public LocalRoadModel(CarTimestamp timestamp, double modelProbability, LocalLaneModel centerLane, LocalLaneModel leftLane, LocalLaneModel rightLane)
{
this.timestamp = timestamp;
this.modelProbability = modelProbability;
this.centerLane = centerLane;
this.leftLane = leftLane;
this.rightLane = rightLane;
}
public LocalRoadModel(CarTimestamp timestamp, double modelProbability, LocalLaneModel centerLane, LocalLaneModel leftLane, LocalLaneModel rightLane)
{
this.timestamp = timestamp;
this.modelProbability = modelProbability;
this.centerLane = centerLane;
this.leftLane = leftLane;
this.rightLane = rightLane;
}
private LaneModelTestResult TestLane(LinePath rndfPath, CarTimestamp rndfPathTimestamp, LocalLaneModel laneModel)
{
// construct the result object to hold stuff
LaneModelTestResult result = new LaneModelTestResult();
// project the lane model's path into the rndf path's timestamp
RelativeTransform relTransform = Services.RelativePose.GetTransform(localRoadModel.Timestamp, rndfPathTimestamp);
LinePath laneModelPath = laneModel.LanePath.Transform(relTransform);
// get the zero point of the lane model path
LinePath.PointOnPath laneZeroPoint = laneModelPath.ZeroPoint;
// get the first waypoint on the RNDF path
LinePath.PointOnPath rndfZeroPoint = rndfPath.ZeroPoint;
// get the heading of the rndf path at its zero point and the heading of the lane model at
// the rndf's zero point
LinePath.PointOnPath laneStartPoint = laneModelPath.GetClosestPoint(rndfZeroPoint.Location);
Coordinates laneModelHeading = laneModelPath.GetSegment(laneStartPoint.Index).UnitVector;
Coordinates rndfHeading = rndfPath.GetSegment(rndfZeroPoint.Index).UnitVector;
double angle = Math.Acos(laneModelHeading.Dot(rndfHeading));
// check if the angle is within limits for comparing offset
if (angle < 30*Math.PI/180.0) {
// get the deviation between lane zero point and rndf zero point
result.rndf_deviation = rndfZeroPoint.Location.DistanceTo(laneZeroPoint.Location);
}
// now start check for how many waypoints are accepted
for (int i = rndfZeroPoint.Index + 1; i < rndfPath.Count; i++) {
// check the distance along the rndf path
double rndfDistAlong = rndfPath.DistanceBetween(rndfZeroPoint, rndfPath.GetPointOnPath(i));
// break out if we're too far along the rndf
if (rndfDistAlong > 50) {
break;
}
// get the waypoint
Coordinates waypoint = rndfPath[i];
// project on to lane path
LinePath.PointOnPath laneWaypoint = laneModelPath.GetClosestPoint(waypoint);
// check if we're too far along the lane path
double distAlong = laneModelPath.DistanceBetween(laneZeroPoint, laneWaypoint);
if (distAlong > lane_model_max_dist || distAlong < 0) {
break;
}
// check if the deviation
double dist = waypoint.DistanceTo(laneWaypoint.Location);
// increment appropriate counts
if (dist < lane_deviation_reject_threshold) {
result.forward_match_count++;
}
else {
result.forward_rejection_count++;
}
}
// return the result
return result;
}
private ILaneModel GetLaneModel(LocalLaneModel laneModel, LinePath rndfPath, double rndfPathWidth, CarTimestamp rndfPathTimestamp)
{
// check the lane model probability
if (laneModel.Probability < lane_probability_reject_threshold) {
// we're rejecting this, just return a path lane model
return new PathLaneModel(rndfPathTimestamp, rndfPath, rndfPathWidth);
}
// project the lane model's path into the rndf path's timestamp
RelativeTransform relTransform = Services.RelativePose.GetTransform(localRoadModel.Timestamp, rndfPathTimestamp);
LinePath laneModelPath = laneModel.LanePath.Transform(relTransform);
// iterate through the waypoints in the RNDF path and project onto the lane model
// the first one that is over the threshold, we consider the waypoint before as a potential ending point
LinePath.PointOnPath laneModelDeviationEndPoint = new LinePath.PointOnPath();
// flag indicating if any of the waypoint tests failed because of the devation was too high
bool anyDeviationTooHigh = false;
// number of waypoints accepted
int numWaypointsAccepted = 0;
// get the vehicle's position on the rndf path
LinePath.PointOnPath rndfZeroPoint = rndfPath.ZeroPoint;
// get the vehicle's position on the lane model
LinePath.PointOnPath laneModelZeroPoint = laneModelPath.ZeroPoint;
// get the last point we want to consider on the lane model
