public static void Main()
{
// get available ports
var serialPorts = SerialDevice.GetDeviceSelector();
Console.WriteLine("available serial ports: " + serialPorts);
// COM6 in STM32F769IDiscovery board (Tx, Rx pins exposed in Arduino header CN13: TX->D1, RX->D0)
// open COM
_serialDevice = SerialDevice.FromId("COM6");
// set parameters
_serialDevice.BaudRate = 38400;
_serialDevice.Parity = SerialParity.None;
_serialDevice.StopBits = SerialStopBitCount.One;
_serialDevice.Handshake = SerialHandshake.None;
_serialDevice.DataBits = 8;
// uncomment the scenario to test (!!note that none of these returns!!)
// uncomment the following call to transmit data
Scenario2_StreamWrite.Execute(ref _serialDevice);
// uncomment the following call to read data using a stream reader
//Scenario3_StreamRead.Execute(ref _serialDevice);
// uncomment the following call to wait for a data received event
//Scenario4_DataReceivedEvent.Execute(ref _serialDevice);
Thread.Sleep(Timeout.Infinite);
}
public static void Main()
{
// get available ports
var serialPorts = SerialDevice.GetDeviceSelector();
Console.WriteLine("available serial ports: " + serialPorts);
// COM6 in STM32F769IDiscovery board (Tx, Rx pins exposed in Arduino header CN13: TX->D1, RX->D0)
// open COM
_serialDevice = SerialDevice.FromId("COM1");
// set parameters
_serialDevice.BaudRate = 115200;
_serialDevice.Parity = SerialParity.None;
_serialDevice.StopBits = SerialStopBitCount.One;
_serialDevice.Handshake = SerialHandshake.None;
_serialDevice.DataBits = 8;
for (; ;)
{
Scenario2_StreamWrite.Execute(ref _serialDevice);
/*Scenario3_StreamRead.Execute(ref _serialDevice);*/
Thread.Sleep(20);
}
}
public static void Main()
{
// get available ports
var serialPorts = SerialDevice.GetDeviceSelector();
Console.WriteLine("available serial ports: " + serialPorts);
///////////////////////////////////////////////////////////////////////////////////////////////////
// COM6 in STM32F769IDiscovery board (Tx, Rx pins exposed in Arduino header CN13: TX->D1, RX->D0)
// open COM6
//_serialDevice = SerialDevice.FromId("COM6");
////////////////////////////////////////////////////////////////////////////////////////////////////
// COM2 in ESP32-WROVER-KIT mapped to free GPIO pins
// mind to NOT USE pins shared with other devices, like serial flash and PSRAM
// also it's MANDATORY to set pin funcion to the appropriate COM before instanciating it
// set GPIO functions for COM2 (this is UART1 on ESP32)
#if BUIID_FOR_ESP32
//Configuration.SetPinFunction(Gpio.IO04, DeviceFunction.COM2_TX);
//Configuration.SetPinFunction(Gpio.IO05, DeviceFunction.COM2_RX);
#endif
// open COM2
_serialDevice = SerialDevice.FromId("COM2");
// set parameters
_serialDevice.BaudRate = 9600;
_serialDevice.Parity = SerialParity.None;
_serialDevice.StopBits = SerialStopBitCount.One;
_serialDevice.Handshake = SerialHandshake.None;
_serialDevice.DataBits = 8;
// uncomment the scenario to test (!!note that none of these returns!!)
// uncomment the following call to transmit data
Scenario2_StreamWrite.Execute(ref _serialDevice);
// uncomment the following call to read data using a stream reader
Scenario3_StreamRead.Execute(ref _serialDevice);
// uncomment the following call to wait for a data received event
//Scenario4_DataReceivedEvent.Execute(ref _serialDevice);
Thread.Sleep(Timeout.Infinite);
}