public byte StoreSegment(segment_t segment)
{
lock (this)
{
// Segment complete! Increment segment buffer indices.
segment_buffer[segment_buffer_head] = segment;
segment_buffer_head = segment_next_head;
if (++segment_next_head == GrblFirmware.SEGMENT_BUFFER_SIZE) { segment_next_head = 0; }
recalcSegmentBufferCount();
}
RaiseStepperSegmentBufferChanged();
return (byte)AskHasMoreSegmentBuffer();
}
//public void StoreSegment(segment_t segment)
public byte StoreSegment(segment_t segment)
{
byte n_stepHI = mGetSubByteByIndex(Convert.ToInt32(segment.n_step), 1);
byte n_stepLO = mGetSubByteByIndex(Convert.ToInt32(segment.n_step), 0);
Debug.WriteLine("StoreSegment, cycles_per_tick={0}, stepIdx={1}, steps={2}", segment.cycles_per_tick, segment.st_block_index, segment.n_step);
byte cycles_per_tickHI = mGetSubByteByIndex(Convert.ToInt32(segment.cycles_per_tick), 1);
byte cycles_per_tickLO = mGetSubByteByIndex(Convert.ToInt32(segment.cycles_per_tick), 0);
var data = new List<byte>() { n_stepLO, n_stepHI,
segment.st_block_index,
cycles_per_tickLO, cycles_per_tickHI,
segment.amass_level,
segment.prescaler};
Debug.WriteLine("StoreSegment");
List<byte> readData;
//mComMan.Send(ECommands.STORESEGMENT_COMMAND, data);
mComMan.SendAndRead(ECommands.STORESEGMENT_COMMAND, data, ECommands.OKSTORESEGMENT_COMMAND, out readData);
return readData[0];
}
/* Prepares step segment buffer. Continuously called from main program.
The segment buffer is an intermediary buffer interface between the execution of steps
by the stepper algorithm and the velocity profiles generated by the planner. The stepper
algorithm only executes steps within the segment buffer and is filled by the main program
when steps are "checked-out" from the first block in the planner buffer. This keeps the
step execution and planning optimization processes atomic and protected from each other.
The number of steps "checked-out" from the planner buffer and the number of segments in
the segment buffer is sized and computed such that no operation in the main program takes
longer than the time it takes the stepper algorithm to empty it before refilling it.
Currently, the segment buffer conservatively holds roughly up to 40-50 msec of steps.
NOTE: Computation units are in steps, millimeters, and minutes.
*/
public bool st_prep_buffer()
{
int bufferSpace = mLaserCatHardware.AskHasMoreSegmentBuffer();
//Logging.Log.LogInfo("-------- Sending " + bufferSpace + " segments");
int i = 1;
while (bufferSpace > 0)
{
i++;
if (i == 50)
return true;
bufferSpace--;
//while (mLaserCatHardware.AskHasMoreSegmentBuffer() > 0) {
// Determine if we need to load a new planner block or if the block has been replanned.
if (pl_blockIdx == -1)
{
pl_blockIdx = mPlanner.plan_get_current_block(); // Query planner for a queued block
if (pl_blockIdx == -1) { return false; } // No planner blocks. Exit.
// Check if the segment buffer completed the last planner block. If so, load the Bresenham
// data for the block. If not, we are still mid-block and the velocity profile was updated.
if (prep.flag_partial_block != 0)
{
prep.flag_partial_block = 0; // Reset flag
}
else
{
// Increment stepper common data index to store new planner block data.
if (++prep.st_block_index == (SEGMENT_BUFFER_SIZE - 1)) { prep.st_block_index = 0; }
// Prepare and copy Bresenham algorithm segment data from the new planner block, so that
// when the segment buffer completes the planner block, it may be discarded when the
// segment buffer finishes the prepped block, but the stepper ISR is still executing it.
st_block_t st_block_buffer = new st_block_t(true);
st_block_buffer.direction_bits = mPlanner.block_buffer[pl_blockIdx].direction_bits;
if (!ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING)
{
st_block_buffer.steps[NutsAndBolts.X_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.X_AXIS];
st_block_buffer.steps[NutsAndBolts.Y_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.Y_AXIS];
st_block_buffer.steps[NutsAndBolts.Z_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.Z_AXIS];
st_block_buffer.step_event_count = mPlanner.block_buffer[pl_blockIdx].step_event_count;
}
else
{
// With AMASS enabled, simply bit-shift multiply all Bresenham data by the max AMASS
// level, such that we never divide beyond the original data anywhere in the algorithm.
