/// <summary>
/// Read 1 of 6 available module addresses
/// </summary>
public byte[] GetAddress(AddressSlot slot, int width)
{
CheckIsInitialized();
AddressWidth.Check(width);
var read = Execute(Commands.R_REGISTER, (byte)slot, new byte[width]);
var result = new byte[read.Length - 1];
Array.Copy(read, 1, result, 0, result.Length);
return(result);
}
/// <summary>
/// Set one of 6 available module addresses
/// </summary>
public void SetAddress(AddressSlot slot, byte[] address)
{
CheckIsInitialized();
AddressWidth.Check(address);
Execute(Commands.W_REGISTER, (byte)slot, address);
if (slot == AddressSlot.Zero)
{
_slot0Address = address;
}
}
/// <summary>
/// Configure the module basic settings. Module needs to be initiaized.
/// </summary>
/// <param name="address">RF address (3-5 bytes). The width of this address determins the width of all addresses used for sending/receiving.</param>
/// <param name="channel">RF channel (0-127)</param>
/// <param name="dataRate">Data Rate to use</param>
public void Configure(byte[] address, byte channel, DataRate dataRate)
{
CheckIsInitialized();
AddressWidth.Check(address);
// Set radio channel
Execute(Commands.W_REGISTER, Registers.RF_CH,
new[]
{
(byte)(channel & 0x7F) // channel is 7 bits
});
// Set Data rate
var regValue = Execute(Commands.R_REGISTER, Registers.RF_SETUP, new byte[1])[1];
switch (dataRate)
{
case DataRate.DR1Mbps:
regValue &= (byte)~(1 << Bits.RF_DR_LOW); // 0
regValue &= (byte)~(1 << Bits.RF_DR_HIGH); // 0
break;
case DataRate.DR2Mbps:
regValue &= (byte)~(1 << Bits.RF_DR_LOW); // 0
regValue |= (byte)(1 << Bits.RF_DR_HIGH); // 1
break;
case DataRate.DR250kbps:
regValue |= (byte)(1 << Bits.RF_DR_LOW); // 1
regValue &= (byte)~(1 << Bits.RF_DR_HIGH); // 0
break;
default:
throw new ArgumentOutOfRangeException("dataRate");
}
Execute(Commands.W_REGISTER, Registers.RF_SETUP, new[] { regValue });
// Enable dynamic payload length
Execute(Commands.W_REGISTER, Registers.FEATURE,
new[]
{
(byte)(1 << Bits.EN_DPL)
});
// Set auto-ack
Execute(Commands.W_REGISTER, Registers.EN_AA,
new[]
{
(byte)(1 << Bits.ENAA_P0 |
1 << Bits.ENAA_P1)
});
// Set dynamic payload length for pipes
Execute(Commands.W_REGISTER, Registers.DYNPD,
new[]
{
(byte)(1 << Bits.DPL_P0 |
1 << Bits.DPL_P1)
});
// Flush RX FIFO
Execute(Commands.FLUSH_RX, 0x00, new byte[0]);
// Flush TX FIFO
Execute(Commands.FLUSH_TX, 0x00, new byte[0]);
// Clear IRQ Masks
Execute(Commands.W_REGISTER, Registers.STATUS,
new[]
{
(byte)(1 << Bits.MASK_RX_DR |
1 << Bits.MASK_TX_DS |
1 << Bits.MAX_RT)
});
// Set default address
Execute(Commands.W_REGISTER, Registers.SETUP_AW,
new[]
{
AddressWidth.Get(address)
});
// Set module address
_slot0Address = address;
Execute(Commands.W_REGISTER, (byte)AddressSlot.Zero, address);
// Set retransmission values
Execute(Commands.W_REGISTER, Registers.SETUP_RETR,
new[]
{
(byte)(0x0F << Bits.ARD |
0x0F << Bits.ARC)
});
// Setup, CRC enabled, Power Up, PRX
SetReceiveMode();
}