// Post
public void TranslateT2C(TransCAD.IStdSketchGeometry tGeom)
{
if (tGeom.Type == TransCAD.StdSketchGeometryType.Circle) // Circle인 경우
{
TransCAD.IStdSketchCircle tCircle = (TransCAD.IStdSketchCircle)tGeom;
TransCAD.StdSketchControlPoint tCenterPoint = (TransCAD.StdSketchControlPoint)tCircle.CenterPoint;
double cX = tCircle.CenterPoint.X;
double cY = tCircle.CenterPoint.Y;
MECMOD.Point2D cCenterPoint = SketchManager.cFactory.CreatePoint(cX, cY);
cCenterPoint.ReportName = ++SketchManager.cReportName;
double tRadius = tCircle.Radius;
MECMOD.Circle2D cCircle = SketchManager.cFactory.CreateClosedCircle(cX, cY, tRadius);
cCircle.CenterPoint = cCenterPoint;
cCircle.ReportName = ++SketchManager.cReportName;
}
else if (tGeom.Type == TransCAD.StdSketchGeometryType.CircularArc) // Arc인 경우
{
TransCAD.IStdSketchCircularArc tArc = (TransCAD.IStdSketchCircularArc)tGeom;
TransCAD.StdSketchControlPoint tCenterPoint = (TransCAD.StdSketchControlPoint)tArc.CenterPoint;
TransCAD.StdSketchControlPoint tStartPoint = (TransCAD.StdSketchControlPoint)tArc.StartPoint;
TransCAD.StdSketchControlPoint tEndPoint = (TransCAD.StdSketchControlPoint)tArc.EndPoint;
double cX = tArc.CenterPoint.X;
double cY = tArc.CenterPoint.Y;
MECMOD.Point2D cCenterPoint = SketchManager.cFactory.CreatePoint(cX, cY);
cCenterPoint.ReportName = ++SketchManager.cReportName;
double sX = tStartPoint.X;
double sY = tStartPoint.Y;
MECMOD.Point2D cStartPoint = SketchManager.cFactory.CreatePoint(sX, sY);
cStartPoint.ReportName = ++SketchManager.cReportName;
double eX = tEndPoint.X;
double eY = tEndPoint.Y;
MECMOD.Point2D cEndPoint = SketchManager.cFactory.CreatePoint(eX, eY);
cEndPoint.ReportName = ++SketchManager.cReportName;
double sA = tArc.StartAngle;
double eA = tArc.EndAngle;
double tRadius = tArc.Radius;
MECMOD.Circle2D cCircle = SketchManager.cFactory.CreateCircle(cX, cY, tRadius, sA, eA);
cCircle.CenterPoint = cCenterPoint;
cCircle.StartPoint = cStartPoint;
cCircle.EndPoint = cEndPoint;
cCircle.ReportName = ++SketchManager.cReportName;
}
}
// Post
public void TranslateT2C(TransCAD.IStdSketchGeometry tGeom)
{
if (tGeom.Type == TransCAD.StdSketchGeometryType.Line) // 일반 Line인 경우
{
TransCAD.IStdSketchLine tLine = (TransCAD.IStdSketchLine)tGeom;
TransCAD.StdSketchControlPoint tStartPoint = (TransCAD.StdSketchControlPoint)tLine.StartPoint;
TransCAD.StdSketchControlPoint tEndPoint = (TransCAD.StdSketchControlPoint)tLine.EndPoint;
double sX = tStartPoint.X;
double sY = tStartPoint.Y;
MECMOD.Point2D cStartPoint = SketchManager.cFactory.CreatePoint(sX, sY);
cStartPoint.ReportName = ++SketchManager.cReportName;
double eX = tEndPoint.X;
double eY = tEndPoint.Y;
MECMOD.Point2D cEndPoint = SketchManager.cFactory.CreatePoint(eX, eY);
cEndPoint.ReportName = ++SketchManager.cReportName;
MECMOD.Line2D cLine = SketchManager.cFactory.CreateLine(sX, sY, eX, eY);
cLine.StartPoint = cStartPoint;
cLine.EndPoint = cEndPoint;
cLine.ReportName = ++SketchManager.cReportName;
}
else if (tGeom.Type == TransCAD.StdSketchGeometryType.Centerline) // Centerline인 경우
{
TransCAD.IStdSketchCenterline tLine = (TransCAD.IStdSketchCenterline)tGeom;
TransCAD.StdSketchControlPoint tStartPoint = (TransCAD.StdSketchControlPoint)tLine.StartPoint;
TransCAD.StdSketchControlPoint tEndPoint = (TransCAD.StdSketchControlPoint)tLine.EndPoint;
double sX = tStartPoint.X;
double sY = tStartPoint.Y;
MECMOD.Point2D cStartPoint = SketchManager.cFactory.CreatePoint(sX, sY);
cStartPoint.ReportName = ++SketchManager.cReportName;
double eX = tEndPoint.X;
double eY = tEndPoint.Y;
MECMOD.Point2D cEndPoint = SketchManager.cFactory.CreatePoint(eX, eY);
cEndPoint.ReportName = ++SketchManager.cReportName;
MECMOD.Line2D cLine = SketchManager.cFactory.CreateLine(sX, sY, eX, eY);
cLine.StartPoint = cStartPoint;
cLine.EndPoint = cEndPoint;
cLine.ReportName = ++SketchManager.cReportName;
SketchManager.cCenterLine = cLine;
}
}