LinePath.PointOnPath laneModelFarthestPoint = laneModelPath.AdvancePoint(laneModelZeroPoint, lane_model_max_dist);
// start walking forward through the waypoints on the rndf path
// this loop will implicitly exit when we're past the end of the lane model as the waypoints
// will stop being close to the lane model (GetClosestPoint returns the end point if we're past the
// end of the path)
for (int i = rndfZeroPoint.Index+1; i < rndfPath.Count; i++) {
// get the waypoint
Coordinates rndfWaypoint = rndfPath[i];
// get the closest point on the lane model
LinePath.PointOnPath laneModelClosestPoint = laneModelPath.GetClosestPoint(rndfWaypoint);
// compute the distance between the two
double deviation = rndfWaypoint.DistanceTo(laneModelClosestPoint.Location);
// if this is above the deviation threshold, leave the loop
if (deviation > lane_deviation_reject_threshold || laneModelClosestPoint > laneModelFarthestPoint) {
// if we're at the end of the lane model path, we don't want to consider this a rejection
if (laneModelClosestPoint < laneModelFarthestPoint) {
// mark that at least on deviation was too high
anyDeviationTooHigh = true;
}
break;
}
// increment the number of waypoint accepted
numWaypointsAccepted++;
// update the end point of where we're valid as the local road model was OK up to this point
laneModelDeviationEndPoint = laneModelClosestPoint;
}
// go through and figure out how far out the variance is within tolerance
LinePath.PointOnPath laneModelVarianceEndPoint = new LinePath.PointOnPath();
// walk forward from this point until the end of the lane mode path
for (int i = laneModelZeroPoint.Index+1; i < laneModelPath.Count; i++) {
// check if we're within the variance toleration
if (laneModel.LaneYVariance[i] <= y_var_reject_threshold) {
// we are, update the point on path
laneModelVarianceEndPoint = laneModelPath.GetPointOnPath(i);
}
else {
// we are out of tolerance, break out of the loop
break;
}
}
// now figure out everything out
// determine waypoint rejection status
WaypointRejectionResult waypointRejectionResult;
if (laneModelDeviationEndPoint.Valid) {
// if the point is valid, that we had at least one waypoint that was ok
// check if any waypoints were rejected
if (anyDeviationTooHigh) {
// some waypoint was ok, so we know that at least one waypoint was accepted
waypointRejectionResult = WaypointRejectionResult.SomeWaypointsAccepted;
}
else {
// no waypoint triggered a rejection, but at least one was good
waypointRejectionResult = WaypointRejectionResult.AllWaypointsAccepted;
}
}
else {
// the point is not valid, so we either had no waypoints or we had all rejections
if (anyDeviationTooHigh) {
// the first waypoint was rejected, so all are rejected
waypointRejectionResult = WaypointRejectionResult.AllWaypointsRejected;
}
else {
// the first waypoint (if any) was past the end of the lane model
waypointRejectionResult = WaypointRejectionResult.NoWaypoints;
}
}
// criteria for determining if this path is valid:
// - if some or all waypoints were accepted, than this is probably a good path
// - if some of the waypoints were accepted, we go no farther than the last waypoint that was accepted
// - if there were no waypoints, this is a potentially dangerous situation since we can't reject
// or confirm the local road model. for now, we'll assume that it is correct but this may need to change
// if we start handling intersections in this framework
// - if all waypoints were rejected, than we don't use the local road model
// - go no farther than the laneModelVarianceEndPoint, which is the last point where the y-variance of
// the lane model was in tolerance
// now build out the lane model
ILaneModel finalLaneModel;
// check if we rejected all waypoints or no lane model points satisified the variance threshold
if (waypointRejectionResult == WaypointRejectionResult.AllWaypointsRejected || !laneModelVarianceEndPoint.Valid) {
// want to just use the path lane model
finalLaneModel = new PathLaneModel(rndfPathTimestamp, rndfPath, rndfPathWidth);
}
else {
// we'll use the lane model
// need to build up the center line as well as left and right bounds
// to build up the center line, use the lane model as far as we feel comfortable (limited by either variance
// or by rejections) and then use the rndf lane after that.
