public void writeGCode(bool liftHeadIfNeeded, int layerThickness)
{
GCodePathConfig lastConfig = null;
int extruderIndex = gcode.getExtruderIndex();
for (int pathIndex = 0; pathIndex < paths.Count; pathIndex++)
{
GCodePath path = paths[pathIndex];
if (extruderIndex != path.extruderIndex)
{
extruderIndex = path.extruderIndex;
gcode.switchExtruder(extruderIndex);
}
else if (path.Retract)
{
gcode.writeRetraction();
}
if (path.config != travelConfig && lastConfig != path.config)
{
gcode.writeComment("TYPE:{0}".FormatWith(path.config.name));
lastConfig = path.config;
}
int speed = path.config.speed;
if (path.config.lineWidth != 0)
{
// Only apply the extrudeSpeedFactor to extrusion moves
speed = speed * extrudeSpeedFactor / 100;
}
else
{
speed = speed * travelSpeedFactor / 100;
}
if (path.points.Count == 1 &&
path.config != travelConfig &&
(gcode.getPositionXY() - path.points[0]).ShorterThen(path.config.lineWidth * 2))
{
//Check for lots of small moves and combine them into one large line
IntPoint nextPosition = path.points[0];
int i = pathIndex + 1;
while (i < paths.Count && paths[i].points.Count == 1 && (nextPosition - paths[i].points[0]).ShorterThen(path.config.lineWidth * 2))
{
nextPosition = paths[i].points[0];
i++;
}
if (paths[i - 1].config == travelConfig)
{
i--;
}
if (i > pathIndex + 2)
{
nextPosition = gcode.getPositionXY();
for (int x = pathIndex; x < i - 1; x += 2)
{
long oldLen = (nextPosition - paths[x].points[0]).vSize();
IntPoint newPoint = (paths[x].points[0] + paths[x + 1].points[0]) / 2;
long newLen = (gcode.getPositionXY() - newPoint).vSize();
if (newLen > 0)
{
gcode.writeMove(newPoint, speed, (int)(path.config.lineWidth * oldLen / newLen));
}
nextPosition = paths[x + 1].points[0];
}
gcode.writeMove(paths[i - 1].points[0], speed, path.config.lineWidth);
pathIndex = i - 1;
continue;
}
}
bool spiralize = path.config.spiralize;
if (spiralize)
{
//Check if we are the last spiralize path in the list, if not, do not spiralize.
for (int m = pathIndex + 1; m < paths.Count; m++)
{
if (paths[m].config.spiralize)
{
spiralize = false;
}
}
}
if (spiralize)
{
//If we need to spiralize then raise the head slowly by 1 layer as this path progresses.
double totalLength = 0;
int z = gcode.getPositionZ();
IntPoint currentPosition = gcode.getPositionXY();
for (int pointIndex = 0; pointIndex < path.points.Count; pointIndex++)
{
IntPoint nextPosition = path.points[pointIndex];
totalLength += (currentPosition - nextPosition).LengthMm();
currentPosition = nextPosition;
}
double length = 0.0;
currentPosition = gcode.getPositionXY();
for (int i = 0; i < path.points.Count; i++)
{
IntPoint nextPosition = path.points[i];
length += (currentPosition - nextPosition).LengthMm();
currentPosition = nextPosition;
gcode.setZ((int)(z + layerThickness * length / totalLength + .5));
gcode.writeMove(path.points[i], speed, path.config.lineWidth);
}
}
else
{
for (int pointIndex = 0; pointIndex < path.points.Count; pointIndex++)
{
gcode.writeMove(path.points[pointIndex], speed, path.config.lineWidth);
}
}
}
gcode.updateTotalPrintTime();
if (liftHeadIfNeeded && extraTime > 0.0)
{
gcode.writeComment("Small layer, adding delay of {0}".FormatWith(extraTime));
