void ModifyRouteSeqV2(bool bface6, BorderSequenceEntity borderSeq, ArrayList Seqlist, ref int routeswqindex, ref ArrayList outstrlist)
{
if (Seqlist.Count > 0)
{
if (bface6)
{
for (int i = 0; i < Seqlist.Count; i++)
{
double d1 = Convert.ToDouble(borderSeq.PanelThickness);
double c1 = Convert.ToDouble(borderSeq.PanelLength);
RouteSetMillSequenceEntity route = Seqlist[i] as RouteSetMillSequenceEntity;
double di = Convert.ToDouble(route.RouteSetMillZ);
double pi = Convert.ToDouble(route.RouteX);
if (di < d1 && (pi <= 0 || pi >= c1) && route.RouteToolName != "D3") //开槽发现有D3刀开的槽是需要过滤的，不需要开槽功能 宋新刚20170823
{
VdrillSequenceEntity vdrill = new VdrillSequenceEntity();
double drillx = Convert.ToDouble(route.RouteX);
if (drillx <= 0)
{
vdrill.VDrillX = "0.1";
}
else if (drillx >= c1)
{
vdrill.VDrillX = (c1 - 0.1).ToString();
}
if (Convert.ToDouble(route.RouteToolComp) == 0)
{
vdrill.VDrillY = route.RouteSetMillY;
}
else if (Convert.ToDouble(route.RouteToolComp) == 1)
{
vdrill.VDrillY = (Convert.ToDouble(route.RouteSetMillY) + 0.5 * Convert.ToDouble(route.RouteDiameter)).ToString();
}
else if (Convert.ToDouble(route.RouteToolComp) == 2)
{
vdrill.VDrillY = (Convert.ToDouble(route.RouteSetMillY) - 0.5 * Convert.ToDouble(route.RouteDiameter)).ToString();
}
vdrill.VdrillSequence = "VdrillSequence";
vdrill.VDrillZ = route.RouteSetMillZ;
vdrill.VDrillXOffset = "0";
vdrill.VDrillYOffset = "0";
vdrill.VDrillDiameter = "12.2";
vdrill.VDrillToolName = "12.2mm";
vdrill.VDrillFeedSpeed = "3000";
vdrill.VDrillEntrySpeed = "8000";
if (borderSeq.Description.Trim() == "翻门板")
{
continue;
}
outstrlist.Add(vdrill.OutPutCsvString());
}
}
}
for (int i = 0; i < Seqlist.Count; i++)
{
RouteSetMillSequenceEntity route = Seqlist[i] as RouteSetMillSequenceEntity;
route.RouteVectorCount = (Seqlist.Count - 1).ToString();
// 解决翻板门板矩形孔出现波浪型线条问题 宋新刚 20170114
if (route.RouteVectorCount == "19" && borderSeq.Description.IndexOf("门板") > -1)
{
continue;
}
if (Convert.ToDouble(route.RouteVectorCount) > 20) //发现AD有切大的矩形 在这里如果拐点大于20就删 宋新刚 20170309
{
continue;
}
if (route.RouteVectorCount == "3" && (borderSeq.Description.Equals("MB-左开门板(横纹)") || borderSeq.Description.Equals("MB-右开门板(横纹)")))
{
continue; //发现AD过来的时候，对于门板横纹 做拉手孔的时候也出现波浪线的问题。做了修复 宋新刚20170322
}
if (route.RouteVectorCount == "3" && (borderSeq.Description.IndexOf("MB-榻榻米门板") > -1 && borderSeq.Description.IndexOf("(横纹)") > -1))
{
continue; //发现AD过来的时候，对新增加的名字做了修复 宋新刚20170829
}
if (route.RouteVectorCount == "3" && (borderSeq.Description.IndexOf("门板") > -1))
{
continue; //发现AD过来的时候，对新增加的名字做了修复 宋新刚20171024
}
//if (route.RouteVectorCount == "1" && borderSeq.Description.Trim() == "翻门板")
// continue; //发现多出来的部分是切除多余的板数据的 所以取消 宋新刚 20170118
// 解决翻板门板矩形孔出现波浪型线条问题 宋新刚 20170114
if (!string.IsNullOrEmpty(route.RouteBulge) && route.RouteBulge != "0.0000" && route.RouteBulge != "0")
{
if (i > 0)
{
RouteSetMillSequenceEntity route1 = Seqlist[i - 1] as RouteSetMillSequenceEntity;
double x1 = 0, x2 = 0, y1 = 0, y2 = 0, l = 0, u = 0, radius = 0, ang = 0, cenx = 0, ceny = 0;
double.TryParse(route1.RouteX, out x1);
double.TryParse(route1.RouteY, out y1);
double.TryParse(route.RouteX, out x2);
double.TryParse(route.RouteY, out y2);
