/// <summary>
/// Case 9: Calculation of internal forces in symmetric section for given state of strain with inclined neutral axis
/// </summary>
public void Case9()
{
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.6);
geometry.Add(0.3, 0.6);
geometry.Add(0.3, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.012 * 0.012 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelBiLinear(25e6, 0.003, 28e9, 0.002);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(550e6, 0.1, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveForces(ResultType.Section, 0.0025, -0.00383423, 0.34906585);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 9: Calculation of internal forces in symmetric section for given state of strain with inclined neutral axis ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
}
/// <summary>
/// Case 14: Calculation of capacity state in symmetric section for bidirectional bending with axial force
/// </summary>
public void Case14()
{
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.3, 0.0);
geometry.Add(0.3, 0.45);
geometry.Add(0.0, 0.45);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
rebars.Add(new Rebar(0.15, 0.04, 0.025977 * 0.025977 * Math.PI / 4.0));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelRectangular(21.36e6, 0.0035, 35e9, 0.8);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(310e6, 0.01, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistance(200E3, -96E3, -24E3);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
double angle = solver.GetNeutralAxisAngle();
double dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 14: Calculation of capacity state in symmetric section for bidirectional bending with axial force ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
}
/// <summary>
/// Case 4: Calculation of internal forces for given state of strain in the section and bilinear model of concrete
/// Case 4a, Case 4b and Case 4c - common geometry, concrete and steel parameters different rebars and calculation
/// </summary>
public void Case4()
{
// Case 4a:
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.6);
geometry.Add(0.3, 0.6);
geometry.Add(0.3, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.016 * 0.016 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelBiLinear(30e6, 0.0035, 32e9, 0.002);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(400e6, 0.1, 205e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveForces(ResultType.Section, 0.0035, 0.0005);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 4a: Calculation of internal forces for given state of strain in the section and bilinear model of concrete ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
output.Text = output.Text + sb.AppendLine();
//
// Case 4b
rebars.Clear();
rebarArea = 0.032 * 0.032 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
solver.SetRebars(rebars);
//calulation
solver.SolveForces(ResultType.Section, 0.0035, -0.02936558);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 4b: Calculation of internal forces for given state of strain in the section and bilinear model of concrete ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
output.Text = output.Text + sb.AppendLine();
//
// Case 4c
rebars.Clear();
rebarArea = 0.032 * 0.032 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
solver.SetRebars(rebars);
//calulation
solver.SolveForces(ResultType.Section, 0.0015, -0.002);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 4c: Calculation of internal forces for given state of strain in the section and bilinear model of concrete ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
output.Text = output.Text + sb.AppendLine();
}
RCSolver solver; // solver
/// <summary>
/// Initializes a new instance of the new RC calculation helper object.
/// </summary>
/// <param name="type">The type of the cross-section</param>
/// <param name="rcGeometry">Set of geometry parameters.</param>
/// <param name="coverTop">The top cover - to the reinforcement ceneter.</param>
/// <param name="coverBottom">The top cover - to the reinforcement ceneter.</param>
private RcVerificationHelperUtility(SectionShapeType type, ref Geometry rcGeometry, double coverTop, double coverBottom)
{
double totalHeight = 0; // the height of the cross section
double totalWidth = 0; // the width of the cross section
noTopBottom = 5; // initial value of the number of bars on top and bottom
noLeftRight = noTopBottom - 2; // initial value of the number of bars on left and right
solverGeometry = new Geometry(); // initialization of new geometry
rebars = new List <Rebar>(); // initialization of rebars list
rebarsSide = new List <CrossSectionSide>(); // initialization of bars position list
crossSectionType = type; // set of section type
rebarCover = Math.Max(coverTop, coverBottom); // set of maximum cover
rebarCoverTop = coverTop; // set of top cover
rebarCoverBottom = coverBottom; // set of bottom cover
// In the input geometry left bottom corner is searched.