gcode.writeRetraction();
gcode.setZ(gcode.getPositionZ() + 3000);
gcode.writeMove(gcode.getPositionXY(), travelConfig.speed, 0);
gcode.writeMove(gcode.getPositionXY() - new IntPoint(-20000, 0), travelConfig.speed, 0);
gcode.writeDelay(extraTime);
}
}
private void writeGCode(SliceDataStorage storage)
{
gcode.WriteComment("filamentDiameter = {0}".FormatWith(config.filamentDiameter));
gcode.WriteComment("extrusionWidth = {0}".FormatWith(config.extrusionWidth));
gcode.WriteComment("firstLayerExtrusionWidth = {0}".FormatWith(config.firstLayerExtrusionWidth));
gcode.WriteComment("layerThickness = {0}".FormatWith(config.layerThickness));
gcode.WriteComment("firstLayerThickness = {0}".FormatWith(config.firstLayerThickness));
if (fileNumber == 1)
{
if (gcode.GetOutputType() == ConfigConstants.OUTPUT_TYPE.ULTIGCODE)
{
gcode.WriteComment("TYPE:UltiGCode");
gcode.WriteComment("TIME:<__TIME__>");
gcode.WriteComment("MATERIAL:<FILAMENT>");
gcode.WriteComment("MATERIAL2:<FILAMEN2>");
}
gcode.WriteCode(config.startCode);
if (gcode.GetOutputType() == ConfigConstants.OUTPUT_TYPE.BFB)
{
gcode.WriteComment("enable auto-retraction");
gcode.WriteLine("M227 S{0} P{1}".FormatWith(config.retractionOnTravel * 2560, config.retractionOnTravel * 2560));
}
}
else
{
gcode.WriteFanCommand(0);
gcode.ResetExtrusionValue();
gcode.WriteRetraction();
gcode.setZ(maxObjectHeight + 5000);
gcode.WriteMove(gcode.GetPositionXY(), config.travelSpeed, 0);
gcode.WriteMove(new IntPoint(storage.modelMin.x, storage.modelMin.y), config.travelSpeed, 0);
}
fileNumber++;
int totalLayers = storage.volumes[0].layers.Count;
// let's remove any of the layers on top that are empty
{
for (int layerIndex = totalLayers - 1; layerIndex >= 0; layerIndex--)
{
bool layerHasData = false;
foreach (SliceVolumeStorage currentVolume in storage.volumes)
{
SliceLayer currentLayer = currentVolume.layers[layerIndex];
for (int partIndex = 0; partIndex < currentVolume.layers[layerIndex].parts.Count; partIndex++)
{
SliceLayerPart currentPart = currentLayer.parts[partIndex];
if (currentPart.TotalOutline.Count > 0)
{
layerHasData = true;
break;
}
}
}
if (layerHasData)
{
break;
}
totalLayers--;
}
}
gcode.WriteComment("Layer count: {0}".FormatWith(totalLayers));
// keep the raft generation code inside of raft
Raft.GenerateRaftGCodeIfRequired(storage, config, gcode);
int volumeIndex = 0;
for (int layerIndex = 0; layerIndex < totalLayers; layerIndex++)
{
if (MatterSlice.Canceled)
{
return;
}
LogOutput.Log("Writing Layers {0}/{1}\n".FormatWith(layerIndex + 1, totalLayers));
LogOutput.logProgress("export", layerIndex + 1, totalLayers);
int extrusionWidth_um = config.extrusionWidth_um;
if (layerIndex == 0)
{
extrusionWidth_um = config.firstLayerExtrusionWidth_um;
}
if (layerIndex == 0)
{
skirtConfig.setData(config.firstLayerSpeed, extrusionWidth_um, "SKIRT");
inset0Config.setData(config.firstLayerSpeed, extrusionWidth_um, "WALL-OUTER");
insetXConfig.setData(config.firstLayerSpeed, extrusionWidth_um, "WALL-INNER");
fillConfig.setData(config.firstLayerSpeed, extrusionWidth_um, "FILL", false);
bridgConfig.setData(config.firstLayerSpeed, extrusionWidth_um, "BRIDGE");
supportNormalConfig.setData(config.firstLayerSpeed, config.supportExtrusionWidth_um, "SUPPORT");
