public MainWindow()
{
InitializeComponent();
usbController = new usbDevice(0x04D8, 0x0045);
usbController.usbEvent += new usbDevice.usbEventsHandler(usbEvent_receiver);
usbController.findTargetDevice();
settings = new AppSettings();
settings = config.SetDefaultConfig();
_kflop.initdevice(usbController, settings);
if (UsbConnected)
{
usbController.setSolderingIron1TargetTemperature(380.0f);
usbController.setSolderingIron2TargetTemperature(380.0f);
ConfigLoaded = true;
dispatcherTimer.Tick += new EventHandler(dispatcherTimer_Tick);
dispatcherTimer.Interval = new TimeSpan(0, 0, 2);
dispatcherTimer.Start();
}
}
// setup local variables
public void setVariables(AppSettings _settings)
{
settings = _settings;
}
public AppSettings SetDefaultConfig()
{
AppSettings settings = new AppSettings();
SolderHeadSettings solderhead1 = new SolderHeadSettings();
SolderHeadSettings solderhead2 = new SolderHeadSettings();
solderhead1.IronTargetTemperature = 380;
solderhead1.IronTargetTemperature = 380;
settings.PinsToSolder = 40;
settings.PCBLocation1 = true;
settings.PCBLocation2 = true;
settings.PCBLocation3 = true;
settings.PCBLocation4 = true;
settings.PCBLocation5 = true;
// setup solder head 1
solderhead1.HeadRunEnable = true;
solderhead1.MMPerJoint = 8;
solderhead1.HeatingTime = 100;
solderhead1.LoadSolderDistance = 300;
solderhead1.RetractDistance = 10;
solderhead1.PCBHeight = 26;
solderhead1.SolderRetractDistance = 8;
solderhead1.HeadCPM = 225.0;
solderhead1.HeadVelocity = 4e8;
solderhead1.HeadAcceleration = 4e5;
solderhead1.HeadJerk = 4e6;
solderhead1.FeedCPM = 193.0;
solderhead1.FeedVelocity = 2e3;
solderhead1.FeedAcceleration = 2e3;
solderhead1.FeedJerk = 4e6;
solderhead1.LoadingFeedVelocity = 4e3;
solderhead1.LoadingFeedAcceleration = 5e3;
solderhead1.LoadingFeedJerk = 4e6;
// setup solder head 2
solderhead2.HeadRunEnable = true;
solderhead2.MMPerJoint = 8;
solderhead2.HeatingTime = 100;
solderhead2.LoadSolderDistance = 300;
solderhead2.RetractDistance = 10;
solderhead2.PCBHeight = 26;
solderhead2.SolderRetractDistance = 8;
solderhead2.HeadCPM = 233.0;
solderhead2.HeadVelocity = 4e8;
solderhead2.HeadAcceleration = 4e5;
solderhead2.HeadJerk = 4e6;
solderhead2.FeedCPM = 193.0;
solderhead2.FeedVelocity = 2e3;
solderhead2.FeedAcceleration = 2e3;
solderhead2.FeedJerk = 4e6;
solderhead2.LoadingFeedVelocity = 4e3;
solderhead2.LoadingFeedAcceleration = 5e3;
solderhead2.LoadingFeedJerk = 4e6;
settings.SolderHead1 = solderhead1;
settings.SolderHead2 = solderhead2;
return settings;
}
public void initdevice(usbDevice _usb, AppSettings _settings)
{
settings = _settings;
usb = _usb;
Debug.WriteLine("Init Device");
_Controller = new KMotion_dotNet.KM_Controller();
// AddHandlers();
if (_Controller.BoardID > 0)
{
initdevicesettings();
backgroundWorkerSolderJob.DoWork += worker_DoWork;
backgroundWorkerSolderJob.RunWorkerCompleted += worker_RunWorkerCompleted;
backgroundWorkerSolderJob.WorkerSupportsCancellation = true;
}
else
{
MessageBox.Show("Kflop not detected");
}
}
