/// <summary>
/// Constructor of the Control System Class. Make sure the constructor always exists.
/// If it doesn't exit, the code will not run on your 3-Series processor.
/// </summary>
public ControlSystem() : base()
{
// subscribe to control system events
CrestronEnvironment.SystemEventHandler += new SystemEventHandler(CrestronEnvironment_SystemEventHandler);
CrestronEnvironment.ProgramStatusEventHandler += new ProgramStatusEventHandler(CrestronEnvironment_ProgramStatusEventHandler);
CrestronEnvironment.EthernetEventHandler += new EthernetEventHandler(CrestronEnvironment_EthernetEventHandler);
// Set the number of threads which you want to use in your program - At this point the threads cannot be created but we should
// define the max number of threads which we will use in the system.
// the right number depends on your project; do not make this number unnecessarily large
Thread.MaxNumberOfUserThreads = 20;
if (this.SupportsComPort)
{
MyCOMPort = this.ComPorts[1];
MyCOMPort.SerialDataReceived += new ComPortDataReceivedEvent(myComPort_SerialDataReceived);
if (MyCOMPort.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("COM Port couldn't be registered. Cause: {0}", MyCOMPort.DeviceRegistrationFailureReason);
}
if (MyCOMPort.Registered)
{
MyCOMPort.SetComPortSpec(ComPort.eComBaudRates.ComspecBaudRate9600,
ComPort.eComDataBits.ComspecDataBits8,
ComPort.eComParityType.ComspecParityNone,
ComPort.eComStopBits.ComspecStopBits1,
ComPort.eComProtocolType.ComspecProtocolRS232,
ComPort.eComHardwareHandshakeType.ComspecHardwareHandshakeNone,
ComPort.eComSoftwareHandshakeType.ComspecSoftwareHandshakeNone,
false);
}
}
// ensure this processor has ethernet then setup the EISC
if (this.SupportsEthernet)
{
myEISC = new EthernetIntersystemCommunications(eISCIPID, eISCIP, this);
if (myEISC.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error(">>> The EISC was not registered: {0}", myEISC.RegistrationFailureReason);
}
else
{
// Device has been registered. Now register for the event handlers
myEISC.OnlineStatusChange += new OnlineStatusChangeEventHandler(myEISC_OnlineStatusChange);
myEISC.SigChange += new SigEventHandler(myEISC_SigChange);
ErrorLog.Notice(">>> The EISC has been registered successfully");
}
}
else
{
ErrorLog.Error(">>> This processor does not support ethernet, so this program will not run");
}
}
public EthernetIntersystemCommunications Create()
{
var eisc = new EthernetIntersystemCommunications(0x09, "10.51.10.112", ProAvControlSystem.ControlSystem);
eisc.Register();
eisc.OnlineStatusChange += EiscOnOnlineStatusChange;
ConsoleCommands.Create(x_ => {
uint join;
x_.TryParseToUint(out join);
eisc.BooleanInput[join].Pulse(1000);
}, "testbool", "testbool joinnumber");
ConsoleCommands.Create(x_ => {
uint join;
x_.TryParseToUint(out join);
eisc.StringInput[x_].StringValue = DateTime.Now.ToLongTimeString();
}, "testserial", "testserial joinnumber");
return(eisc);
}
/// <summary>
/// ControlSystem Constructor. Starting point for the SIMPL#Pro program.
/// Use the constructor to:
/// * Initialize the maximum number of threads (max = 400)
/// * Register devices
/// * Register event handlers
/// * Add Console Commands
///
/// Please be aware that the constructor needs to exit quickly; if it doesn't
/// exit in time, the SIMPL#Pro program will exit.