supportInterfaceConfig.setData(config.firstLayerSpeed, config.extrusionWidth_um, "SUPPORT-INTERFACE");
}
else
{
skirtConfig.setData(config.insidePerimetersSpeed, extrusionWidth_um, "SKIRT");
inset0Config.setData(config.outsidePerimeterSpeed, extrusionWidth_um, "WALL-OUTER");
insetXConfig.setData(config.insidePerimetersSpeed, extrusionWidth_um, "WALL-INNER");
fillConfig.setData(config.infillSpeed, extrusionWidth_um, "FILL", false);
bridgConfig.setData(config.bridgeSpeed, extrusionWidth_um, "BRIDGE");
supportNormalConfig.setData(config.supportMaterialSpeed, config.supportExtrusionWidth_um, "SUPPORT");
supportInterfaceConfig.setData(config.supportMaterialSpeed, config.extrusionWidth_um, "SUPPORT-INTERFACE");
}
gcode.WriteComment("LAYER:{0}".FormatWith(layerIndex));
if (layerIndex == 0)
{
gcode.SetExtrusion(config.firstLayerThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
}
else
{
gcode.SetExtrusion(config.layerThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
}
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
// get the correct height for this layer
int z = config.firstLayerThickness_um + layerIndex * config.layerThickness_um;
if (config.enableRaft)
{
z += config.raftBaseThickness_um + config.raftInterfaceThicknes_um + config.raftSurfaceLayers * config.raftSurfaceThickness_um;
if (layerIndex == 0)
{
// We only raise the first layer of the print up by the air gap.
// To give it:
// Less press into the raft
// More time to cool
// more surface area to air while extruding
z += config.raftAirGap_um;
}
}
gcode.setZ(z);
// We only create the skirt if we are on layer 0 and the first volume and there is no raft.
if (layerIndex == 0 && volumeIndex == 0 && !Raft.ShouldGenerateRaft(config))
{
AddSkirtToGCode(storage, gcodeLayer, volumeIndex, layerIndex);
}
bool printSupportFirst = (storage.support.generated && config.supportExtruder >= 0 && config.supportExtruder == gcodeLayer.getExtruder());
if (printSupportFirst)
{
AddSupportToGCode(storage, gcodeLayer, layerIndex, config);
}
int fanSpeedPercent = GetFanSpeed(layerIndex, gcodeLayer);
for (int volumeCnt = 0; volumeCnt < storage.volumes.Count; volumeCnt++)
{
if (volumeCnt > 0)
{
volumeIndex = (volumeIndex + 1) % storage.volumes.Count;
}
AddVolumeLayerToGCode(storage, gcodeLayer, volumeIndex, layerIndex, extrusionWidth_um, fanSpeedPercent);
}
if (!printSupportFirst)
{
AddSupportToGCode(storage, gcodeLayer, layerIndex, config);
}
//Finish the layer by applying speed corrections for minimum layer times.
gcodeLayer.ForceMinimumLayerTime(config.minimumLayerTimeSeconds, config.minimumPrintingSpeed);
gcode.WriteFanCommand(fanSpeedPercent);
int currentLayerThickness_um = config.layerThickness_um;
if (layerIndex <= 0)
{
currentLayerThickness_um = config.firstLayerThickness_um;
}
gcodeLayer.WriteGCode(config.doCoolHeadLift, currentLayerThickness_um);
}
LogOutput.Log("Wrote layers in {0:0.00}s.\n".FormatWith(timeKeeper.Elapsed.Seconds));
timeKeeper.Restart();
gcode.TellFileSize();
gcode.WriteFanCommand(0);
//Store the object height for when we are printing multiple objects, as we need to clear every one of them when moving to the next position.