// The maximum and minimum values for x and y coordinates
int leftBottomIndex = 0;
double x = Double.MaxValue;
double y = Double.MaxValue;
double xMin = Double.MaxValue;
double yMin = Double.MaxValue;
double xMax = Double.MinValue;
double yMax = Double.MinValue;
int i = 0;
int count = rcGeometry.Count;
Point2D p = new Point2D(0, 0);
for (i = 0; i < count; i++)
{
p = rcGeometry.Point(i);
xMin = Math.Min(xMin, p.X);
yMin = Math.Min(yMin, p.Y);
xMax = Math.Max(xMax, p.X);
yMax = Math.Max(yMax, p.Y);
if ((p.X - x) < geometryEpsilon)
{
if ((p.Y - y) < geometryEpsilon)
{
y = p.Y;
x = p.X;
leftBottomIndex = i;
}
}
}
totalHeight = (yMax - yMin);
totalWidth = (xMax - xMin);
// The first point of new geometry will be in the bottom left point of geometry.
// This is made for easy detailing.
if (0 != leftBottomIndex)
{
solverGeometry.Clear();
for (i = leftBottomIndex; i < count; i++)
{
p = rcGeometry.Point(i);
solverGeometry.Add(p.X, p.Y);
}
count = leftBottomIndex;
for (i = 0; i < count; i++)
{
p = rcGeometry.Point(i);
solverGeometry.Add(p.X, p.Y);
}
}
else
{
solverGeometry = rcGeometry;
}
// The orientation is changed if it is necessary.
if (solverGeometry.isClockwiseOrientation()) // clockwise direction
{
count = solverGeometry.Count - 1;
Geometry tmpGeometry = new Geometry();
p = solverGeometry.Point(0);
tmpGeometry.Add(p.X, p.Y);
for (i = count; i > 0; i--)
{
p = solverGeometry.Point(i);
tmpGeometry.Add(p.X, p.Y);
}
solverGeometry = tmpGeometry;
}
solver = RCSolver.CreateNewSolver(solverGeometry); // solver with geometry redy to use.
}
/// <summary>
/// Case 16: Calculation of capacity state in symmetric section for fixed axial force
/// </summary>
public void Case16()
{
// Case 16a
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.6);
geometry.Add(0.3, 0.6);
geometry.Add(0.3, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.040 * 0.040 * Math.PI / 4.0;
rebars.Add(new Rebar(0.03, 0.03, rebarArea));
rebars.Add(new Rebar(0.03, 0.57, rebarArea));
rebars.Add(new Rebar(0.27, 0.57, rebarArea));
rebars.Add(new Rebar(0.27, 0.03, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelRectangular(17.12e6, 0.0035, 32e9, 0.8);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(310e6, 0.025, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistanceM(678E3, Axis.x, false);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
double angle = solver.GetNeutralAxisAngle();
double dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 16a: Calculation of capacity state in symmetric section for fixed axial force");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
// Case 16b
// geometry definition
geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.3);
geometry.Add(0.6, 0.3);
geometry.Add(0.6, 0.0);
// rebars definition
rebars.Clear();
rebarArea = 0.036 * 0.036 * Math.PI / 4.0;
rebars.Add(new Rebar(0.09, 0.06, rebarArea));
rebars.Add(new Rebar(0.09, 0.12, rebarArea));
rebars.Add(new Rebar(0.09, 0.18, rebarArea));
rebars.Add(new Rebar(0.09, 0.24, rebarArea));
rebars.Add(new Rebar(0.51, 0.06, rebarArea));
rebars.Add(new Rebar(0.51, 0.12, rebarArea));
rebars.Add(new Rebar(0.51, 0.18, rebarArea));
rebars.Add(new Rebar(0.51, 0.24, rebarArea));
// steel parameters
steel = new Steel();
steel.DesignStrength = 420e6;
steel.HardeningFactor = 1.0;
steel.ModulusOfElasticity = 200e9;
steel.StrainUltimateLimit = 0.025;
// solver creation and parameterization
solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistanceM(1700E3, Axis.y, true);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