///
/// You cannot send / receive data in the constructor
/// </summary>
public ControlSystem()
: base()
{
try
{
Thread.MaxNumberOfUserThreads = 20;
//Subscribe to the controller events (System, Program, and Ethernet)
CrestronEnvironment.SystemEventHandler += new SystemEventHandler(ControlSystem_ControllerSystemEventHandler);
CrestronEnvironment.ProgramStatusEventHandler += new ProgramStatusEventHandler(ControlSystem_ControllerProgramEventHandler);
CrestronEnvironment.EthernetEventHandler += new EthernetEventHandler(ControlSystem_ControllerEthernetEventHandler);
// Connect to EIC to receive signals from SIMPL Program
EthernetIntersystemCommunications eic = new EthernetIntersystemCommunications(0xfe, "127.0.0.2", this);
// Add the signal handler
eic.SigChange += new SigEventHandler(EICSignalHandler);
eic.Register();
}
catch (Exception e)
{
ErrorLog.Error("Error in the constructor: {0}", e.Message);
}
}
public ControlSystem()
: base()
{
try {
Thread.MaxNumberOfUserThreads = 20;
// Register the Amp, the Zones and the EISC
// Amp Construction
amp197 = new C2nAmp6X100(0x04, this);
amp197.Description = "~~ P-197 Amplifier ~~";
amp197.RoomChangeEvent += new RoomEventHandler(amp197_RoomChangeEvent);
amp197.Register();
// Zones Definition
p197zones = new Room[7];
p197zones[0] = amp197.Room[1]; // Master Bed
p197zones[1] = amp197.Room[2]; // Master Ensuite
p197zones[2] = amp197.Room[3]; // Bedroom 2
p197zones[3] = amp197.Room[4]; // Ensuite 2
p197zones[4] = amp197.Room[5]; // Bedroom 3
p197zones[5] = amp197.Room[7]; // Kitchen
p197zones[6] = amp197.Room[8]; // Dining
amp197.Room[1].Name.StringValue = "Master Bed";
amp197.Room[2].Name.StringValue = "Master Ensuite";
amp197.Room[3].Name.StringValue = "Bedroom 2";
amp197.Room[4].Name.StringValue = "Ensuite 2";
amp197.Room[5].Name.StringValue = "Bedroom 3";
amp197.Room[7].Name.StringValue = "Kitchen";
amp197.Room[8].Name.StringValue = "Dining";
// Sources Array
sources = new ushort[7];
sources[0] = 1;
sources[1] = 1;
sources[2] = 2;
sources[3] = 2;
sources[4] = 3;
sources[5] = 4;
sources[6] = 4;
// Initialize Every Zone Volume to a non eardrum-fatal level
for (uint i = 0; i <= 6; i++)
{
p197zones[i].Volume.UShortValue = p197zones[i].VolumeFeedback.UShortValue;
}
// EISC Construction
ampeisc = new EthernetIntersystemCommunications(0xf0, "127.0.0.2", this);
ampeisc.Description = "~~ Amplifier EISC ~~";
ampeisc.SigChange += new SigEventHandler(ampeisc_SigChange);
ampeisc.Register();
// Cross Routing
screens = new uint[6];
for (uint i = 0; i <= 5; i++)
{
screens[i] = 33;
}
//Subscribe to the controller events (System, Program, and Ethernet)
CrestronEnvironment.SystemEventHandler += new SystemEventHandler(ControlSystem_ControllerSystemEventHandler);
CrestronEnvironment.ProgramStatusEventHandler += new ProgramStatusEventHandler(ControlSystem_ControllerProgramEventHandler);
CrestronEnvironment.EthernetEventHandler += new EthernetEventHandler(ControlSystem_ControllerEthernetEventHandler);
}
catch (Exception e) {
ErrorLog.Error("Error in the constructor: {0}", e.Message);
}
}
/// <summary>
/// Constructor of the Control System Class. Make sure the constructor always exists.
/// If it doesn't exit, the code will not run on your 3-Series processor.
/// </summary>
public ControlSystem() : base()
{
// subscribe to control system events
CrestronEnvironment.SystemEventHandler += new SystemEventHandler(CrestronEnvironment_SystemEventHandler);
CrestronEnvironment.ProgramStatusEventHandler += new ProgramStatusEventHandler(CrestronEnvironment_ProgramStatusEventHandler);
CrestronEnvironment.EthernetEventHandler += new EthernetEventHandler(CrestronEnvironment_EthernetEventHandler);
// Set the number of threads which you want to use in your program - At this point the threads cannot be created but we should
// define the max number of threads which we will use in the system.