double.TryParse(route.RouteBulge, out u);
l = Math.Sqrt(Math.Pow(x1 - x2, 2) + Math.Pow(y1 - y2, 2));
radius = 0.25 * l * (u + 1 / u);
route.RouteRadius = string.Format("{0:f4}", radius);
if (x1 == x2)
{
ang = Math.PI / 2;
if (u > 0)
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2);
ceny = (y1 + y2) / 2;
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2);
ceny = (y1 + y2) / 2;
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2);
ceny = (y1 + y2) / 2;
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2);
ceny = (y1 + y2) / 2;
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
}
else
{
ang = Math.Atan((y1 - y2) / (x1 - x2));
if (u > 0)
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 - (radius - l * u / 2) * Math.Cos(ang);
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 + (radius - l * u / 2) * Math.Cos(ang);
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 + (radius - l * u / 2) * Math.Cos(ang);
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 - (radius - l * u / 2) * Math.Cos(ang);
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
}
}
}
outstrlist.Add(route.OutPutCsvString());
}
routeswqindex = 0;
Seqlist.Clear();
}
}
public bool ModifyDataFromCsv(string csvFilename, bool bface6, ref double sheetWidth, ref double sheetLength)
{
int thickness = 0; //发现水平孔位的Z值有超过板厚的数据。将这数据过滤掉 宋新刚 20171101
try
{
StreamReader sr = new StreamReader(csvFilename, Encoding.Default);
string strLine = sr.ReadLine();
//strLine = sr.ReadToEnd();
int RouteSetIndex = 0;
int routeswqindex = 0;
ArrayList Seqlist = new ArrayList();
Seqlist.Clear();
bool hasend = false;
ArrayList outstrlist = new ArrayList();
BorderSequenceEntity borderSeq = new BorderSequenceEntity(strLine);
sheetWidth = 0;
double.TryParse(borderSeq.PanelWidth, out sheetWidth);
sheetLength = 0;
double.TryParse(borderSeq.PanelLength, out sheetLength);
while (strLine != null)
{
strLine = strLine.Replace("D8.5", "129").Replace("D10", "130");
if (strLine.IndexOf("EndSequence,") == 0)
{
hasend = true;
outstrlist.Add(strLine);
}
////处理每行的字符串
else if (strLine.IndexOf("BorderSequence,") == 0)
{
borderSeq.NestRoutesCount = "0";
borderSeq.Edgeband1 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband2 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband3 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband4 = borderSeq.Edgeband1.Replace("MM", "mm");
if (borderSeq.CurrentZoneName == "AD")
{
borderSeq.CurrentZoneName = "M";
borderSeq.RunField = "3";
}
if (borderSeq.CurrentZoneName == "DA")
{
borderSeq.CurrentZoneName = "N";
borderSeq.RunField = "4";
}
thickness = Convert.ToInt32(borderSeq.PanelThickness); //发现水平孔位的Z值有超过板厚的数据。将这数据过滤掉 宋新刚 20171101
if (bface6)
{
borderSeq.Face6FileName = Path.GetFileNameWithoutExtension(csvFilename);
}
else
{
borderSeq.FileName = Path.GetFileNameWithoutExtension(csvFilename);
}
string output = borderSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("HDrillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
HDrillSequenceEntity hdrillSeq = new HDrillSequenceEntity(strLine);
hdrillSeq.HDrillFeedSpeed = "3000";
hdrillSeq.HDrillEntrySpeed = "2700";