angle = solver.GetNeutralAxisAngle();
dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 16b: Calculation of capacity state in symmetric section for fixed axial force");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
}
/// <summary>
/// Case 10: Calculation of capacity state in symmetric section for bending moment Mx
/// </summary>
public void Case10()
{
// Case 10a
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.6);
geometry.Add(0.3, 0.6);
geometry.Add(0.3, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.020 * 0.020 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelRectangular(20e6, 0.0035, 30e9, 0.9);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(500e6, 0.075, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistanceM(0, Axis.x, false);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
double angle = solver.GetNeutralAxisAngle();
double dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 10a: Calculation of internal forces in symmetric section for given state of strain with inclined neutral axis");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
// Case 10b
// rebars definition
rebarArea = 0.032 * 0.032 * Math.PI / 4.0;
rebars.Clear();
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
concrete.SetStrainStressModelParabolicRectangular(30e6, 0.0035, 32e9, 0.0020);
// steel parameters
steel.DesignStrength = 400e6;
steel.StrainUltimateLimit = 0.1;
// solver parameterization
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistanceM(0, Axis.x, false);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 10b: Calculation of internal forces in symmetric section for given state of strain with inclined neutral axis ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
}
/// </structural_toolkit_2015>
/// <summary>
/// Initializes a new instance of the new RC calculation helper object.
/// </summary>
/// <param name="type">The type of the cross-section</param>
/// <param name="rcGeometry">Set of geometry parameters.</param>
/// <param name="coverTop">The top cover - to the reinforcement ceneter.</param>
/// <param name="coverBottom">The top cover - to the reinforcement ceneter.</param>
private RcVerificationHelperUtility(SectionShapeType type, ref Geometry rcGeometry, double coverTop, double coverBottom)
{
totalHeight = 0; // initial value of the height of the cross section
totalWidth = 0; // initial value of the width of the cross section
noTopBottom = 5; // initial value of the number of bars on top and bottom
noLeftRight = noTopBottom - 2; // initial value of the number of bars on left and right
solverGeometry = new Geometry(); // initialization of new geometry
rebars = new List <Rebar>(); // initialization of rebars list
rebarsSide = new List <CrossSectionSide>(); // initialization of bars position list
crossSectionType = type; // set of section type
rebarCover = Math.Max(coverTop, coverBottom); // set of maximum cover
rebarCoverTop = coverTop; // set of top cover
rebarCoverBottom = coverBottom; // set of bottom cover
/// <structural_toolkit_2015>
edgesForReinforcement = new Dictionary <CrossSectionSide, Tuple <int, int> >();
geometryMinX = Double.MaxValue;
geometryMinY = Double.MaxValue;
geometryMaxX = Double.MinValue;
geometryMaxY = Double.MinValue;
/// </structural_toolkit_2015>
// Top,bottom, lreft and right edges are searched, based on maximum and minimum values for x and y coordinates
/// <structural_toolkit_2015>
solverGeometry = rcGeometry;
int count = solverGeometry.Count;
Point2D p = new Point2D(0, 0);
// The orientation is changed if it is necessary.