maxObjectHeight = Math.Max(maxObjectHeight, storage.modelSize.z);
}
public void WriteRaftGCodeIfRequired(ConfigSettings config, GCodeExport gcode)
{
LayerDataStorage storage = this;
if (config.ShouldGenerateRaft())
{
GCodePathConfig raftBaseConfig = new GCodePathConfig(config.firstLayerSpeed, config.raftBaseExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftMiddleConfig = new GCodePathConfig(config.raftPrintSpeed, config.raftInterfaceExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftSurfaceConfig = new GCodePathConfig((config.raftSurfacePrintSpeed > 0) ? config.raftSurfacePrintSpeed : config.raftPrintSpeed, config.raftSurfaceExtrusionWidth_um, "SUPPORT");
// create the raft base
{
gcode.WriteComment("LAYER:-3");
gcode.WriteComment("RAFT BASE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
if (config.raftExtruder >= 0)
{
// if we have a specified raft extruder use it
gcodeLayer.SetExtruder(config.raftExtruder);
}
else if (config.supportExtruder >= 0)
{
// else preserve the old behavior of using the support extruder if set.
gcodeLayer.SetExtruder(config.supportExtruder);
}
gcode.setZ(config.raftBaseThickness_um);
gcode.SetExtrusion(config.raftBaseThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftBaseLineSpacing_um, config.infillExtendIntoPerimeter_um, 0);
// write the skirt around the raft
gcodeLayer.QueuePolygonsByOptimizer(storage.skirt, raftBaseConfig);
// write the outline of the raft
gcodeLayer.QueuePolygonsByOptimizer(storage.raftOutline, raftBaseConfig);
// write the inside of the raft base
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftBaseConfig);
gcodeLayer.WriteQueuedGCode(config.raftBaseThickness_um);
}
if (config.raftFanSpeedPercent > 0)
{
gcode.WriteFanCommand(config.raftFanSpeedPercent);
}
// raft middle layers
{
gcode.WriteComment("LAYER:-2");
gcode.WriteComment("RAFT MIDDLE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um);
gcode.SetExtrusion(config.raftInterfaceThicknes_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftInterfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 45);
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftMiddleConfig);
gcodeLayer.WriteQueuedGCode(config.raftInterfaceThicknes_um);
}
for (int raftSurfaceIndex = 1; raftSurfaceIndex <= config.raftSurfaceLayers; raftSurfaceIndex++)
{
gcode.WriteComment("LAYER:-1");
gcode.WriteComment("RAFT SURFACE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um + config.raftSurfaceThickness_um * raftSurfaceIndex);
gcode.SetExtrusion(config.raftSurfaceThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
if (raftSurfaceIndex == config.raftSurfaceLayers)
{
// make sure the top layer of the raft is 90 degrees offset to the first layer of the part so that it has minimum contact points.
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftSurfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, config.infillStartingAngle + 90);
}
else
{
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftSurfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 90 * raftSurfaceIndex);
}
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftSurfaceConfig);
gcodeLayer.WriteQueuedGCode(config.raftInterfaceThicknes_um);
}
}
}
public void WriteRaftGCodeIfRequired(GCodeExport gcode, ConfigSettings config)
{
LayerDataStorage storage = this;
if (config.ShouldGenerateRaft())
{
GCodePathConfig raftBaseConfig = new GCodePathConfig("raftBaseConfig");
raftBaseConfig.SetData(config.FirstLayerSpeed, config.RaftBaseExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftMiddleConfig = new GCodePathConfig("raftMiddleConfig");
raftMiddleConfig.SetData(config.RaftPrintSpeed, config.RaftInterfaceExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftSurfaceConfig = new GCodePathConfig("raftMiddleConfig");
raftSurfaceConfig.SetData((config.RaftSurfacePrintSpeed > 0) ? config.RaftSurfacePrintSpeed : config.RaftPrintSpeed, config.RaftSurfaceExtrusionWidth_um, "SUPPORT");
// create the raft base
{
gcode.WriteComment("LAYER:-3");
gcode.WriteComment("RAFT BASE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.TravelSpeed, config.MinimumTravelToCauseRetraction_um, config.PerimeterStartEndOverlapRatio);
if (config.RaftExtruder >= 0)
{
// if we have a specified raft extruder use it
gcodeLayer.SetExtruder(config.RaftExtruder);
}
else if (config.SupportExtruder >= 0)
{
// else preserve the old behavior of using the support extruder if set.