// If the original data is divided, we can lose a step from integer roundoff.
st_block_buffer.steps[NutsAndBolts.X_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.X_AXIS] << MAX_AMASS_LEVEL;
st_block_buffer.steps[NutsAndBolts.Y_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.Y_AXIS] << MAX_AMASS_LEVEL;
st_block_buffer.steps[NutsAndBolts.Z_AXIS] = mPlanner.block_buffer[pl_blockIdx].steps[NutsAndBolts.Z_AXIS] << MAX_AMASS_LEVEL;
st_block_buffer.step_event_count = mPlanner.block_buffer[pl_blockIdx].step_event_count << MAX_AMASS_LEVEL;
}
mLaserCatHardware.StorePlannerBlock(prep.st_block_index, st_block_buffer);
// Initialize segment buffer data for generating the segments.
prep.steps_remaining = mPlanner.block_buffer[pl_blockIdx].step_event_count;
prep.step_per_mm = prep.steps_remaining / mPlanner.block_buffer[pl_blockIdx].millimeters;
prep.req_mm_increment = REQ_MM_INCREMENT_SCALAR / prep.step_per_mm;
prep.dt_remainder = 0.0f; // Reset for new planner block
if (sys.state == STATE_HOLD)
{
// Override planner block entry speed and enforce deceleration during feed hold.
prep.current_speed = prep.exit_speed;
mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr = prep.exit_speed * prep.exit_speed;
}
else { prep.current_speed = (float)System.Math.Sqrt(mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr); }
}
/* ---------------------------------------------------------------------------------
Compute the velocity profile of a new planner block based on its entry and exit
speeds, or recompute the profile of a partially-completed planner block if the
planner has updated it. For a commanded forced-deceleration, such as from a feed
hold, override the planner velocities and decelerate to the target exit speed.
*/
prep.mm_complete = 0.0f; // Default velocity profile complete at 0.0mm from end of block.
float inv_2_accel = 0.5f / mPlanner.block_buffer[pl_blockIdx].acceleration;
if (sys.state == STATE_HOLD)
{ // [Forced Deceleration to Zero Velocity]
// Compute velocity profile parameters for a feed hold in-progress. This profile overrides
// the planner block profile, enforcing a deceleration to zero speed.
prep.ramp_type = RAMP_DECEL;
// Compute decelerate distance relative to end of block.
float decel_dist = mPlanner.block_buffer[pl_blockIdx].millimeters - inv_2_accel * mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr;
if (decel_dist < 0.0)
{
// Deceleration through entire planner block. End of feed hold is not in this block.
prep.exit_speed = (float)System.Math.Sqrt(mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr - 2 * mPlanner.block_buffer[pl_blockIdx].acceleration * mPlanner.block_buffer[pl_blockIdx].millimeters);
}
else
{
prep.mm_complete = decel_dist; // End of feed hold.
prep.exit_speed = 0.0f;
}
}
else
{ // [Normal Operation]
// Compute or recompute velocity profile parameters of the prepped planner block.
prep.ramp_type = RAMP_ACCEL; // Initialize as acceleration ramp.
prep.accelerate_until = mPlanner.block_buffer[pl_blockIdx].millimeters;
prep.exit_speed = mPlanner.plan_get_exec_block_exit_speed();
float exit_speed_sqr = prep.exit_speed * prep.exit_speed;
float intersect_distance =
0.5f * (mPlanner.block_buffer[pl_blockIdx].millimeters + inv_2_accel * (mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr - exit_speed_sqr));
if (intersect_distance > 0.0f)
{
if (intersect_distance < mPlanner.block_buffer[pl_blockIdx].millimeters)
{ // Either trapezoid or triangle types
// NOTE: For acceleration-cruise and cruise-only types, following calculation will be 0.0.
