コード例 #1
0
ファイル: ULCT05.cs プロジェクト: r4forth/sdkpub
        public frm8536Count()
        {
            // This call is required by the Windows Form Designer.
            InitializeComponent();

            //  Initiate error handling
            //   activating error handling will trap errors like
            //   bad channel numbers and non-configured conditions.
            //   Parameters:
            //     MccDaq.ErrorReporting.PrintAll :all warnings and errors encountered will be printed
            //     MccDaq.ErrorHandling.StopAll   :if an error is encountered, the program will stop
            MccDaq.ErrorInfo ULStat = MccDaq.MccService.ErrHandling(MccDaq.ErrorReporting.PrintAll, MccDaq.ErrorHandling.StopAll);


            // Create a new MccBoard object for Board 0
            DaqBoard = new MccDaq.MccBoard(0);


            // Init the counter for desired operation
            //   Parameters:
            //      ChipNum     :the chip to be setup
            //      Ctr1Output  :how the counter output is used
            short ChipNum = 1;

            MccDaq.CtrlOutput Ctr1Output = MccDaq.CtrlOutput.NotLinked;
            ULStat = DaqBoard.C8536Init(ChipNum, Ctr1Output);


            // Configure the counter for desired operation
            //   Parameters:
            //      CounterNum    :which counter
            //      OutputControl :which counter output signal is used
            //      RecycleMode   :reload at 0 ?
            //      TrigType      :trigger type
            CounterNum = 1;
            MccDaq.C8536OutputControl OutputControl = MccDaq.C8536OutputControl.ToggleOnTc;
            MccDaq.RecycleMode        RecycleMode   = MccDaq.RecycleMode.Recycle;
            MccDaq.C8536TriggerType   TrigType      = MccDaq.C8536TriggerType.HWStartTrig;
            ULStat = DaqBoard.C8536Config(CounterNum, OutputControl, RecycleMode, TrigType);
        }
コード例 #2
0
        private void frm8536Count_Load(object sender, EventArgs e)
        {
            InitUL();
            NumCtrs = CtrProps.FindCountersOfType(DaqBoard, CounterType, out CounterNum);
            if (NumCtrs == 0)
            {
                lblNoteFreqIn.Text = "Board " + DaqBoard.BoardNum.ToString() +
                                     " has no 8536 counters.";
                cmdStart.Enabled = false;
            }
            else
            {
                // Init the counter for desired operation
                //   Parameters:
                //      ChipNum     :the chip to be setup
                //      Ctr1Output  :how the counter output is used
                short             ChipNum    = 1;
                MccDaq.CtrlOutput Ctr1Output = MccDaq.CtrlOutput.NotLinked;
                MccDaq.ErrorInfo  ULStat     = DaqBoard.C8536Init(ChipNum, Ctr1Output);


                // Configure the counter for desired operation
                //   Parameters:
                //      CounterNum    :which counter
                //      OutputControl :which counter output signal is used
                //      RecycleMode   :reload at 0 ?
                //      TrigType      :trigger type
                CounterNum = 1;
                MccDaq.C8536OutputControl OutputControl = MccDaq.C8536OutputControl.ToggleOnTc;
                MccDaq.RecycleMode        RecycleMode   = MccDaq.RecycleMode.Recycle;
                MccDaq.C8536TriggerType   TrigType      = MccDaq.C8536TriggerType.HWStartTrig;
                ULStat = DaqBoard.C8536Config(CounterNum, OutputControl, RecycleMode, TrigType);
                this.lblNoteFreqIn.Text =
                    "NOTE: There must be a TTL frequency at counter 1 input on board "
                    + DaqBoard.BoardNum.ToString() + ".";
            }
        }
コード例 #3
0
ファイル: ULCT05.cs プロジェクト: otoauler/sdkpub
        public frm8536Count()
        {
            // This call is required by the Windows Form Designer.
            InitializeComponent();

            //  Initiate error handling
            //   activating error handling will trap errors like
            //   bad channel numbers and non-configured conditions.
            //   Parameters:
            //     MccDaq.ErrorReporting.PrintAll :all warnings and errors encountered will be printed
            //     MccDaq.ErrorHandling.StopAll   :if an error is encountered, the program will stop
            MccDaq.ErrorInfo ULStat = MccDaq.MccService.ErrHandling(MccDaq.ErrorReporting.PrintAll, MccDaq.ErrorHandling.StopAll);

            // Create a new MccBoard object for Board 0
            DaqBoard = new MccDaq.MccBoard(0);

            // Init the counter for desired operation
            //   Parameters:
            //      ChipNum     :the chip to be setup
            //      Ctr1Output  :how the counter output is used
            short ChipNum = 1;
            MccDaq.CtrlOutput Ctr1Output = MccDaq.CtrlOutput.NotLinked;
            ULStat = DaqBoard.C8536Init(ChipNum, Ctr1Output);

            // Configure the counter for desired operation
            //   Parameters:
            //      CounterNum    :which counter
            //      OutputControl :which counter output signal is used
            //      RecycleMode   :reload at 0 ?
            //      TrigType      :trigger type
            CounterNum = 1;
            MccDaq.C8536OutputControl OutputControl = MccDaq.C8536OutputControl.ToggleOnTc;
            MccDaq.RecycleMode RecycleMode = MccDaq.RecycleMode.Recycle;
            MccDaq.C8536TriggerType TrigType = MccDaq.C8536TriggerType.HWStartTrig;
            ULStat = DaqBoard.C8536Config(CounterNum, OutputControl, RecycleMode, TrigType);
        }