//------------------------------------------//
public clSliceData getSliceData(int ObjectIndex, int LayerIndex, float jobLayerThickness)
{
clSliceData sd = new clSliceData();
int n = 0;
if (ObjectIndex != 0)
{
return(sd);
}
float scaleFactor = m_FileHead.scaleFactor;
//m_error.addInfo(System.IO.Path.GetFileName( m_filename) +" : factor: " + scaleFactor + "; ");
int convertedLayerindex = LayerIndex - (int)(m_IndexTable[0].layerPos / jobLayerThickness); // Min z
if ((convertedLayerindex >= 0) && (convertedLayerindex < m_IndexTable_count))
{
setOffset(m_IndexTable[convertedLayerindex].FileOffset);
int OType = 0;
while (OType != 2)
{
//- Befehl/Operator Byte
OType = readIntBE(1);
switch (OType)
{
case 1:
//- ersten 2 Byte sind ca. die Höhe??!!!
readByte(11); //- Header überspringen
//- Header... lesen???!!!
break;
case 2:
//- Ende
break;
case 3:
//Command : start polyline
//Syntax : $$POLYLINE/id,dir,n,p1x,p1y,...pnx,pny
//Parameters:
//
// id : INTEGER
// dir,n : INTEGER
// p1x..pny : REAL
//
//
//id : identifier to allow more than one model information in one file.
//id refers to the parameter id of command $$LABEL (HEADER-section).
//dir : Orientation of the line when viewing in the negative z-direction
//0 : clockwise (internal)
//1 : counter-clockwise (external)
//2 : open line (no solid)
//n : number of points
//p1x..pny : coordinates of the points 1..n
if (readIntBE(1) != 0) //- vielleicht "dir"?
{
m_error.addWarning("unbekanntes Byte [dir?] @ " + m_offset);
}
n = readIntBE(2);
if (n > 0)
{
//int n2 = n*2; //- x+y
float[,] points = new float[n, 2];
//- Punkte lesen
for (int i = 0; i < n; i++)
{
//- Punkt lesen und mit internem Faktor skalieren
points[i, 0] = scaleFactor * readIntBE(2);
points[i, 1] = scaleFactor * readIntBE(2);
}
sd.addPolygon(points, n);
}
break;
case 4:
//- support
//m_error.addWarning("Support is not supported!");
//Command : start hatches
//Syntax : $$HATCHES/id,n,p1sx,p1sy,p1ex,p1ey,...pnex,pney
//Parameters:
//
// id : INTEGER
// n : INTEGER
// p1sx..pney : REAL
//
//id : identifier to allow more than one model information in one file.
//id refers to the parameter id of command $$LABEL (HEADER-section).
//n : number of hatches (n*4 =number of coordinates)
//p1sx..pney : coordinates of the hatches 1..n
//4 parameters for every hatch (startx,starty,endx,endy)
//- Keine Ahnung
if (readIntBE(1) != 0)
{
m_error.addWarning("unbekanntes Byte @ " + m_offset);
}
n = readIntBE(2);
if (n > 0)
{
//- hier gibt es 2 Punkt pro Linie
int m = n * 2;
float[,] points = new float[m, 2];
//- Punkte lesen: es werden 2*n Punkte eingelesen da jede Linie einen Start und ein Ende-Punkt hat
for (int i = 0; i < m; i++)
{
points[i, 0] = scaleFactor * readIntBE(2); //- start/ende-x
points[i, 1] = scaleFactor * readIntBE(2); //- start/ende-y
}
sd.addHatch(points, m);
}
break;
default:
m_error.addWarning("Data-Stream-Error??? Unknow Data Type: " + OType + " @ " + m_offset);
break;
}
}
}
return(sd);
}
//------------------------------------------//
public clSliceData getSliceData(int ObjectIndex, int LayerIndex, float jobLayerThickness)
{
clSliceData retSlice = new clSliceData();
if (ObjectIndex != 0)
{
return(retSlice);
}
if ((LayerIndex < 0) || (LayerIndex >= m_IndexTable_count))
{
return(retSlice);
}
setOffset(m_IndexTable[LayerIndex].FileOffset);
float scale = m_FileHead.unit; //- Faktor in [mm]
for (int i = 0; i < m_IndexTable[LayerIndex].polyCount; i++)
{
int cmd = readIntBE(2);
int pointCount = 0;
float [,] pointBuffer;
switch (cmd)
{
case 129: //- Start PolyLine short
readIntBE(2); //- id
readIntBE(2); //- dir
pointCount = readIntBE(2); //- number of points
pointBuffer = new float[pointCount, 2];
for (int p = 0; p < pointCount; p++)
{
pointBuffer[p, 0] = scale * readIntBE(2);
pointBuffer[p, 1] = scale * readIntBE(2);
}
retSlice.addPolygon(pointBuffer, pointCount);
break;
case 130: //- Start PolyLine long
readIntBE(4); //- id
readIntBE(4); //- dir
pointCount = readIntBE(4); //- number of points
pointBuffer = new float[pointCount, 2];
for (int p = 0; p < pointCount; p++)
{
pointBuffer[p, 0] = readRealBE(4) * scale;
pointBuffer[p, 1] = readRealBE(4) * scale;
}
retSlice.addPolygon(pointBuffer, pointCount);
break;
default:
m_error.addError("indexFileBinary() : data out of sync. Unknown command: " + cmd + " at pos: " + m_offset);
break;
}
}
return(retSlice);
}