prep.decelerate_after = inv_2_accel * (mPlanner.block_buffer[pl_blockIdx].nominal_speed_sqr - exit_speed_sqr);
if (prep.decelerate_after < intersect_distance)
{ // Trapezoid type
prep.maximum_speed = (float)System.Math.Sqrt(mPlanner.block_buffer[pl_blockIdx].nominal_speed_sqr);
if (mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr == mPlanner.block_buffer[pl_blockIdx].nominal_speed_sqr)
{
// Cruise-deceleration or cruise-only type.
prep.ramp_type = RAMP_CRUISE;
}
else
{
// Full-trapezoid or acceleration-cruise types
prep.accelerate_until -= inv_2_accel * (mPlanner.block_buffer[pl_blockIdx].nominal_speed_sqr - mPlanner.block_buffer[pl_blockIdx].entry_speed_sqr);
}
}
else
{ // Triangle type
prep.accelerate_until = intersect_distance;
prep.decelerate_after = intersect_distance;
prep.maximum_speed = (float)System.Math.Sqrt(2.0 * mPlanner.block_buffer[pl_blockIdx].acceleration * intersect_distance + exit_speed_sqr);
}
}
else
{ // Deceleration-only type
prep.ramp_type = RAMP_DECEL;
// prep.decelerate_after = mPlanner.block_buffer[pl_blockIdx].millimeters;
prep.maximum_speed = prep.current_speed;
}
}
else
{ // Acceleration-only type
prep.accelerate_until = 0.0f;
// prep.decelerate_after = 0.0;
prep.maximum_speed = prep.exit_speed;
}
}
}
// Initialize new segment
//SB!Replaced prep_segment pointer with array access
//fixed (segment_t* prep_segment = &segment_buffer[segment_buffer_head])
// Set new segment to point to the current segment data block.
segment_t segment_buffer = new segment_t();
segment_buffer.st_block_index = prep.st_block_index;
/*------------------------------------------------------------------------------------
Compute the average velocity of this new segment by determining the total distance
traveled over the segment time DT_SEGMENT. The following code first attempts to create
a full segment based on the current ramp conditions. If the segment time is incomplete
when terminating at a ramp state change, the code will continue to loop through the
progressing ramp states to fill the remaining segment execution time. However, if
an incomplete segment terminates at the end of the velocity profile, the segment is
considered completed despite having a truncated execution time less than DT_SEGMENT.
The velocity profile is always assumed to progress through the ramp sequence:
acceleration ramp, cruising state, and deceleration ramp. Each ramp's travel distance
may range from zero to the length of the block. Velocity profiles can end either at
the end of planner block (typical) or mid-block at the end of a forced deceleration,
such as from a feed hold.
*/
float dt_max = DT_SEGMENT; // Maximum segment time
float dt = 0.0f; // Initialize segment time
float time_var = dt_max; // Time worker variable
float mm_var; // mm-Distance worker variable
float speed_var; // Speed worker variable
float mm_remaining = mPlanner.block_buffer[pl_blockIdx].millimeters; // New segment distance from end of block.
float minimum_mm = mm_remaining - prep.req_mm_increment; // Guarantee at least one step.
if (minimum_mm < 0.0) { minimum_mm = 0.0f; }
do
{
switch (prep.ramp_type)
{
case RAMP_ACCEL:
// NOTE: Acceleration ramp only computes during first do-while loop.
speed_var = mPlanner.block_buffer[pl_blockIdx].acceleration * time_var;
mm_remaining -= time_var * (prep.current_speed + 0.5f * speed_var);
if (mm_remaining < prep.accelerate_until)
{ // End of acceleration ramp.
// Acceleration-cruise, acceleration-deceleration ramp junction, or end of block.
mm_remaining = prep.accelerate_until; // NOTE: 0.0 at EOB
time_var = 2.0f * (mPlanner.block_buffer[pl_blockIdx].millimeters - mm_remaining) / (prep.current_speed + prep.maximum_speed);
if (mm_remaining == prep.decelerate_after) { prep.ramp_type = RAMP_DECEL; }
else { prep.ramp_type = RAMP_CRUISE; }
prep.current_speed = prep.maximum_speed;
}
else
{ // Acceleration only.
prep.current_speed += speed_var;
}
break;
case RAMP_CRUISE:
// NOTE: mm_var used to retain the last mm_remaining for incomplete segment time_var calculations.