/*** 用于解决水平孔加工面产生小数点的问题 宋新刚20161115 * **/
if (hdrillSeq.CurrentFace == "1.0000")
{
hdrillSeq.CurrentFace = "1";
}
else if (hdrillSeq.CurrentFace == "2.0000")
{
hdrillSeq.CurrentFace = "2";
}
else if (hdrillSeq.CurrentFace == "3.0000")
{
hdrillSeq.CurrentFace = "3";
}
else if (hdrillSeq.CurrentFace == "4.0000")
{
hdrillSeq.CurrentFace = "4";
}
// 以下是解决工程部 双向拉杆有水平孔为0的情况
if (hdrillSeq.HDrillDiameter == "0" || hdrillSeq.HDrillDiameter == "0.0000")
{
strLine = sr.ReadLine();
continue;
}
// 以下是发现水平孔位的Z值有超过板厚的数据。将这数据过滤掉 宋新刚 20171101
if (Convert.ToDouble(hdrillSeq.HDrillY) > thickness) //发现其高度值有小数。所以这里必须得是Double类型 宋新刚20171106
{
strLine = sr.ReadLine();
continue;
}
// 以下是解决工程部 水平孔的坐标出现负数的情况
if (hdrillSeq.HDrillZ.IndexOf("-") == 0 || hdrillSeq.HDrillX.IndexOf("-") == 0 || hdrillSeq.HDrillY.IndexOf("-") == 0)
{
// MessageBox.Show(" 以下是解决工程部 水平孔的坐标出现负数的情况");
strLine = sr.ReadLine();
continue;
}
// 宋新刚 20161114
// 以下是解决舟山翻床厚背板镜像加工 在面1和面2上多出现10的水平孔 通过式PTP无法加工
if (hdrillSeq.HDrillDiameter == "10.0000" || hdrillSeq.HDrillDiameter == "10")
{
strLine = sr.ReadLine();
continue;
} //证明水平孔不可能有10的情况。遇到有10的水平孔全部删除
string output = hdrillSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("VdrillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
VdrillSequenceEntity vdrillSeq = new VdrillSequenceEntity(strLine);
vdrillSeq.VDrillFeedSpeed = "3000";
vdrillSeq.VDrillEntrySpeed = "8000";
// 以下是解决工程部 垂直孔的坐标出现负数的情况
if (vdrillSeq.VDrillX.IndexOf("-") == 0 || vdrillSeq.VDrillY.IndexOf("-") == 0 || vdrillSeq.VDrillZ.IndexOf("-") == 0)
{
strLine = sr.ReadLine();
continue;
}
//以下是解决工程部模型 孔位超出板材范围的情况
if (Convert.ToDouble(vdrillSeq.VDrillY) - Convert.ToDouble(borderSeq.PanelWidth) > 0)
{
strLine = sr.ReadLine();
continue;
}
if (Convert.ToDouble(vdrillSeq.VDrillX) - Convert.ToDouble(borderSeq.PanelLength) > 0)
{
strLine = sr.ReadLine();
continue;
}
// 宋新刚 20161114
string output = vdrillSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("RouteSetMillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
RouteSetIndex++;
RouteSetMillSequenceEntity routeSeq = new RouteSetMillSequenceEntity(strLine);
routeSeq.RouteSetMillCounter = RouteSetIndex.ToString();
routeSeq.RouteVectorCounter = "";
routeSeq.RouteVectorCount = "";
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteToolComp) == 1)
{
routeSeq.RouteToolComp = "2";
}
else if (Convert.ToDouble(routeSeq.RouteToolComp) == 2)
{
routeSeq.RouteToolComp = "1";
}
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteSetMillZ) == 9.25 && Convert.ToDouble(routeSeq.RouteDiameter) == 8.5 && Convert.ToDouble(routeSeq.RouteZ) == 9.25) //发现AD过来的背板槽 有固定的9.25深 修复为5mm深 宋新刚 2018年1月26日
{
routeSeq.RouteSetMillZ = "5";
routeSeq.RouteZ = "5";
}
Seqlist.Add(routeSeq);
}
else if (strLine.IndexOf("RouteSequence,") == 0)
{
routeswqindex++;
RouteSetMillSequenceEntity routeSeq = new RouteSetMillSequenceEntity(strLine);
routeSeq.RouteSetMillCounter = RouteSetIndex.ToString();
routeSeq.RouteVectorCounter = routeswqindex.ToString();
routeSeq.RouteVectorCount = "";
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteToolComp) == 1)
{
routeSeq.RouteToolComp = "2";
}
else if (Convert.ToDouble(routeSeq.RouteToolComp) == 2)
{
