protected virtual void EditPartParameters(string partName, string newPath, int materialID)
{
foreach (var eachParameter in parameters)
{
try
{
Dimension myDimension = (SolidWorksDocument.Parameter(eachParameter.Key + "@" + partName + ".SLDPRT")) as Dimension;
myDimension.SystemValue = eachParameter.Value / 1000;
}
catch (Exception ex)
{
//System.Windows.Forms.MessageBox.Show(eachParameter.Key + "@" + partName);
MessageObserver.Instance.SetMessage(ex.ToString(), MessageType.Error);
}
}
this.parameters.Clear();
SolidWorksDocument = SolidWorksAdapter.AcativeteDoc(partName);
if (SolidWorksDocument != null)
{
SolidWorksDocument.ForceRebuild3(true);
toSQL.AddCustomProperty("", materialID, SolidWorksAdapter.SldWoksAppExemplare);
SolidWorksDocument.Extension.SaveAs(newPath + ".SLDPRT", (int)swSaveAsVersion_e.swSaveAsCurrentVersion, (int)swSaveAsOptions_e.swSaveAsOptions_Silent
+ (int)swSaveAsOptions_e.swSaveAsOptions_SaveReferenced + (int)swSaveAsOptions_e.swSaveAsOptions_UpdateInactiveViews, null, ref errors, warnings);
InitiatorSaveExeption(errors, warnings, newPath);
SolidWorksAdapter.CloseDocument(SolidWorksDocument);
}
else
{
System.Windows.Forms.MessageBox.Show("Не удалось преобразовать деталь " + partName);
}
SolidWorksAdapter.SldWoksAppExemplare.DocumentVisible(false, 2);
SolidWorksAdapter.SldWoksAppExemplare.DocumentVisible(false, 1);
}
public void BuildMountageFrame(bool cheched, int width, int lenght, int thikness, int FrameType, int offset, int materialID)
{
string assemblyName = "10-4";
string modelMontageFramePath = $@"{base.RootFolder}\{base.SourceFolder}\{assemblyName}.SLDASM";
SolidWorksDocument = SolidWorksAdapter.OpenDocument(modelMontageFramePath, swDocumentTypes_e.swDocASSEMBLY, "");
tbAssemblyNameDataContext bildFrame = new tbAssemblyNameDataContext();
SolidWorksAdapter.ToAssemblyDocument(SolidWorksDocument);
int?ID = 0;
ID = bildFrame.AirVents_AddAssemblyFrame(FrameType, width, lenght, thikness, offset, 0, ref ID);
string assmblName = ID?.ToString();
if (cheched)
{
width = width - 20;
}
tempOffset = offset;
if (offset > (lenght - 125) * 10)
{
offset = (lenght - 250) * 10;
MessageBox.Show("Смещение превышает допустимое значение! Программой установлено - " + (offset / 10));
}
else
{
SetBends = GetSetBends; //получаем значения KFactor, BendRadius из SWPlusBD Materials.BendTable
GetFrameType((MontageFrameType_e)FrameType, lenght, out offset); //определяем по типу рамы, какие балки удалять
SetBends?.Invoke((decimal)thikness, out KFactor, out BendRadius);
if (lenght > 1000)
{
SolidWorksDocument.Extension.SelectByID2("Middle@10-01-01-4-1@10-4", "FTRFOLDER", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditUnsuppress2();
SolidWorksDocument.Extension.SelectByID2("Middle", "FTRFOLDER", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditUnsuppress2();
}
#region Удаление поперечной балки
//Тип рамы 2
if (internalCrossbeam == false)
{
SolidWorksDocument.Extension.SelectByID2("10-03-01-4-1@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-39@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-40@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Washer 6402_gost-23@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Гайка DIN 934-19@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Болт DIN 933-22@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-41@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-42@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Washer 6402_gost-24@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Гайка DIN 934-20@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Болт DIN 933-23@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-43@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-44@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Washer 6402_gost-25@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Гайка DIN 934-21@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Болт DIN 933-24@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-45@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-46@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Washer 6402_gost-26@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Гайка DIN 934-22@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Болт DIN 933-25@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
// Удаление ненужных элементов продольной балки
SolidWorksDocument.Extension.SelectByID2("Вырез-Вытянуть8@10-01-01-4-1@10-4", "BODYFEATURE", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditSuppress2();
}
#endregion
#region Удаление продольной балки
// Погашение внутренней продольной балки
if (internalLongitudinalBeam == false)
{
foreach (var s in new[] { "5", "6", "7", "8" })
{
