exemplo n.º 21
0
 public static BbLocalPlacement3D Create(BbLocalPlacement3D placementRelTo, BbPosition3D relativePlacement)
 {
     var placement3D = new BbLocalPlacement3D(placementRelTo, relativePlacement);
     BbInstanceDB.AddToExport(placement3D);
     return placement3D;
 }
Exemplo n.º 22
0
        BbSkewedEnd(
            BbElement hostElement,
            BbPosition3D pos)
        {
            var mainPart = hostElement as BbPiece;

            if (mainPart == null)
            {
                return;
            }

            var width = mainPart.Length > mainPart.Profile.Width ? mainPart.Length : mainPart.Profile.Width;

            width = width * 100;
            var depth = mainPart.Length > mainPart.Profile.Depth ? mainPart.Length : mainPart.Profile.Depth;

            depth = depth * 100;
            var profile = BbNamedRectangleProfile.Create(width, depth);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostElement.ObjectBbLocalPlacement, pos);



            //Direction3D exDir = Direction3D.Create(new[] {pos.Axis.X, pos.Axis.Y, pos.Axis.Z});

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                mainPart.Length);


            //IfcHalfSpaceSolid ifcHalfSpaceSolid = new IfcHalfSpaceSolid
            //    {
            //        BaseSurface = new IfcPlane
            //            {
            //                Position = pos.IfcAxis2Placement3D,
            //            },
            //            AgreementFlag = true,

            //    };

            //IfcShapeRepresentation ifcShapeRepresentation = new IfcShapeRepresentation
            //{
            //    ContextOfItems = HeaderSetting.Setting3D.GeometricRepresentationContext,
            //    RepresentationIdentifier = "Body",
            //    RepresentationType = "SweptSolid",
            //    //RepresentationIdentifier = "Body",
            //    //RepresentationType = "SolidModel",
            //    Items = new List<IfcRepresentationItem>(),
            //};
            //ifcShapeRepresentation.Items.Add(ifcHalfSpaceSolid);

            //IfcProductDefinitionShape ifcProductDefinitionShape = new IfcProductDefinitionShape
            //{
            //    // Name=
            //    // Description =
            //    Representations = new List<IfcRepresentation>(),
            //};
            //ifcProductDefinitionShape.Representations.Add(ifcShapeRepresentation);

            _ifcOpeningElement = new IfcOpeningElement
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = hostElement.IfcObject.OwnerHistory,
                // Name =
                // Description =
                ObjectType      = "Opening",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = bbExtrudedGeometry.IfcProductDefinitionShape,
                //Representation = ifcProductDefinitionShape,
            };

            _ifcRelVoidsElement = new IfcRelVoidsElement
            {
                GlobalId                = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory            = hostElement.IfcObject.OwnerHistory,
                Name                    = "Skewed End",
                RelatingBuildingElement = hostElement.IfcObject as IfcElement,
                RelatedOpeningElement   = _ifcOpeningElement,
            };
        }
Exemplo n.º 23
0
        protected BbAssembly(
            string assemblyId,
            string assemblyName,
            string assemblyMark,
            string clientMark,
            string prelimMark,
            string shippingMark,
            string barCode,
            BbSpatialElement floor,
            BbCoordinate3D position,
            BbDirection3D zAxis,
            BbDirection3D xAxis
            )
        {
            //AssemblyName = assemblyName;
            //AssemblyMark = assemblyMark;

            var pos = BbPosition3D.Create(position, zAxis, xAxis);

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                floor.ObjectBbLocalPlacement, pos);

            _ifcElementAssembly = new IfcElementAssembly
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = floor.IfcSpatialStructureElement.OwnerHistory,
                Name         = assemblyName,
                Description  = null,
                ObjectType   = null,

                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = null,
                Tag             = assemblyId,
                AssemblyPlace   = IfcAssemblyPlaceEnum.NOTDEFINED,
                PredefinedType  = IfcElementAssemblyTypeEnum.RIGID_FRAME
            };


            BbAssemblyIdentity = BbAssemblyIdentity.Create(
                //				assemblyName,
                assemblyMark, clientMark, prelimMark, shippingMark,
                barCode);
            BbAssemblyIdentity.AssignTo(this);

            AddToSpatialElement(floor);

            // var relContaineds = EarlyBindingInstanceModel.GetDataByType("IfcRelContainedInSpatialStructure");

            //var thecontained = from y in ( from x in relContaineds
            //                   select x.Value as IfcRelContainedInSpatialStructure)
            //                       where y.;

