/// <summary> /// Initializes a new instance of the NAThermStateBody class. /// </summary> public NAThermStateBody(NASetpoint setpoint = default(NASetpoint), NASetpoint setpointOrder = default(NASetpoint), NAThermProgram thermProgram = default(NAThermProgram), IList <NAThermProgram> thermProgramBackup = default(IList <NAThermProgram>), NAThermProgram thermProgramOrder = default(NAThermProgram), int?thermOrientation = default(int?), int?thermRelayCmd = default(int?), int?batteryVp = default(int?), int?rfStatus = default(int?), int?plugConnectedBoiler = default(int?), bool?udpConn = default(bool?), int?lastThermSeen = default(int?), int?lastPlugSeen = default(int?), int?wifiStatus = default(int?), NAThermMeasure measured = default(NAThermMeasure)) { Setpoint = setpoint; SetpointOrder = setpointOrder; ThermProgram = thermProgram; ThermProgramBackup = thermProgramBackup; ThermProgramOrder = thermProgramOrder; ThermOrientation = thermOrientation; ThermRelayCmd = thermRelayCmd; BatteryVp = batteryVp; RfStatus = rfStatus; PlugConnectedBoiler = plugConnectedBoiler; UdpConn = udpConn; LastThermSeen = lastThermSeen; LastPlugSeen = lastPlugSeen; WifiStatus = wifiStatus; Measured = measured; CustomInit(); }
/// <summary> /// Initializes a new instance of the NAThermostat class. /// </summary> /// <param name="type">Included in every device or module. It defines /// the type of the device/module. Its values are among : /// NAMain : for the base station /// NAModule1 : for the outdoor module /// NAModule4 : for the additionnal indoor module /// NAModule3 : for the rain gauge module /// NAPlug : for the thermostat relay/plug /// NATherm1 : for the thermostat module /// </param> /// <param name="rfStatus">"It contains the current radio status. The /// different thresholds to take into account are :" | /// RADIO_THRESHOLD_SIGNAL_LOW = 90 /// RADIO_THRESHOLD_SIGNAL_MEDIUM = 80 /// RADIO_THRESHOLD_SIGNAL_HIGH = 70 /// RADIO_THRESHOLD_SIGNAL_FULL = 60 /// </param> /// <param name="batteryVp">It contains the current battery status. The /// threshold depends on the kind of module, below is the list of the /// different threshold to take into account according the module type. /// "Indoor module Battery range: 6000 ... 4200" | /// INDOOR_BATTERY_LEVEL_FULL = 5640 /// INDOOR_BATTERY_LEVEL_HIGH = 5280 /// INDOOR_BATTERY_LEVEL_MEDIUM = 4920 /// INDOOR_BATTERY_LEVEL_LOW = 4560 /// "Below 4560: very low" | /// /// "Raingauge and outdoor module Battery range: 6000 ... 3600" | /// BATTERY_LEVEL_FULL = 5500 /// BATTERY_LEVEL_HIGH = 5000 /// BATTERY_LEVEL_MEDIUM = 4500 /// BATTERY_LEVEL_LOW = 4000 /// "Below 4000: very low" | /// /// "Thermostat Battery range: 4500 ... 3000" | /// THERMOSTAT_BATTERY_LEVEL_FULL = 4100 /// THERMOSTAT_BATTERY_LEVEL_HIGH = 3600 /// THERMOSTAT_BATTERY_LEVEL_MEDIUM = 3300 /// THERMOSTAT_BATTERY_LEVEL_LOW = 3000 /// "Below 3000: very low" /// </param> /// <param name="setpoint">Setpoint currently in use by the /// Thermostat.</param> /// <param name="measured">It contains the last measurements of the /// Thermostat</param> /// <param name="setpointHistory">The last 20 setpoints (mode, endtime, /// and timestamp) the thermostats has entered.</param> /// <param name="thermProgramList">List of the weekly heating planning /// used by the thermostat</param> public NAThermostat(string _id = default(string), int?firmware = default(int?), string type = default(string), string moduleName = default(string), int?lastMessage = default(int?), int?rfStatus = default(int?), int?batteryVp = default(int?), NASetpoint setpoint = default(NASetpoint), NASetpoint setpointOrder = default(NASetpoint), int?thermOrientation = default(int?), int?thermRelayCmd = default(int?), int?lastThermSeen = default(int?), NAThermMeasure measured = default(NAThermMeasure), IList <NASetpointLog> setpointHistory = default(IList <NASetpointLog>), IList <NAThermProgram> thermProgramList = default(IList <NAThermProgram>)) { this._id = _id; Firmware = firmware; Type = type; ModuleName = moduleName; LastMessage = lastMessage; RfStatus = rfStatus; BatteryVp = batteryVp; Setpoint = setpoint; SetpointOrder = setpointOrder; ThermOrientation = thermOrientation; ThermRelayCmd = thermRelayCmd; LastThermSeen = lastThermSeen; Measured = measured; SetpointHistory = setpointHistory; ThermProgramList = thermProgramList; CustomInit(); }
/// <summary> /// Initializes a new instance of the NASetpointLog class. /// </summary> public NASetpointLog(NASetpoint setpoint = default(NASetpoint), long?timestamp = default(long?)) { Setpoint = setpoint; Timestamp = timestamp; CustomInit(); }