// NOTE: If maximum_speed*time_var value is too low, round-off can cause mm_var to not change. To
// prevent this, simply enforce a minimum speed threshold in the planner.
mm_var = mm_remaining - prep.maximum_speed * time_var;
if (mm_var < prep.decelerate_after)
{ // End of cruise.
// Cruise-deceleration junction or end of block.
time_var = (mm_remaining - prep.decelerate_after) / prep.maximum_speed;
mm_remaining = prep.decelerate_after; // NOTE: 0.0 at EOB
prep.ramp_type = RAMP_DECEL;
}
else
{ // Cruising only.
mm_remaining = mm_var;
}
break;
default: // case RAMP_DECEL:
// NOTE: mm_var used as a misc worker variable to prevent errors when near zero speed.
speed_var = mPlanner.block_buffer[pl_blockIdx].acceleration * time_var; // Used as delta speed (mm/min)
if (prep.current_speed > speed_var)
{ // Check if at or below zero speed.
// Compute distance from end of segment to end of block.
mm_var = mm_remaining - time_var * (prep.current_speed - 0.5f * speed_var); // (mm)
if (mm_var > prep.mm_complete)
{ // Deceleration only.
mm_remaining = mm_var;
prep.current_speed -= speed_var;
break; // Segment complete. Exit switch-case statement. Continue do-while loop.
}
} // End of block or end of forced-deceleration.
time_var = 2.0f * (mm_remaining - prep.mm_complete) / (prep.current_speed + prep.exit_speed);
mm_remaining = prep.mm_complete;
break;
}
dt += time_var; // Add computed ramp time to total segment time.
if (dt < dt_max) { time_var = dt_max - dt; } // **Incomplete** At ramp junction.
else
{
if (mm_remaining > minimum_mm)
{ // Check for very slow segments with zero steps.
// Increase segment time to ensure at least one step in segment. Override and loop
// through distance calculations until minimum_mm or mm_complete.
dt_max += DT_SEGMENT;
time_var = dt_max - dt;
}
else
{
break; // **Complete** Exit loop. Segment execution time maxed.
}
}
} while (mm_remaining > prep.mm_complete); // **Complete** Exit loop. Profile complete.
/* -----------------------------------------------------------------------------------
Compute segment step rate, steps to execute, and apply necessary rate corrections.
NOTE: Steps are computed by direct scalar conversion of the millimeter distance
remaining in the block, rather than incrementally tallying the steps executed per
segment. This helps in removing floating point round-off issues of several additions.
However, since floats have only 7.2 significant digits, long moves with extremely
high step counts can exceed the precision of floats, which can lead to lost steps.
Fortunately, this scenario is highly unlikely and unrealistic in CNC machines
supported by Grbl (i.e. exceeding 10 meters axis travel at 200 step/mm).
*/
float steps_remaining = prep.step_per_mm * mm_remaining; // Convert mm_remaining to steps
short n_steps_remaining = (short)System.Math.Ceiling(steps_remaining); // Round-up current steps remaining
short last_n_steps_remaining = (short)System.Math.Ceiling(prep.steps_remaining); // Round-up last steps remaining
segment_buffer.n_step = (short)(last_n_steps_remaining - n_steps_remaining); // Compute number of steps to execute.
// Bail if we are at the end of a feed hold and don't have a step to execute.
if (segment_buffer.n_step == 0)
{
if (sys.state == STATE_HOLD)
{
// Less than one step to decelerate to zero speed, but already very close. AMASS
// requires full steps to execute. So, just bail.
prep.current_speed = 0.0f;
prep.dt_remainder = 0.0f;
prep.steps_remaining = n_steps_remaining;
mPlanner.block_buffer[pl_blockIdx].millimeters = prep.steps_remaining / prep.step_per_mm; // Update with full steps.
mPlanner.plan_cycle_reinitialize();
sys.setState(STATE_QUEUED);
return false; // Segment not generated, but current step data still retained.