// the right number depends on your project; do not make this number unnecessarily large
Thread.MaxNumberOfUserThreads = 20;
if (this.SupportsComPort)
{
MyCOMPort = this.ComPorts[1];
MyCOMPort.SerialDataReceived += new ComPortDataReceivedEvent(myComPort_SerialDataReceived);
if (MyCOMPort.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
ErrorLog.Error("COM Port couldn't be registered. Cause: {0}", MyCOMPort.DeviceRegistrationFailureReason);
if (MyCOMPort.Registered)
MyCOMPort.SetComPortSpec(ComPort.eComBaudRates.ComspecBaudRate9600,
ComPort.eComDataBits.ComspecDataBits8,
ComPort.eComParityType.ComspecParityNone,
ComPort.eComStopBits.ComspecStopBits1,
ComPort.eComProtocolType.ComspecProtocolRS232,
ComPort.eComHardwareHandshakeType.ComspecHardwareHandshakeNone,
ComPort.eComSoftwareHandshakeType.ComspecSoftwareHandshakeNone,
false);
}
// ensure this processor has ethernet then setup the EISC
if (this.SupportsEthernet)
{
myEISC = new EthernetIntersystemCommunications(eISCIPID, eISCIP, this);
if (myEISC.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error(">>> The EISC was not registered: {0}", myEISC.RegistrationFailureReason);
}
else
{
// Device has been registered. Now register for the event handlers
myEISC.OnlineStatusChange += new OnlineStatusChangeEventHandler(myEISC_OnlineStatusChange);
myEISC.SigChange += new SigEventHandler(myEISC_SigChange);
ErrorLog.Notice(">>> The EISC has been registered successfully");
}
}
else
{
ErrorLog.Error(">>> This processor does not support ethernet, so this program will not run");
}
}
public TouchPanelController(CrestronControlSystem controlSystem)
{
_EIScom = new EthernetIntersystemCommunications(0x09, "127.0.0.2", controlSystem);
_EIScom.SigChange += EISComm_SigChange;
}
public ControlSystem()
: base()
{
try
{
Thread.MaxNumberOfUserThreads = 20;
//Hello World Crestron Console
CrestronConsole.AddNewConsoleCommand(HelloPrinting, "HelloWorld", "Prints Hello & the text that follows", ConsoleAccessLevelEnum.AccessOperator);
//Subscribe to the controller events (System, Program, and Ethernet)
CrestronEnvironment.SystemEventHandler += new SystemEventHandler(ControlSystem_ControllerSystemEventHandler);
CrestronEnvironment.ProgramStatusEventHandler += new ProgramStatusEventHandler(ControlSystem_ControllerProgramEventHandler);
CrestronEnvironment.EthernetEventHandler += new EthernetEventHandler(ControlSystem_ControllerEthernetEventHandler);
CrestronConsole.PrintLine("DefaultConstructor Complete"); //Hello World
#region Keypad
if (this.SupportsCresnet) //Make sure the system has CresNet
{
myKeypad = new C2nCbdP(0x25, this);
myKeypad.ButtonStateChange += new ButtonEventHandler(myKeypad_ButtonStateChange);
if (myKeypad.NumberOfVersiPorts > 0) //VersiPort addtion
{
for (uint i = 1; i < 2; i++)
{
myKeypad.VersiPorts[i].SetVersiportConfiguration(eVersiportConfiguration.DigitalInput);
myKeypad.VersiPorts[i].VersiportChange += new VersiportEventHandler(ControlSystem_VersiportChange);
}
}
if (myKeypad.Register() != eDeviceRegistrationUnRegistrationResponse.Success) // Hello World Keypad
{
ErrorLog.Error("Error Registering Keypad on ID 0x25: {0}", myKeypad.RegistrationFailureReason);
}
else
{
myKeypad.Button[1].Name = eButtonName.Up;
myKeypad.Button[2].Name = eButtonName.Down;
}
}
#endregion
#region KeypadWithQuery
//Define Keypad with Device Query
if (this.SupportsCresnet)
{
var QueryResponse = CrestronCresnetHelper.Query();
if (QueryResponse == CrestronCresnetHelper.eCresnetDiscoveryReturnValues.Success)
{
//foreach (CrestronCresnetHelper.DiscoveredDeviceElement Item in CrestronCresnetHelper.DiscoveredElementsList) //Gets a little long so we do the var in instead and it works it out
foreach (var Item in CrestronCresnetHelper.DiscoveredElementsList)
{
if (Item.DeviceModel.ToUpper().Contains("C2N-CBD"))
{
if (myKeypad == null) //Check to make sure we have not done created it already.