gcodeLayer.SetExtruder(config.SupportExtruder);
}
gcode.setZ(config.RaftBaseThickness_um);
gcode.SetExtrusion(config.RaftBaseThickness_um, config.FilamentDiameter_um, config.ExtrusionMultiplier);
// write the skirt around the raft
gcodeLayer.QueuePolygonsByOptimizer(storage.skirt, raftBaseConfig);
List <Polygons> raftIslands = storage.raftOutline.ProcessIntoSeparatIslands();
foreach (var raftIsland in raftIslands)
{
// write the outline of the raft
gcodeLayer.QueuePolygonsByOptimizer(raftIsland, raftBaseConfig);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(raftIsland, raftLines, config.RaftBaseLineSpacing_um, config.InfillExtendIntoPerimeter_um, 0);
// write the inside of the raft base
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftBaseConfig);
if (config.RetractWhenChangingIslands)
{
gcodeLayer.ForceRetract();
}
}
gcodeLayer.WriteQueuedGCode(config.RaftBaseThickness_um);
}
if (config.RaftFanSpeedPercent > 0)
{
gcode.WriteFanCommand(config.RaftFanSpeedPercent);
}
// raft middle layers
{
gcode.WriteComment("LAYER:-2");
gcode.WriteComment("RAFT MIDDLE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.TravelSpeed, config.MinimumTravelToCauseRetraction_um, config.PerimeterStartEndOverlapRatio);
gcode.setZ(config.RaftBaseThickness_um + config.RaftInterfaceThicknes_um);
gcode.SetExtrusion(config.RaftInterfaceThicknes_um, config.FilamentDiameter_um, config.ExtrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, raftLines, config.RaftInterfaceLineSpacing_um, config.InfillExtendIntoPerimeter_um, 45);
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftMiddleConfig);
gcodeLayer.WriteQueuedGCode(config.RaftInterfaceThicknes_um);
}
for (int raftSurfaceIndex = 1; raftSurfaceIndex <= config.RaftSurfaceLayers; raftSurfaceIndex++)
{
gcode.WriteComment("LAYER:-1");
gcode.WriteComment("RAFT SURFACE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.TravelSpeed, config.MinimumTravelToCauseRetraction_um, config.PerimeterStartEndOverlapRatio);
gcode.setZ(config.RaftBaseThickness_um + config.RaftInterfaceThicknes_um + config.RaftSurfaceThickness_um * raftSurfaceIndex);
gcode.SetExtrusion(config.RaftSurfaceThickness_um, config.FilamentDiameter_um, config.ExtrusionMultiplier);
Polygons raftLines = new Polygons();
if (raftSurfaceIndex == config.RaftSurfaceLayers)
{
// make sure the top layer of the raft is 90 degrees offset to the first layer of the part so that it has minimum contact points.