if (solverGeometry.isClockwiseOrientation()) // clockwise direction
{
Geometry tmpGeometry = new Geometry();
p = solverGeometry.Point(0);
tmpGeometry.Add(p.X, p.Y);
for (int i = count - 1; i > 0; i--)
{
p = solverGeometry.Point(i);
tmpGeometry.Add(p.X, p.Y);
}
solverGeometry = tmpGeometry;
}
foreach (Point2D p2D in solverGeometry)
{
geometryMinX = Math.Min(geometryMinX, p2D.X);
geometryMinY = Math.Min(geometryMinY, p2D.Y);
geometryMaxX = Math.Max(geometryMaxX, p2D.X);
geometryMaxY = Math.Max(geometryMaxY, p2D.Y);
}
Tuple <int, int> curentTuple = null;
for (int i = 0; i < count; i++)
{
p = solverGeometry.Point(i);
// Left
if (CompareGeomety(geometryMinX, p.X) >= 0)
{
if (!edgesForReinforcement.ContainsKey(CrossSectionSide.Left) || CompareGeomety(geometryMinX, p.X) > 0)
{
curentTuple = new Tuple <int, int>(i, i);
}
else
{
if (CompareGeomety(p.Y, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Left].Item2).Y) > 0)
{
curentTuple = new Tuple <int, int>(edgesForReinforcement[CrossSectionSide.Left].Item1, i);
}
else if (CompareGeomety(p.Y, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Left].Item1).Y) < 0)
{
curentTuple = new Tuple <int, int>(i, edgesForReinforcement[CrossSectionSide.Left].Item2);
}
}
edgesForReinforcement.Remove(CrossSectionSide.Left);
edgesForReinforcement.Add(CrossSectionSide.Left, curentTuple);
}
// Right
if (CompareGeomety(geometryMaxX, p.X) <= 0)
{
if (!edgesForReinforcement.ContainsKey(CrossSectionSide.Right) || CompareGeomety(geometryMaxX, p.X) < 0)
{
curentTuple = new Tuple <int, int>(i, i);
}
else
{
if (CompareGeomety(p.Y, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Right].Item2).Y) > 0)
{
curentTuple = new Tuple <int, int>(edgesForReinforcement[CrossSectionSide.Right].Item1, i);
}
else if (CompareGeomety(p.Y, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Right].Item1).Y) < 0)
{
curentTuple = new Tuple <int, int>(i, edgesForReinforcement[CrossSectionSide.Right].Item2);
}
}
edgesForReinforcement.Remove(CrossSectionSide.Right);
edgesForReinforcement.Add(CrossSectionSide.Right, curentTuple);
}
// Top
if (CompareGeomety(geometryMaxY, p.Y) <= 0)
{
if (!edgesForReinforcement.ContainsKey(CrossSectionSide.Top) || CompareGeomety(geometryMaxY, p.Y) < 0)
{
curentTuple = new Tuple <int, int>(i, i);
}
else
{
if (CompareGeomety(p.X, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Top].Item2).X) > 0)
{
curentTuple = new Tuple <int, int>(edgesForReinforcement[CrossSectionSide.Top].Item1, i);
}
else if (CompareGeomety(p.X, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Top].Item1).X) < 0)
{
curentTuple = new Tuple <int, int>(i, edgesForReinforcement[CrossSectionSide.Top].Item2);
}
}
edgesForReinforcement.Remove(CrossSectionSide.Top);
edgesForReinforcement.Add(CrossSectionSide.Top, curentTuple);
}
// Bottom
if (CompareGeomety(geometryMinY, p.Y) >= 0)
{
if (!edgesForReinforcement.ContainsKey(CrossSectionSide.Bottom) || CompareGeomety(geometryMinY, p.Y) > 0)
{
curentTuple = new Tuple <int, int>(i, i);
}
else
{
if (CompareGeomety(p.X, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Bottom].Item2).X) > 0)
{
curentTuple = new Tuple <int, int>(edgesForReinforcement[CrossSectionSide.Bottom].Item1, i);
}
else if (CompareGeomety(p.X, solverGeometry.Point(edgesForReinforcement[CrossSectionSide.Bottom].Item1).X) < 0)
{
curentTuple = new Tuple <int, int>(i, edgesForReinforcement[CrossSectionSide.Bottom].Item2);
}
}
edgesForReinforcement.Remove(CrossSectionSide.Bottom);
edgesForReinforcement.Add(CrossSectionSide.Bottom, curentTuple);
}
}
/// </structural_toolkit_2015>
totalHeight = (geometryMaxY - geometryMinY);
totalWidth = (geometryMaxX - geometryMinX);
solver = RCSolver.CreateNewSolver(solverGeometry); // solver with geometry redy to use.