LinePath centerLine = new LinePath();
// figure out the max distance
// if there were no waypoints, set the laneModelDeviationEndPoint to the end of the lane model
if (waypointRejectionResult == WaypointRejectionResult.NoWaypoints) {
laneModelDeviationEndPoint = laneModelFarthestPoint;
}
// figure out the closer of the end points
LinePath.PointOnPath laneModelEndPoint = (laneModelDeviationEndPoint < laneModelVarianceEndPoint) ? laneModelDeviationEndPoint : laneModelVarianceEndPoint;
bool endAtWaypoint = laneModelEndPoint == laneModelDeviationEndPoint;
// add the lane model to the center line
centerLine.AddRange(laneModelPath.GetSubpathEnumerator(laneModelZeroPoint, laneModelEndPoint));
// create a list to hold the width expansion values
List<double> widthValue = new List<double>();
// make the width expansion values the width of the path plus the 1-sigma values
for (int i = laneModelZeroPoint.Index; i < laneModelZeroPoint.Index+centerLine.Count; i++) {
widthValue.Add(laneModel.Width/2.0 + Math.Sqrt(laneModel.LaneYVariance[i]));
}
// now figure out how to add the rndf path
// get the projection of the lane model end point on the rndf path
LinePath.PointOnPath rndfPathStartPoint = rndfPath.GetClosestPoint(laneModelEndPoint.Location);
// if the closest point is past the end of rndf path, then we don't want to tack anything on
if (rndfPathStartPoint != rndfPath.EndPoint) {
// get the last segment of the new center line
Coordinates centerLineEndSegmentVec = centerLine.EndSegment.UnitVector;
// get the last point of the new center line
Coordinates laneModelEndLoc = laneModelEndPoint.Location;
// now figure out the distance to the next waypoint
LinePath.PointOnPath rndfNextPoint = new LinePath.PointOnPath();
// figure out if we're ending at a waypoint or not
if (endAtWaypoint) {
rndfNextPoint = rndfPath.GetPointOnPath(rndfPathStartPoint.Index+1);
// if the distance from the start point to the next point is less than rndf_dist_min, then
// use the waypont after
double dist = rndfPath.DistanceBetween(rndfPathStartPoint, rndfNextPoint);
if (dist < rndf_dist_min) {
if (rndfPathStartPoint.Index < rndfPath.Count-2) {
rndfNextPoint = rndfPath.GetPointOnPath(rndfPathStartPoint.Index + 2);
}
else if (rndfPath.DistanceBetween(rndfPathStartPoint, rndfPath.EndPoint) < rndf_dist_min) {
rndfNextPoint = LinePath.PointOnPath.Invalid;
}
else {
rndfNextPoint = rndfPath.AdvancePoint(rndfPathStartPoint, rndf_dist_min*2);
}
}
}
else {
// track the last angle we had
double lastAngle = double.NaN;
// walk down the rndf path until we find a valid point
for (double dist = rndf_dist_min; dist <= rndf_dist_max; dist += rndf_dist_step) {
// advance from the start point by dist
double distTemp = dist;
rndfNextPoint = rndfPath.AdvancePoint(rndfPathStartPoint, ref distTemp);
// if the distTemp is > 0, then we're past the end of the path
if (distTemp > 0) {
// if we're immediately past the end, we don't want to tack anything on
if (dist == rndf_dist_min) {
rndfNextPoint = LinePath.PointOnPath.Invalid;
}
break;
}
// check the angle made by the last segment of center line and the segment
// formed between the end point of the center line and this new point
double angle = Math.Acos(centerLineEndSegmentVec.Dot((rndfNextPoint.Location-laneModelEndLoc).Normalize()));
// check if the angle satisfies the threshold or we're increasing the angle
if (Math.Abs(angle) < rndf_angle_threshold || (!double.IsNaN(lastAngle) && angle > lastAngle)) {