Infill.GenerateLinePaths(storage.raftOutline, raftLines, config.RaftSurfaceLineSpacing_um, config.InfillExtendIntoPerimeter_um, config.InfillStartingAngle + 90);
}
else
{
Infill.GenerateLinePaths(storage.raftOutline, raftLines, config.RaftSurfaceLineSpacing_um, config.InfillExtendIntoPerimeter_um, 90 * raftSurfaceIndex);
}
gcodeLayer.QueuePolygonsByOptimizer(raftLines, raftSurfaceConfig);
gcodeLayer.WriteQueuedGCode(config.RaftInterfaceThicknes_um);
}
}
}
public static void GenerateRaftGCodeIfRequired(SliceDataStorage storage, ConfigSettings config, GCodeExport gcode)
{
if (ShouldGenerateRaft(config))
{
GCodePathConfig raftBaseConfig = new GCodePathConfig(config.firstLayerSpeed, config.extrusionWidth_um * 3, "SUPPORT");
GCodePathConfig raftMiddleConfig = new GCodePathConfig(config.raftPrintSpeed, config.raftInterfaceLinewidth_um, "SUPPORT");
GCodePathConfig raftSurfaceConfig = new GCodePathConfig((config.raftSurfacePrintSpeed > 0) ? config.raftSurfacePrintSpeed : config.raftPrintSpeed, config.raftSurfaceLinewidth_um, "SUPPORT");
// create the raft base
{
gcode.writeComment("LAYER:-3");
gcode.writeComment("RAFT BASE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
if (config.supportExtruder > 0)
{
gcodeLayer.setExtruder(config.supportExtruder);
}
gcode.setZ(config.raftBaseThickness_um);
gcode.setExtrusion(config.raftBaseThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
gcodeLayer.writePolygonsByOptimizer(storage.raftOutline, raftBaseConfig);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftBaseThickness_um, config.raftLineSpacing_um, config.infillExtendIntoPerimeter_um, 0);
gcodeLayer.writePolygonsByOptimizer(storage.skirt, raftBaseConfig);
gcodeLayer.writePolygonsByOptimizer(raftLines, raftBaseConfig);
gcodeLayer.writeGCode(false, config.raftBaseThickness_um);
}
if (config.raftFanSpeedPercent > 0)
{
gcode.writeFanCommand(config.raftFanSpeedPercent);
}
// raft middle layers
{
gcode.writeComment("LAYER:-2");
gcode.writeComment("RAFT MIDDLE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um);
gcode.setExtrusion(config.raftInterfaceThicknes_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftInterfaceLinewidth_um, config.raftInterfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 45);
gcodeLayer.writePolygonsByOptimizer(raftLines, raftMiddleConfig);
gcodeLayer.writeGCode(false, config.raftInterfaceThicknes_um);
}
for (int raftSurfaceLayer = 1; raftSurfaceLayer <= config.raftSurfaceLayers; raftSurfaceLayer++)
{
gcode.writeComment("LAYER:-1");
gcode.writeComment("RAFT SURFACE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um + config.raftSurfaceThickness_um * raftSurfaceLayer);
gcode.setExtrusion(config.raftSurfaceThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftSurfaceLinewidth_um, config.raftSurfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 90 * raftSurfaceLayer);
gcodeLayer.writePolygonsByOptimizer(raftLines, raftSurfaceConfig);
gcodeLayer.writeGCode(false, config.raftInterfaceThicknes_um);
}
}
}
public static void GenerateRaftGCodeIfRequired(SliceDataStorage storage, ConfigSettings config, GCodeExport gcode)
{
if (ShouldGenerateRaft(config))
{
GCodePathConfig raftBaseConfig = new GCodePathConfig(config.firstLayerSpeed, config.raftBaseExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftMiddleConfig = new GCodePathConfig(config.raftPrintSpeed, config.raftInterfaceExtrusionWidth_um, "SUPPORT");
GCodePathConfig raftSurfaceConfig = new GCodePathConfig((config.raftSurfacePrintSpeed > 0) ? config.raftSurfacePrintSpeed : config.raftPrintSpeed, config.raftSurfaceExtrusionWidth_um, "SUPPORT");
// create the raft base
{
gcode.writeComment("LAYER:-3");
gcode.writeComment("RAFT BASE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
if (config.raftExtruder > 0)
{
// if we have a specified raft extruder use it
gcodeLayer.setExtruder(config.raftExtruder);
}
else if (config.supportExtruder > 0)
{
// else preserve the old behavior of using the support extruder if set.