}
}
// Compute segment step rate. Since steps are integers and mm distances traveled are not,
// the end of every segment can have a partial step of varying magnitudes that are not
// executed, because the stepper ISR requires whole steps due to the AMASS algorithm. To
// compensate, we track the time to execute the previous segment's partial step and simply
// apply it with the partial step distance to the current segment, so that it minutely
// adjusts the whole segment rate to keep step output exact. These rate adjustments are
// typically very small and do not adversely effect performance, but ensures that Grbl
// outputs the exact acceleration and velocity profiles as computed by the planner.
dt += prep.dt_remainder; // Apply previous segment partial step execute time
float inv_rate = dt / (last_n_steps_remaining - steps_remaining); // Compute adjusted step rate inverse
prep.dt_remainder = (n_steps_remaining - steps_remaining) * inv_rate; // Update segment partial step time
// Compute CPU cycles per step for the prepped segment.
uint cycles = (uint)System.Math.Ceiling((NutsAndBolts.TICKS_PER_MICROSECOND * 1000000.0 * 60) * inv_rate); // (cycles/step)
if (ADAPTIVE_MULTI_AXIS_STEP_SMOOTHING)
{
// Compute step timing and multi-axis smoothing level.
// NOTE: AMASS overdrives the timer with each level, so only one prescalar is required.
if (cycles < AMASS_LEVEL1) { segment_buffer.amass_level = 0; }
else
{
if (cycles < AMASS_LEVEL2) { segment_buffer.amass_level = 1; }
else if (cycles < AMASS_LEVEL3) { segment_buffer.amass_level = 2; }
else { segment_buffer.amass_level = 3; }
cycles >>= segment_buffer.amass_level;
segment_buffer.n_step <<= segment_buffer.amass_level;
}
if (cycles < (1 << 16)) { segment_buffer.cycles_per_tick = (ushort)cycles; } // < 65536 (4.1ms @ 16MHz)
else { segment_buffer.cycles_per_tick = 0xffff; } // Just set the slowest speed possible.
}
else
{
// Compute step timing and timer prescalar for normal step generation.
if (cycles < (1 << 16))
{ // < 65536 (4.1ms @ 16MHz)
segment_buffer.prescaler = 1; // prescaler: 0
segment_buffer.cycles_per_tick = (ushort)cycles;
}
else if (cycles < (1UL << 19))
{ // < 524288 (32.8ms@16MHz)
segment_buffer.prescaler = 2; // prescaler: 8
segment_buffer.cycles_per_tick = (ushort)(cycles >> 3);
}
else
{
segment_buffer.prescaler = 3; // prescaler: 64
if (cycles < (1UL << 22))
{ // < 4194304 (262ms@16MHz)
segment_buffer.cycles_per_tick = (ushort)(cycles >> 6);
}
else
{ // Just set the slowest speed possible. (Around 4 step/sec.)
segment_buffer.cycles_per_tick = 0xffff;
}
}
}
// Segment complete! Increment segment buffer indices.
//mLaserCatHardware.StoreSegment(segment_buffer);
bufferSpace = mLaserCatHardware.StoreSegment(segment_buffer);
// Setup initial conditions for next segment.
if (mm_remaining > prep.mm_complete)
{
// Normal operation. Block incomplete. Distance remaining in block to be executed.
mPlanner.block_buffer[pl_blockIdx].millimeters = mm_remaining;
prep.steps_remaining = steps_remaining;
}
else
{
// End of planner block or forced-termination. No more distance to be executed.
if (mm_remaining > 0.0)
{ // At end of forced-termination.
// Reset prep parameters for resuming and then bail.
// NOTE: Currently only feed holds qualify for this scenario. May change with overrides.
prep.current_speed = 0.0f;
prep.dt_remainder = 0.0f;
prep.steps_remaining = (float)System.Math.Ceiling(steps_remaining);
mPlanner.block_buffer[pl_blockIdx].millimeters = prep.steps_remaining / prep.step_per_mm; // Update with full steps.
mPlanner.plan_cycle_reinitialize();
sys.setState(STATE_QUEUED); // End cycle.
return false; // Bail!
// TODO: Try to move QUEUED setting into cycle re-initialize.
}
else
{ // End of planner block
// The planner block is complete. All steps are set to be executed in the segment buffer.
//pl_block = null;
pl_blockIdx = -1;
mPlanner.plan_discard_current_block();
}
}
}
return false;
}