// break out of the loop, we're done searching
break;
}
lastAngle = angle;
}
}
// tack on the rndf starting at next point going to the end
if (rndfNextPoint.Valid) {
LinePath subPath = rndfPath.SubPath(rndfNextPoint, rndfPath.EndPoint);
centerLine.AddRange(subPath);
// insert the lane model end point into the sub path
subPath.Insert(0, laneModelEndLoc);
// get the angles
List<Pair<int, double>> angles = subPath.GetIntersectionAngles(0, subPath.Count-1);
// add the width of the path inflated by the angles
for (int i = 0; i < angles.Count; i++) {
// calculate the width expansion factor
// 90 deg, 3x width
// 45 deg, 1.5x width
// 0 deg, 1x width
double widthFactor = Math.Pow(angles[i].Right/(Math.PI/2.0), 2)*2 + 1;
// add the width value
widthValue.Add(widthFactor*laneModel.Width/2);
}
// add the final width
widthValue.Add(laneModel.Width/2);
}
// set the rndf path start point to be the point we used
rndfPathStartPoint = rndfNextPoint;
}
// for now, calculate the left and right bounds the same way we do for the path lane model
// TODO: figure out if we want to do this more intelligently using knowledge of the lane model uncertainty
LinePath leftBound = centerLine.ShiftLateral(widthValue.ToArray());
// get the next shifts
for (int i = 0; i < widthValue.Count; i++) { widthValue[i] = -widthValue[i]; }
LinePath rightBound = centerLine.ShiftLateral(widthValue.ToArray());
// build the final lane model
finalLaneModel = new CombinedLaneModel(centerLine, leftBound, rightBound, laneModel.Width, rndfPathTimestamp);
}
SendLaneModelToUI(finalLaneModel, rndfPathTimestamp);
// output the fit result
return finalLaneModel;
}
private bool CheckGeneralShape(LinePath rndfPath, CarTimestamp rndfPathTimestamp, LocalLaneModel centerLaneModel)
{
// bad newz bears
if (centerLaneModel.LanePath == null || centerLaneModel.LanePath.Count < 2) {
return false;
}
// project the lane model's path into the rndf path's timestamp
RelativeTransform relTransform = Services.RelativePose.GetTransform(localRoadModel.Timestamp, rndfPathTimestamp);
LinePath laneModelPath = centerLaneModel.LanePath.Transform(relTransform);
// get the zero point of the lane model path
LinePath.PointOnPath laneZeroPoint = laneModelPath.ZeroPoint;
// get the first waypoint on the RNDF path
LinePath.PointOnPath rndfZeroPoint = rndfPath.ZeroPoint;
Coordinates firstWaypoint = rndfPath[rndfZeroPoint.Index+1];
// get the projection of the first waypoint onto the lane path
LinePath.PointOnPath laneFirstWaypoint = laneModelPath.GetClosestPoint(firstWaypoint);
// get the offset vector
Coordinates offsetVector = laneFirstWaypoint.Location - firstWaypoint;
// start iterating through the waypoints forward and project them onto the rndf path
for (int i = rndfZeroPoint.Index+1; i < rndfPath.Count; i++) {
// get the waypoint
Coordinates waypoint = rndfPath[i];
// adjust by the first waypoint offset
waypoint += offsetVector;
// project onto the lane model
LinePath.PointOnPath laneWaypoint = laneModelPath.GetClosestPoint(waypoint);
// check the distance from the zero point on the lane model
if (laneModelPath.DistanceBetween(laneZeroPoint, laneWaypoint) > road_model_max_dist) {
break;
}
// check the devation from the rndf
double deviation = waypoint.DistanceTo(laneWaypoint.Location);
// if the deviation is over some threshold, then we reject the model
if (deviation > road_deviation_reject_threshold) {
return false;
}
}
// we got this far, so this stuff is OK
return true;
}