            //var b = BbInstanceDB.GetTypedList(typeof(BbAssembly));


            //if (b == null)
            //{
            //    IfcRelContainedInSpatialStructure = new IfcRelContainedInSpatialStructure
            //    {
            //        GlobalId = IfcGloballyUniqueId.NewGuid(),
            //        OwnerHistory = _ifcElementAssembly.OwnerHistory,
            //        RelatingStructure = floor.IfcSpatialStructureElement,
            //        RelatedElements = new List<IfcProduct>(),
            //    };
            //}
            //else
            //{

            //    var otherAssemblies = (from x in b.OfType<BbAssembly>()

            //                           select x).ToList();

            //    //var a = otherAssemblies as IList<BbAssembly>;

            //    var other = (from x in otherAssemblies
            //                 where x.BbSpatialElement.IfcSpatialStructureElement.Name
            //                 == BbSpatialElement.IfcSpatialStructureElement.Name
            //                 select x).First();
            //    if (other == null)
            //    {
            //        IfcRelContainedInSpatialStructure = new IfcRelContainedInSpatialStructure
            //        {
            //            GlobalId = IfcGloballyUniqueId.NewGuid(),
            //            OwnerHistory = _ifcElementAssembly.OwnerHistory,
            //            RelatingStructure = BbSpatialElement.IfcSpatialStructureElement,
            //            RelatedElements = new List<IfcProduct>(),
            //        };
            //    }
            //    else
            //    {
            //        IfcRelContainedInSpatialStructure = other.IfcRelContainedInSpatialStructure;
            //    }
            //}

            //IfcRelContainedInSpatialStructure.RelatedElements.Add(_ifcElementAssembly);
        }
Exemplo n.º 24
0
        BbCutCope(
            BbElement hostElement,
            double copeWidth,
            double copeDepth,
            double copeRadius,
            SemCopeLocation copeLocation)
        {
            BbCopeProfile profile = BbCopeProfile.Create(copeWidth, copeDepth, copeRadius, copeLocation);

            var mainPart = hostElement as BbPiece;

            if (mainPart == null)
            {
                return;
            }

            BbPosition3D pos;

            switch (copeLocation)
            {
            case SemCopeLocation.BottomLeft:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(new double[] {
                    mainPart.Profile.Width / 2,
                    -mainPart.Profile.Depth / 2,
                    0
                }),
                    BbHeaderSetting.Setting3D.XAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                break;

            case SemCopeLocation.BottomRight:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(new double[] {
                    mainPart.Profile.Width / 2,
                    -mainPart.Profile.Depth / 2,
                    mainPart.Length
                }),
                    BbHeaderSetting.Setting3D.XAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                break;

            case SemCopeLocation.TopRight:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(new double[] {
                    mainPart.Profile.Width / 2,
                    mainPart.Profile.Depth / 2,
                    mainPart.Length
                }),
                    BbHeaderSetting.Setting3D.XAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                break;

            default:     // TopLeft
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(new double[] {
                    mainPart.Profile.Width / 2,
                    mainPart.Profile.Depth / 2,
                    0
                }),
                    BbHeaderSetting.Setting3D.XAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                break;
            }

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostElement.ObjectBbLocalPlacement, pos);

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                mainPart.Profile.Width);

            _ifcOpeningElement = new IfcOpeningElement
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = hostElement.IfcObject.OwnerHistory,
                // Name =
                // Description =
                ObjectType      = "Opening",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = bbExtrudedGeometry.IfcProductDefinitionShape,
            };

            _ifcRelVoidsElement = new IfcRelVoidsElement
            {
                GlobalId                = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory            = hostElement.IfcObject.OwnerHistory,
                Name                    = "Cope",
                RelatingBuildingElement = hostElement.IfcObject as IfcElement,
                RelatedOpeningElement   = _ifcOpeningElement,
            };
        }
Exemplo n.º 25
0
 BbLocalPlacement3D(BbLocalPlacement3D placementRelTo)
     : this(placementRelTo, null)
 {
 }
Exemplo n.º 26
0
        protected BbOpening(
            BbElement hostElement,
            BbCoordinate2D position,
            BbProfile profile,
            SemHoleLocation location,
            bool through,
            string type
            )
        {
            var mainPart = hostElement as BbPiece;

            if (mainPart == null)
            {
                return;
            }


            double       thickness;
            BbPosition3D pos;