}
/// <summary>
/// Case 12: Calculation of capacity state in symmetric section for bending moment Mx with axial force
/// </summary>
public void Case12()
{
// Case 12a
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.3, 0.0);
geometry.Add(0.3, 0.6);
geometry.Add(0.0, 0.6);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.012 * 0.012 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelLinear(20e6, 0.0035, 30e9);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(500e6, 0.075, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistance(43979.98E3, -3465.40E3, 0);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
double angle = solver.GetNeutralAxisAngle();
double dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 12a: Calculation of capacity state in symmetric section for bending moment Mx with axial force ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
// Case 12b
// rebars definition
rebars.Clear();
rebarArea = 0.016 * 0.016 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.55, rebarArea));
rebars.Add(new Rebar(0.25, 0.05, rebarArea));
// concrete parameters
concrete.SetStrainStressModelBiLinear(30e6, 0.0035, 32e9, 0.0020);
// steel parameters
steel.DesignStrength = 400e6;
steel.HardeningFactor = 1.0;
steel.ModulusOfElasticity = 205e9;
steel.StrainUltimateLimit = 0.1;
// solver parameterization
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistance(114.8397E3, -5.634275E3, 0);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 12b:Calculation of capacity state in symmetric section for bending moment Mx with axial force");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
// Case 12c
// concrete parameters
concrete.SetStrainStressModelPowerRectangular(30e6, 0.0035, 32e9, 0.002, 1.4);
// steel parameters
steel.DesignStrength = 400e6;
steel.HardeningFactor = 1.0;
steel.ModulusOfElasticity = 200e9;
steel.StrainUltimateLimit = 0.1;
// solver parameterization
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistance(4.41023E3, -0.1662045455E3, 0);
// result for rebars
forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
Acc = solver.GetConcreteStressArea();
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 12c: Calculation of capacity state in symmetric section for bending moment Mx with axial force ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
}
/// <summary>
/// Case 7 Calculation of internal forces for given state of strain in the section and inclined branch model of steel
/// </summary>
public void Case7()
{
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.6);
geometry.Add(0.3, 0.6);
geometry.Add(0.3, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
rebars.Add(new Rebar(0.05, 0.05, 0.032 * 0.032 * Math.PI / 4.0));
rebars.Add(new Rebar(0.15, 0.05, 0.032 * 0.032 * Math.PI / 4.0));
rebars.Add(new Rebar(0.25, 0.05, 0.032 * 0.032 * Math.PI / 4.0));
rebars.Add(new Rebar(0.05, 0.15, 0.020 * 0.020 * Math.PI / 4.0));
rebars.Add(new Rebar(0.25, 0.15, 0.020 * 0.020 * Math.PI / 4.0));
rebars.Add(new Rebar(0.05, 0.55, 0.012 * 0.012 * Math.PI / 4.0));
rebars.Add(new Rebar(0.25, 0.55, 0.012 * 0.012 * Math.PI / 4.0));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelLinear(20e6, 0.0035, 30e9);
// steel parameters
Steel steel = new Steel();
steel.SetModelWithHardening(500e6, 0.075, 200e9, 1.05);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveForces(ResultType.Section, 0.0035, -0.0070);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 7 Calculation of internal forces for given state of strain in the section and inclined branch model of steel ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
}
/// <summary>