{
myKeypad = new C2nCbdP(Item.CresnetId, this);
myKeypad.ButtonStateChange += new ButtonEventHandler(myKeypad_ButtonStateChange);
if (myKeypad.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error Registering Keypad: {0}", myKeypad.RegistrationFailureReason);
myKeypad = null;
}
}
}
}
}
}
#endregion
#region IR
if (this.SupportsIROut)
{
if (ControllerIROutputSlot.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error Registering IR Slot: {0}", ControllerIROutputSlot.DeviceRegistrationFailureReason);
}
else
{
myPort = IROutputPorts[1];
myPort.LoadIRDriver(@"\NVRAM\AppleTV.ir");
foreach (string s in myPort.AvailableStandardIRCmds())
{
CrestronConsole.PrintLine("AppleTV Std: {0}", s);
}
foreach (string s in myPort.AvailableIRCmds())
{
CrestronConsole.PrintLine("AppleTV Std: {0}", s);
}
}
}
#endregion
#region VersiPort
if (this.SupportsVersiport)
{
for (uint i = 1; i <= 2; i++)
{
if (this.VersiPorts[i].Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error Registering Versiport 1: {0}", this.VersiPorts[i].DeviceRegistrationFailureReason);
}
else
{
this.VersiPorts[i].SetVersiportConfiguration(eVersiportConfiguration.DigitalOutput);
}
}
}
#endregion
#region ComPorts
if (this.SupportsComPort)
{
for (uint i = 1; i <= 2; i++)
{
this.ComPorts[i].SerialDataReceived += new ComPortDataReceivedEvent(ControlSystem_SerialDataReceived);
if (this.ComPorts[i].Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error Registering ComPort{0}: {1}", i, ComPorts[i].DeviceRegistrationFailureReason);
}
else
{
this.ComPorts[i].SetComPortSpec(ComPort.eComBaudRates.ComspecBaudRate19200,
ComPort.eComDataBits.ComspecDataBits8,
ComPort.eComParityType.ComspecParityNone,
ComPort.eComStopBits.ComspecStopBits1,
ComPort.eComProtocolType.ComspecProtocolRS232,
ComPort.eComHardwareHandshakeType.ComspecHardwareHandshakeNone,
ComPort.eComSoftwareHandshakeType.ComspecSoftwareHandshakeNone,
false);
}
}
}
#endregion1
#region Touchpanel
if (this.SupportsEthernet)
{
myPanel = new XpanelForSmartGraphics(0x03, this);
myPanel.SigChange += new SigEventHandler(myPanel_SigChange);
if (myPanel.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error in Registering xPanel: {0}", myPanel.RegistrationFailureReason);
}
else
{
myPanel.LoadSmartObjects(@"\NVRAM\xpnl.sgd");
CrestronConsole.PrintLine("Loaded SmartObjects: {0}", myPanel.SmartObjects.Count);
foreach (KeyValuePair <uint, SmartObject> mySmartObject in myPanel.SmartObjects)
{
mySmartObject.Value.SigChange += new SmartObjectSigChangeEventHandler(Value_SigChange);
}
MySigGroup = CreateSigGroup(1, eSigType.String);
MySigGroup.Add(myPanel.StringInput[1]);
MySigGroup.Add(myPanel.StringInput[2]);
}
}
#endregion
#region EISC
if (this.SupportsEthernet)
{
myEISC = new EthernetIntersystemCommunications(0x04, "127.0.0.2", this);
myEISC.SigChange += new SigEventHandler(myEISC_SigChange);
if (myEISC.Register() != eDeviceRegistrationUnRegistrationResponse.Success)
{
ErrorLog.Error("Error in Registering EISC: {0}", myEISC.RegistrationFailureReason);
}
else
{
myEISC.SigChange -= myEISC_SigChange;
}
}
#endregion
}
catch (Exception e)
{
ErrorLog.Error("Error in the constructor: {0}", e.Message);
}
}