            // x direction follows extrusion direction
            // extrude origin  projected to bottom or left becomes the origin

            switch (location)
            {
            case SemHoleLocation.Left:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(
                        -(mainPart.Profile.Width / 2),
                        position.Y,
                        position.X),
                    BbHeaderSetting.Setting3D.XAxis,
                    BbHeaderSetting.Setting3D.ZAxis);
                if (through)
                {
                    thickness = mainPart.Profile.Width;
                }
                else
                {
                    thickness = mainPart.Profile.Width / 2;
                }
                break;

            case SemHoleLocation.Right:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(
                        (mainPart.Profile.Width / 2),
                        position.Y,
                        position.X),
                    BbHeaderSetting.Setting3D.XAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                if (through)
                {
                    thickness = mainPart.Profile.Width;
                }
                else
                {
                    thickness = mainPart.Profile.Width / 2;
                }
                break;

            case SemHoleLocation.Web:
                if (through)
                {
                    pos = BbPosition3D.Create(
                        BbCoordinate3D.Create(
                            (mainPart.Profile.Width / 2),
                            position.Y,
                            position.X
                            ),
                        BbHeaderSetting.Setting3D.XAxisMinus,
                        BbHeaderSetting.Setting3D.ZAxis);
                    thickness = mainPart.Profile.Width;
                }
                else
                {
                    pos = BbPosition3D.Create(
                        BbCoordinate3D.Create(
                            (mainPart.Profile.Width / 4),
                            position.Y,
                            position.X
                            ),
                        BbHeaderSetting.Setting3D.XAxisMinus,
                        BbHeaderSetting.Setting3D.ZAxis);
                    thickness = mainPart.Profile.Width / 2;
                }
                break;

            case SemHoleLocation.Bottom:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(
                        position.Y,
                        -(mainPart.Profile.Depth / 2),
                        position.X
                        ),
                    BbHeaderSetting.Setting3D.YAxis,
                    BbHeaderSetting.Setting3D.ZAxis);
                if (through)
                {
                    thickness = mainPart.Profile.Depth;
                }
                else
                {
                    thickness = mainPart.Profile.Depth / 2;
                }
                break;

            case SemHoleLocation.Top:
            default:
                pos = BbPosition3D.Create(
                    BbCoordinate3D.Create(
                        position.Y,
                        (mainPart.Profile.Depth / 2),
                        position.X
                        ),
                    BbHeaderSetting.Setting3D.YAxisMinus,
                    BbHeaderSetting.Setting3D.ZAxis);
                if (through)
                {
                    thickness = mainPart.Profile.Depth;
                }
                else
                {
                    thickness = mainPart.Profile.Depth / 2;
                }
                break;
            }

            ObjectBbLocalPlacement = BbLocalPlacement3D.Create(
                hostElement.ObjectBbLocalPlacement, pos);

            BbExtrudedGeometry bbExtrudedGeometry = BbExtrudedGeometry.Create(
                profile,
                BbHeaderSetting.Setting3D.DefaultBbPosition3D,
                BbHeaderSetting.Setting3D.ZAxis,
                thickness);

            _ifcOpeningElement = new IfcOpeningElement
            {
                GlobalId     = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory = hostElement.IfcObject.OwnerHistory,
                // Name =
                // Description =
                ObjectType      = "Opening",
                ObjectPlacement = ObjectBbLocalPlacement.IfcLocalPlacement,
                Representation  = bbExtrudedGeometry.IfcProductDefinitionShape,
            };

            _ifcRelVoidsElement = new IfcRelVoidsElement
            {
                GlobalId                = IfcGloballyUniqueId.NewGuid(),
                OwnerHistory            = hostElement.IfcObject.OwnerHistory,
                Name                    = type,
                RelatingBuildingElement = hostElement.IfcObject as IfcElement,
                RelatedOpeningElement   = _ifcOpeningElement,
            };
        }
Exemplo n.º 27
0
 public void AddGeometricRepresentation(BbElement hostElement, BbSurfaceGeometry surfaceGeometry,
     BbLocalPlacement3D localPlacement3D)
 {
     BbSurfaceGeometry = surfaceGeometry;
     BbLocalPlacement3D = localPlacement3D;
 }
Exemplo n.º 28
0
 public void AddGeometricRepresentation(BbElement hostElement, BbSurfaceGeometry surfaceGeometry,
                                        BbLocalPlacement3D localPlacement3D)
 {
     BbSurfaceGeometry  = surfaceGeometry;
     BbLocalPlacement3D = localPlacement3D;
 }