/// Case 15: Calculation of capacity state in asymmetric section for bidirectional bending with axial force
/// </summary>
public void Case15()
{
// Case 15a
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.00, 0.00);
geometry.Add(0.00, 0.60);
geometry.Add(0.25, 0.60);
geometry.Add(0.25, 0.25);
geometry.Add(0.70, 0.25);
geometry.Add(0.70, 0.00);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
double rebarArea = 0.020 * 0.020 * Math.PI / 4.0;
rebars.Add(new Rebar(0.05, 0.05, rebarArea));
rebars.Add(new Rebar(0.05, 0.55, rebarArea));
rebars.Add(new Rebar(0.20, 0.55, rebarArea));
rebars.Add(new Rebar(0.20, 0.05, rebarArea));
rebars.Add(new Rebar(0.65, 0.05, rebarArea));
rebars.Add(new Rebar(0.65, 0.20, rebarArea));
rebars.Add(new Rebar(0.05, 0.20, rebarArea));
// concrete parameters
Concrete concrete = new Concrete();
concrete.SetStrainStressModelRectangular(20e6, 0.0035, 35e9, 0.8);
// steel parameters
Steel steel = new Steel();
steel.SetModelIdealElastoPlastic(310e6, 0.075, 200e9);
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for rebars
SetOfForces forcesRebar = solver.GetInternalForces(ResultType.Rebars);
// result for concrete
SetOfForces forcesConcrete = solver.GetInternalForces(ResultType.Concrete);
Point2D Gcc = solver.GetStressGravityCenter(ResultType.Concrete);
double Acc = solver.GetConcreteStressArea();
// result for RC section
SetOfForces forces = solver.GetInternalForces(ResultType.Section);
double angle = solver.GetNeutralAxisAngle();
double dist = solver.GetNeutralAxisDistance();
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15a: Calculation of capacity state in asymmetric section for bidirectional bending with axial force ");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ns", forcesRebar.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxs", forcesRebar.MomentX, 6));
sb.AppendLine(FormatOutput("Mys", forcesRebar.MomentY, 6));
sb.AppendLine(FormatOutput("Ac", Acc, 6));
sb.AppendLine(FormatOutput("Gcx", Gcc.X, 6));
sb.AppendLine(FormatOutput("Gcy", Gcc.Y, 6));
sb.AppendLine(FormatOutput("Nc", forcesConcrete.AxialForce, 6));
sb.AppendLine(FormatOutput("Mxc", forcesConcrete.MomentX, 6));
sb.AppendLine(FormatOutput("Myc", forcesConcrete.MomentY, 6));
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
sb.AppendLine(FormatOutput("dist", dist, 6));
sb.AppendLine(FormatOutput("angle", angle, 6));
// Case 15b
// concrete parameters (rectangular)
concrete.SetStrainStressModelRectangular(20e6, 0.0035, 35e9, 0.8);
// solver parameterization
solver.SetConcrete(concrete);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15b: Calculation of capacity state in asymmetric section for bidirectional bending with axial force (rectangular)");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
// concrete parameters(linear)
concrete.SetStrainStressModelLinear(25e6, 0.0035, 32e9);
// solver parameterization
solver.SetConcrete(concrete);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15b: Calculation of capacity state in asymmetric section for bidirectional bending with axial force (linear)");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
// concrete parameters (bilinear)
concrete.SetStrainStressModelBiLinear(25e6, 0.0035, 32e9, 0.0020);
// solver parameterization
solver.SetConcrete(concrete);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15b: Calculation of capacity state in asymmetric section for bidirectional bending with axial force (bilinear)");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
// concrete parameters (parabolic-rectangular)
concrete.SetStrainStressModelParabolicRectangular(25e6, 0.0035, 32e9, 0.0020);
// solver parameterization