gcodeLayer.setExtruder(config.supportExtruder);
}
gcode.setZ(config.raftBaseThickness_um);
gcode.setExtrusion(config.raftBaseThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
gcodeLayer.writePolygonsByOptimizer(storage.raftOutline, raftBaseConfig);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftBaseLineSpacing_um, config.infillExtendIntoPerimeter_um, 0);
gcodeLayer.writePolygonsByOptimizer(storage.skirt, raftBaseConfig);
gcodeLayer.writePolygonsByOptimizer(raftLines, raftBaseConfig);
gcodeLayer.writeGCode(false, config.raftBaseThickness_um);
}
if (config.raftFanSpeedPercent > 0)
{
gcode.writeFanCommand(config.raftFanSpeedPercent);
}
// raft middle layers
{
gcode.writeComment("LAYER:-2");
gcode.writeComment("RAFT MIDDLE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um);
gcode.setExtrusion(config.raftInterfaceThicknes_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftInterfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 45);
gcodeLayer.writePolygonsByOptimizer(raftLines, raftMiddleConfig);
gcodeLayer.writeGCode(false, config.raftInterfaceThicknes_um);
}
for (int raftSurfaceIndex = 1; raftSurfaceIndex <= config.raftSurfaceLayers; raftSurfaceIndex++)
{
gcode.writeComment("LAYER:-1");
gcode.writeComment("RAFT SURFACE");
GCodePlanner gcodeLayer = new GCodePlanner(gcode, config.travelSpeed, config.minimumTravelToCauseRetraction_um);
gcode.setZ(config.raftBaseThickness_um + config.raftInterfaceThicknes_um + config.raftSurfaceThickness_um * raftSurfaceIndex);
gcode.setExtrusion(config.raftSurfaceThickness_um, config.filamentDiameter_um, config.extrusionMultiplier);
Polygons raftLines = new Polygons();
if (raftSurfaceIndex == config.raftSurfaceLayers)
{
// make sure the top layer of the raft is 90 degrees offset to the first layer of the part so that it has minimum contact points.
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftSurfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, config.infillStartingAngle + 90);
}
else
{
Infill.GenerateLinePaths(storage.raftOutline, ref raftLines, config.raftSurfaceLineSpacing_um, config.infillExtendIntoPerimeter_um, 90 * raftSurfaceIndex);
}
gcodeLayer.writePolygonsByOptimizer(raftLines, raftSurfaceConfig);
gcodeLayer.writeGCode(false, config.raftInterfaceThicknes_um);
}
}
}
public void WriteGCode(bool liftHeadIfNeeded, int layerThickness)
{
GCodePathConfig lastConfig = null;
int extruderIndex = gcode.GetExtruderIndex();
for (int pathIndex = 0; pathIndex < paths.Count; pathIndex++)
{
GCodePath path = paths[pathIndex];
if (extruderIndex != path.extruderIndex)
{
extruderIndex = path.extruderIndex;
gcode.SwitchExtruder(extruderIndex);
}
else if (path.Retract)
{
gcode.WriteRetraction();
}
if (path.config != travelConfig && lastConfig != path.config)
{
//gcode.WriteComment("TYPE:{0}".FormatWith(path.config.gcodeComment));
lastConfig = path.config;
////后加的//只是边框，不填充。
if ((path.config.gcodeComment == "SKIRT") || (path.config.gcodeComment == "FILL") || (path.config.gcodeComment == "TOP-FILL"))
{
return;
}
}
double speed = path.config.speed;
if (path.config.lineWidth != 0)
{
// Only apply the extrudeSpeedFactor to extrusion moves
speed = speed * extrudeSpeedFactor / 100;
}
else
{
speed = speed * travelSpeedFactor / 100;
}
if (path.points.Count == 1 &&
path.config != travelConfig &&
(gcode.GetPositionXY() - path.points[0]).ShorterThen(path.config.lineWidth * 2))
{
//Check for lots of small moves and combine them into one large line
IntPoint nextPosition = path.points[0];
int i = pathIndex + 1;
while (i < paths.Count && paths[i].points.Count == 1 && (nextPosition - paths[i].points[0]).ShorterThen(path.config.lineWidth * 2))
{
nextPosition = paths[i].points[0];
i++;
}
if (paths[i - 1].config == travelConfig)
{
i--;
}
if (i > pathIndex + 2)
{
nextPosition = gcode.GetPositionXY();
for (int x = pathIndex; x < i - 1; x += 2)
{
long oldLen = (nextPosition - paths[x].points[0]).Length();
IntPoint newPoint = (paths[x].points[0] + paths[x + 1].points[0]) / 2;
long newLen = (gcode.GetPositionXY() - newPoint).Length();
if (newLen > 0)
{
gcode.WriteMove(newPoint, speed, (int)(path.config.lineWidth * oldLen / newLen));
}
nextPosition = paths[x + 1].points[0];
}
gcode.WriteMove(paths[i - 1].points[0], speed, path.config.lineWidth);
pathIndex = i - 1;
continue;
}
}
bool spiralize = path.config.spiralize;
if (spiralize)
{
//Check if we are the last spiralize path in the list, if not, do not spiralize.