routeSeq.RouteToolComp = "1";
}
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteSetMillZ) == 9.25 && Convert.ToDouble(routeSeq.RouteDiameter) == 8.5 && Convert.ToDouble(routeSeq.RouteZ) == 9.25) //发现AD过来的背板槽 有固定的9.25深 修复为5mm深 宋新刚 2018年1月26日
{
routeSeq.RouteSetMillZ = "5";
routeSeq.RouteZ = "5";
}
Seqlist.Add(routeSeq);
}
strLine = sr.ReadLine();
}
sr.Close();
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
//string TempFile = Path.ChangeExtension(csvFilename, "temp");
StreamWriter sw = new StreamWriter(csvFilename, false, Encoding.Default);
foreach (string str in outstrlist)
{
if (string.IsNullOrEmpty(str))
{
continue;
}
sw.WriteLine(str);
}
if (!hasend)
{
sw.WriteLine("EndSequence,,,,");
}
sw.Flush();
sw.Close();
return(true);
}
catch (SystemException ex)
{
MessageBox.Show("代码转换出现异常 " + ex.Message + "\n" + csvFilename);
return(false);
}
}
void ModifyRouteSeqV(ArrayList Seqlist, ref int routeswqindex, ref ArrayList outstrlist)
{
if (Seqlist.Count > 0)
{
for (int i = 0; i < Seqlist.Count; i++)
{
RouteSetMillSequenceEntity route = Seqlist[i] as RouteSetMillSequenceEntity;
route.RouteVectorCount = (Seqlist.Count - 1).ToString();
if (!string.IsNullOrEmpty(route.RouteBulge) && route.RouteBulge != "0.0000" && route.RouteBulge != "0")
{
if (i > 0)
{
RouteSetMillSequenceEntity route1 = Seqlist[i - 1] as RouteSetMillSequenceEntity;
double x1 = 0, x2 = 0, y1 = 0, y2 = 0, l = 0, u = 0, radius = 0, ang = 0, cenx = 0, ceny = 0;
double.TryParse(route1.RouteX, out x1);
double.TryParse(route1.RouteY, out y1);
double.TryParse(route.RouteX, out x2);
double.TryParse(route.RouteY, out y2);
double.TryParse(route.RouteBulge, out u);
l = Math.Sqrt(Math.Pow(x1 - x2, 2) + Math.Pow(y1 - y2, 2));
radius = 0.25 * l * (u + 1 / u);
route.RouteRadius = string.Format("{0:f4}", radius);
if (x1 == x2)
{
ang = Math.PI / 2;
if (u > 0)
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2);
ceny = (y1 + y2) / 2;
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2);
ceny = (y1 + y2) / 2;
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2);
ceny = (y1 + y2) / 2;
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2);
ceny = (y1 + y2) / 2;
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
}
else
{
ang = Math.Atan((y1 - y2) / (x1 - x2));
if (u > 0)
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 - (radius - l * u / 2) * Math.Cos(ang);
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 + (radius - l * u / 2) * Math.Cos(ang);
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
else
{
cenx = (x1 + x2) / 2 - (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 + (radius - l * u / 2) * Math.Cos(ang);
if ((x2 - x1) * (ceny - y2) - (y2 - y1) * (cenx - x2) < 0)
{
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
else
{
cenx = (x1 + x2) / 2 + (radius - l * u / 2) * Math.Sin(ang);
ceny = (y1 + y2) / 2 - (radius - l * u / 2) * Math.Cos(ang);
route.RouteCenterX = string.Format("{0:f4}", cenx);;
route.RouteCenterY = string.Format("{0:f4}", ceny);;
}
}
}
}
}
outstrlist.Add(route.OutPutCsvString());
}
routeswqindex = 0;
Seqlist.Clear();
}
}
public bool ReadDataFromCsv(string csvFilename, bool bface6)
{
try
{