solver.SetConcrete(concrete);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15b: Calculation of capacity state in asymmetric section for bidirectional bending with axial force (parabolic-rectangular)");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
// concrete parameters (power-rectangular)
concrete.SetStrainStressModelPowerRectangular(25e6, 0.0035, 32e9, 0.002, 1.5);
// solver parameterization
solver.SetConcrete(concrete);
//calulation
solver.SolveResistance(72.4471E3, -28.9825E3, 2.5743E3);
// result for RC section
forces = solver.GetInternalForces(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 15b: Calculation of capacity state in asymmetric section for bidirectional bending with axial force (parabolic-rectangular)");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("N", forces.AxialForce, 6));
sb.AppendLine(FormatOutput("Mx", forces.MomentX, 6));
sb.AppendLine(FormatOutput("My", forces.MomentY, 6));
}
/// <summary>
/// Case 1: Cross section characteristics
/// </summary>
public void Case1()
{
// geometry definition
Geometry geometry = new Geometry();
geometry.Add(0.0, 0.0);
geometry.Add(0.0, 0.2);
geometry.Add(0.2, 0.2);
geometry.Add(0.2, 0.6);
geometry.Add(0.5, 0.6);
geometry.Add(0.5, 0.3);
geometry.Add(0.8, 0.3);
geometry.Add(0.8, 0.0);
// rebars definition
List <Rebar> rebars = new List <Rebar>();
// rebar area A = d*d*pi/4
rebars.Add(new Rebar(0.05, 0.05, 0.010 * 0.010 * Math.PI / 4.0));
rebars.Add(new Rebar(0.75, 0.05, 0.012 * 0.012 * Math.PI / 4.0));
rebars.Add(new Rebar(0.75, 0.25, 0.020 * 0.020 * Math.PI / 4.0));
rebars.Add(new Rebar(0.45, 0.55, 0.050 * 0.050 * Math.PI / 4.0));
rebars.Add(new Rebar(0.25, 0.55, 0.020 * 0.020 * Math.PI / 4.0));
rebars.Add(new Rebar(0.05, 0.15, 0.015 * 0.015 * Math.PI / 4.0));
// concrete parameters
Concrete concrete = new Concrete();
concrete.ModulusOfElasticity = 30e9;
// steel parameters
Steel steel = new Steel();
steel.ModulusOfElasticity = 200e9;
// solver creation and parameterization
RCSolver solver = RCSolver.CreateNewSolver(geometry);
solver.SetRebars(rebars);
solver.SetConcrete(concrete);
solver.SetSteel(steel);
// result for concrete
double Ac = solver.GetArea(ResultType.Concrete);
Point2D Cc = solver.GetCenterOfInertia(ResultType.Concrete);
double Icx = solver.GetMomentOfInertiaX(ResultType.Concrete);
double Icy = solver.GetMomentOfInertiaY(ResultType.Concrete);
// result for rebars
double As = solver.GetArea(ResultType.Rebars);
Point2D Cs = solver.GetCenterOfInertia(ResultType.Rebars);
double Isx = solver.GetMomentOfInertiaX(ResultType.Rebars);
double Isy = solver.GetMomentOfInertiaY(ResultType.Rebars);
// result for reduced
double Aeff = solver.GetArea(ResultType.Section);
Point2D Ceff = solver.GetCenterOfInertia(ResultType.Section);
double Ieffx = solver.GetMomentOfInertiaX(ResultType.Section);
double Ieffy = solver.GetMomentOfInertiaY(ResultType.Section);
// result presentation
sb.AppendLine();
sb.AppendLine(decoration);
sb.AppendLine("Case 1: Cross section characteristics");
sb.AppendLine(decoration);
sb.AppendLine(FormatOutput("Ac", Ac, 6));
sb.AppendLine(FormatOutput("Ccx", Cc.X, 6));
sb.AppendLine(FormatOutput("Ccy", Cc.Y, 6));
sb.AppendLine(FormatOutput("Icx", Icx, 6));
sb.AppendLine(FormatOutput("Icy", Icy, 6));
sb.AppendLine(FormatOutput("As", As, 6));
sb.AppendLine(FormatOutput("Csx", Cs.X, 6));
sb.AppendLine(FormatOutput("Csy", Cs.Y, 6));
sb.AppendLine(FormatOutput("Isx", Isx, 6));
sb.AppendLine(FormatOutput("Isy", Isy, 6));
sb.AppendLine(FormatOutput("Aeff", Aeff, 6));
sb.AppendLine(FormatOutput("Ceffx", Ceff.X, 6));
sb.AppendLine(FormatOutput("Ceffy", Ceff.Y, 6));
sb.AppendLine(FormatOutput("Ieffx", Ieffx, 6));
sb.AppendLine(FormatOutput("Ieffy", Ieffy, 6));
}