for (int m = pathIndex + 1; m < paths.Count; m++)
{
if (paths[m].config.spiralize)
{
spiralize = false;
}
}
}
if (spiralize)
{
//If we need to spiralize then raise the head slowly by 1 layer as this path progresses.
double totalLength = 0;
int z = gcode.GetPositionZ();
IntPoint currentPosition = gcode.GetPositionXY();
for (int pointIndex = 0; pointIndex < path.points.Count; pointIndex++)
{
IntPoint nextPosition = path.points[pointIndex];
totalLength += (currentPosition - nextPosition).LengthMm();
currentPosition = nextPosition;
}
double length = 0.0;
currentPosition = gcode.GetPositionXY();
for (int i = 0; i < path.points.Count; i++)
{
IntPoint nextPosition = path.points[i];
length += (currentPosition - nextPosition).LengthMm();
currentPosition = nextPosition;
gcode.setZ((int)(z + layerThickness * length / totalLength + .5));
gcode.WriteMove(path.points[i], speed, path.config.lineWidth);
}
}
else
{
#if false
// This is test code to remove double drawn small perimeter lines.
if (path.config.lineWidth > 0 &&
path.points.Count > 2 && // If the count is not greater than 2 there is no way it can ovelap itself.
gcode.GetPositionXY() == path.points[path.points.Count - 1])
{
Polygons pathsWithOverlapsRemoved = GetPathsWithOverlapsRemoved(path.points, path.config.lineWidth / 2);
if (pathsWithOverlapsRemoved.Count > 0)
{
for (int polygonIndex = 0; polygonIndex < pathsWithOverlapsRemoved.Count; polygonIndex++)
{
int startIndex = 0;
Polygon polygon = pathsWithOverlapsRemoved[polygonIndex];
if (polygonIndex > 0)
{
gcode.WriteMove(polygon[0], travelConfig.speed, 0);
startIndex = 1; // We skip the first point in the next extrusion, because we just moved to it.
}
for (int pointIndex = startIndex; pointIndex < polygon.Count; pointIndex++)
{
gcode.WriteMove(polygon[pointIndex], speed, path.config.lineWidth);
}
}
}
}
else
#endif
{
//TrimPerimeterIfNeeded(path);
for (int i = 0; i < path.points.Count; i++)
{
gcode.WriteMove(path.points[i], speed, path.config.lineWidth);
}
}
}
}
gcode.UpdateTotalPrintTime();
if (liftHeadIfNeeded && extraTime > 0.0)
{
gcode.WriteComment("Small layer, adding delay of {0}".FormatWith(extraTime));
gcode.WriteRetraction();
gcode.setZ(gcode.GetPositionZ() + 3000);
gcode.WriteMove(gcode.GetPositionXY(), travelConfig.speed, 0);
gcode.WriteMove(gcode.GetPositionXY() - new IntPoint(-20000, 0), travelConfig.speed, 0);
gcode.WriteDelay(extraTime);
}
}