StreamReader sr = new StreamReader(csvFilename, Encoding.Default);
string strLine = sr.ReadLine();
//strLine = sr.ReadToEnd();
int RouteSetIndex = 0;
int routeswqindex = 0;
ArrayList Seqlist = new ArrayList();
Seqlist.Clear();
ArrayList outstrlist = new ArrayList();
BorderSequenceEntity borderSeq = new BorderSequenceEntity(strLine);
while (strLine != null)
{
strLine = strLine.Replace("D8.5", "129").Replace("D10", "130");
////处理每行的字符串
if (strLine.IndexOf("BorderSequence,") == 0)
{
//BorderSequenceEntity borderSeq = new BorderSequenceEntity(strLine);
borderSeq.NestRoutesCount = "0";
borderSeq.FileName = Path.GetFileNameWithoutExtension(csvFilename);
borderSeq.Edgeband1 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband2 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband3 = borderSeq.Edgeband1.Replace("MM", "mm");
borderSeq.Edgeband4 = borderSeq.Edgeband1.Replace("MM", "mm");
string output = borderSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("HDrillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
HDrillSequenceEntity hdrillSeq = new HDrillSequenceEntity(strLine);
hdrillSeq.HDrillFeedSpeed = "3000";
hdrillSeq.HDrillEntrySpeed = "2700";
string output = hdrillSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("VdrillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
VdrillSequenceEntity vdrillSeq = new VdrillSequenceEntity(strLine);
vdrillSeq.VDrillFeedSpeed = "3000";
vdrillSeq.VDrillEntrySpeed = "8000";
string output = vdrillSeq.OutPutCsvString();
outstrlist.Add(output);
}
else if (strLine.IndexOf("RouteSetMillSequence,") == 0)
{
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
RouteSetIndex++;
RouteSetMillSequenceEntity routeSeq = new RouteSetMillSequenceEntity(strLine);
routeSeq.RouteSetMillCounter = RouteSetIndex.ToString();
routeSeq.RouteVectorCounter = "";
routeSeq.RouteVectorCount = "";
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteToolComp) == 1)
{
routeSeq.RouteToolComp = "2";
}
else if (Convert.ToDouble(routeSeq.RouteToolComp) == 2)
{
routeSeq.RouteToolComp = "1";
}
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
Seqlist.Add(routeSeq);
}
else if (strLine.IndexOf("RouteSequence,") == 0)
{
routeswqindex++;
RouteSetMillSequenceEntity routeSeq = new RouteSetMillSequenceEntity(strLine);
routeSeq.RouteSetMillCounter = RouteSetIndex.ToString();
routeSeq.RouteVectorCounter = routeswqindex.ToString();
routeSeq.RouteVectorCount = "";
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
if (Convert.ToDouble(routeSeq.RouteToolComp) == 1)
{
routeSeq.RouteToolComp = "2";
}
else if (Convert.ToDouble(routeSeq.RouteToolComp) == 2)
{
routeSeq.RouteToolComp = "1";
}
// 发现AD出来的只要有偏置的地方都需要对调一下 宋新刚 20170118
Seqlist.Add(routeSeq);
}
strLine = sr.ReadLine();
}
sr.Close();
ModifyRouteSeqV2(bface6, borderSeq, Seqlist, ref routeswqindex, ref outstrlist);
string TempFile = Path.ChangeExtension(csvFilename, "temp");
StreamWriter sw = new StreamWriter(TempFile, false, Encoding.Default);
foreach (string str in outstrlist)
{
if (string.IsNullOrEmpty(str))
{
continue;
}
sw.WriteLine(str);
}
sw.Flush();
sw.Close();
return(true);
}
catch (SystemException ex)
{
return(false);
}
}