SolidWorksDocument.Extension.SelectByID2("Болт DIN 933-" + s + "@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
}
foreach (var s in new[] { "6", "7", "8", "9", "37", "38", "39", "40" })
{
SolidWorksDocument.Extension.SelectByID2("Washer 6402_gost-" + s + "@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
}
foreach (var s in new[] { "17", "18", "19", "20", "21", "22", "23", "24", "57", "58", "59", "60" })
{
SolidWorksDocument.Extension.SelectByID2("Шайба DIN 125-" + s + "@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
}
SolidWorksDocument.Extension.SelectByID2("10-04-4-2@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
//// Удаление ненужных элементов поперечной балки
SolidWorksDocument.Extension.SelectByID2("Регулируемая ножка-10@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Регулируемая ножка-11@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditDelete();
SolidWorksDocument.Extension.SelectByID2("Регулируемая ножка-002@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditDelete();
foreach (var s in new[] { "10", "11", "12", "13", "40", "41", "42", "43" })
{
SolidWorksDocument.Extension.SelectByID2("Гайка DIN 934-" + s + "@10-4", "COMPONENT", 0, 0, 0, true, 0, null, 0);
SolidWorksDocument.EditDelete();
}
int deleteOption = (int)swDeleteSelectionOptions_e.swDelete_Absorbed + (int)swDeleteSelectionOptions_e.swDelete_Children;
SolidWorksDocument.Extension.SelectByID2("Вырез-Вытянуть5@10-03-01-4@10-4", "BODYFEATURE", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.Extension.DeleteSelection2(deleteOption);
SolidWorksDocument.Extension.SelectByID2("Вырез-Вытянуть4@10-03-01-4@10-4", "BODYFEATURE", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.Extension.DeleteSelection2(deleteOption);
}
else
{
//Продольные балки (Длина установки)
ID = 0;
ID = bildFrame.AirVents_AddAssemblyFrame(FrameType, width, 0, thikness, 0, 4, ref ID);
SolidWorksDocument.Extension.SelectByID2("10-04-4-2@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditUnsuppress2();
base.parameters.Add("D1@Эскиз1", lenght - 140);
base.parameters.Add("D1@Листовой металл", (double)BendRadius);
base.parameters.Add("D2@Листовой металл", (double)KFactor * 1000);
base.parameters.Add("Толщина@Листовой металл", thikness);
EditPartParameters("10-04-4", base.NewPartPath + @"\10-" + ID, materialID);
}
#endregion
}
#region Изменение параметров
if (internalCrossbeam == true)
{
ID = 0;
ID = bildFrame.AirVents_AddAssemblyFrame(FrameType, width, 0, thikness, offset, 2, ref ID);
bildFrame.SubmitChanges();
SolidWorksDocument = SolidWorksAdapter.AcativeteDoc("10-01-01-4");
SolidWorksDocument.Extension.SaveAs(base.NewPartPath + @"\10-" + ID + ".SLDPRT", (int)swSaveAsVersion_e.swSaveAsCurrentVersion, (int)swSaveAsOptions_e.swSaveAsOptions_Silent
+ (int)swSaveAsOptions_e.swSaveAsOptions_Copy, null, ref errors, warnings);
SolidWorksAdapter.CloseDocument(SolidWorksDocument);
SolidWorksDocument = SolidWorksAdapter.AcativeteDoc("10-4");
SolidWorksDocument.Extension.SelectByID2("10-01-01-4-2@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
AssemblyDocument.ReplaceComponents(base.NewPartPath + @"\10-" + ID + ".SLDPRT", "", false, true);
base.parameters.Add("D1@Эскиз1", lenght);
base.parameters.Add("D3@Эскиз25", lenght - offset);
base.parameters.Add("D1@Листовой металл", (double)BendRadius);
base.parameters.Add("D2@Листовой металл", (double)KFactor * 1000);
base.parameters.Add("Толщина@Листовой металл", thikness);
EditPartParameters(@"10-" + ID, base.NewPartPath + @"\10 -" + ID, materialID);
}
//Продольные балки (Длина установки)
ID = 0;
ID = bildFrame.AirVents_AddAssemblyFrame(FrameType, lenght, 0, thikness, offset, 1, ref ID);
bildFrame.SubmitChanges();
base.parameters.Add("D1@Эскиз1", lenght);
base.parameters.Add("D3@Эскиз25", offset);
base.parameters.Add("D1@Листовой металл", (double)BendRadius);
base.parameters.Add("D2@Листовой металл", (double)KFactor * 1000);
base.parameters.Add("Толщина@Листовой металл", thikness);
EditPartParameters("10-01-01-4", base.NewPartPath + @"\10-" + ID, materialID);
// Поперечная балка (Ширина установки)
ID = 0;
ID = bildFrame.AirVents_AddAssemblyFrame(FrameType, Convert.ToInt32(width - 0.12), 0, thikness, 0, 3, ref ID);
bildFrame.SubmitChanges();
SolidWorksDocument = SolidWorksAdapter.AcativeteDoc("10-4");
SolidWorksDocument.Extension.SelectByID2("10-03-01-4-1@10-4", "COMPONENT", 0, 0, 0, false, 0, null, 0);
SolidWorksDocument.EditUnsuppress2();
base.parameters.Add("D2@Эскиз1", width - 0.12);
base.parameters.Add("D1@Листовой металл", (double)BendRadius);
base.parameters.Add("D2@Листовой металл", (double)KFactor * 1000);
base.parameters.Add("Толщина@Листовой металл", thikness);
EditPartParameters("10-03-01-4", base.NewPartPath + @"\10-" + ID, materialID);
#endregion
SaveDoc(assmblName);
}