/// <summary>
/// 获取极限点
/// </summary>
/// <param name="measureManager"></param>
/// <param name="curves">要计算的曲线</param>
/// <param name="measureDirection">测量方向</param>
/// <param name="secondDirection">第二方向，以防在第一个方向上出现多个极值点</param>
/// <param name="thirdDirection">第三方向</param>
/// <returns>极限点</returns>
public static Point3d MeasureExtreme(this MeasureManager measureManager, IBaseCurve[] curves, Vector3d measureDirection, Vector3d secondDirection, Vector3d thirdDirection)
{
NXOpen.Unit unit1 = WorkPart.UnitCollection.FindObject("MilliMeter");
Point3d origin1 = new Point3d(0.0, 0.0, 0.0);
Direction direction1 = WorkPart.Directions.CreateDirection(origin1, measureDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
Direction direction2 = WorkPart.Directions.CreateDirection(origin1, secondDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
Direction direction3 = WorkPart.Directions.CreateDirection(origin1, thirdDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
ScCollector scCollector1;
scCollector1 = WorkPart.ScCollectors.CreateCollector();
CurveDumbRule curveDumbRule1 = WorkPart.ScRuleFactory.CreateRuleBaseCurveDumb(curves);
SelectionIntentRule[] rules1 = new SelectionIntentRule[1] {
curveDumbRule1
};
scCollector1.ReplaceRules(rules1, false);
MeasureRectangularExtreme extreme = WorkPart.MeasureManager.NewRectangularExtreme(unit1, direction1, direction2, direction3, scCollector1, false);
Point3d extremePoint = extreme.Point;
int nErrs1 = TheSession.UpdateManager.AddToDeleteList(direction1);
scCollector1.Destroy();
return(extremePoint);
}
/// <summary>
/// 测量两个对象集之间的投影距离，只能是当前工作部件中的对象，可用类型为 Point, Curve, Edge, Face, Body, Datum Plane.
/// </summary>
/// <param name="measureManager"></param>
/// <param name="objects1"></param>
/// <param name="objects2"></param>
/// <param name="projectVector">投影矢量</param>
/// <param name="type">测量类型</param>
/// <returns>投影距离值</returns>
public static (bool Success, double Distance, Point3d PointOn1stObjects, Point3d PointOn2ndObjects) MeasureProjectDistance(this MeasureManager measureManager, NXObject[] objects1, NXObject[] objects2, Vector3d projectVector, MeasureManager.ProjectionType type)
{
try
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
Direction direction = WorkPart.Directions.CreateDirection(new Point3d(), projectVector, NXOpen.SmartObject.UpdateOption.WithinModeling);
MeasureDistance minimumMeasure = measureManager.NewScDistance(lengthUnit, CreateCollector(objects1), CreateCollector(objects2), direction, type, true);
Measure measureFeature = minimumMeasure.CreateFeature();
var measureLine = measureFeature.GetEntities()[0] as Line;
var minimumDistance = measureLine.GetLength();
Point3d pointOn1stObjects = measureLine.StartPoint;
Point3d pointOn2ndObjects = measureLine.EndPoint;
measureFeature.Delete();
return(true, minimumDistance, pointOn1stObjects, pointOn2ndObjects);
}
catch (Exception)
{
return(false, 0, new Point3d(), new Point3d());
}
}
/// <summary>
/// 使用 NXOpen 测量两个对象之间的距离
/// </summary>
/// <param name="measureManager"></param>
/// <param name="object1">对象1</param>
/// <param name="object2">对象2</param>
/// <returns>距离值</returns>
public static (bool Success, double Distance, Point3d PointOn1stObject, Point3d PointOn2ndObject) MeasureDistance(this MeasureManager measureManager, DisplayableObject object1, DisplayableObject object2)
{
try
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
MeasureDistance distance = measureManager.NewDistance(lengthUnit, MeasureManager.MeasureType.Minimum, true, object1, object2);
var measureFeature = distance.CreateFeature();
var measureLine = measureFeature.GetEntities()[0] as Line;
var minimumDistance = measureLine.GetLength();
Point3d pointOn1stObject = measureLine.StartPoint;
Point3d pointOn2ndObject = measureLine.EndPoint;
measureFeature.Delete();
return(true, minimumDistance, pointOn1stObject, pointOn2ndObject);
}
catch (Exception)
{
return(false, 0, new Point3d(), new Point3d());
}
}
/// <summary>
/// 测量两个组件集之间的距离
/// </summary>
/// <param name="measureManager"></param>
/// <param name="components1">组件集1</param>
/// <param name="components2">组件集2</param>
/// <returns>距离值</returns>
public static double MeasureDistance(this MeasureManager measureManager, Component[] components1, Component[] components2)
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
ComponentGroup group1 = WorkPart.ComponentGroups.CreateComponentGroup(System.DateTime.Now.ToLongTimeString() + "_1");
for (int i = 0; i < components1.Length; i++)
{
group1.AddComponent(components1[i], false);
}
ComponentGroup group2 = WorkPart.ComponentGroups.CreateComponentGroup(System.DateTime.Now.ToLongTimeString() + "_2");
for (int i = 0; i < components2.Length; i++)
{
group2.AddComponent(components2[i], false);
}
double distanceValue = measureManager.NewDistance(lengthUnit, group1, group2).Value;
group1.Delete();
group2.Delete();
return(distanceValue);
}
/// <summary>
/// 测量两个组件之间的距离
/// </summary>
/// <param name="measureManager"></param>
/// <param name="component1">组件1</param>
/// <param name="component2">组件2</param>
/// <returns>距离值</returns>
public static double MeasureDistance(this MeasureManager measureManager, Component component1, Component component2)
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
double distanceValue = measureManager.NewDistance(lengthUnit, component1, component2).Value;
return(distanceValue);
}
/// <summary>
/// 测量面的属性
/// </summary>
/// <param name="theMeasureManaer"></param>
/// <param name="faces"></param>
/// <param name="tolerance">测量公差，越接近1.0，结果越精确，但同时可能会花费较长时间</param>
/// <returns></returns>
public static MeasureFaces MeasureFace(this MeasureManager theMeasureManaer, Face[] faces, double tolerance = 0.999)
{
NXOpen.Unit areaUnit = WorkPart.UnitCollection.FindObject("SquareMilliMeter");
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
MeasureFaces measureFace = WorkPart.MeasureManager.NewFaceProperties(areaUnit, lengthUnit, tolerance, faces);
return(measureFace);
}
/// <summary>
/// 测量两个对象之间的投影距离
/// </summary>
/// <param name="measureManager"></param>
/// <param name="object1">对象1</param>
/// <param name="object2">对象2</param>
/// <param name="projectVector">投影矢量</param>
/// <param name="type">测量类型</param>
/// <returns>投影距离值</returns>
public static double MeasureProjectDistance(this MeasureManager measureManager, DisplayableObject object1, DisplayableObject object2, Vector3d projectVector, MeasureManager.ProjectionType type)
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
Direction direction1 = WorkPart.Directions.CreateDirection(new Point3d(), projectVector, NXOpen.SmartObject.UpdateOption.WithinModeling);
var projectDistance = measureManager.NewDistance(lengthUnit, object1, object2, direction1, type);
return(projectDistance.Value);
}
public static Snap.NX.Unit Wrap(Tag nxopenUnitTag)
{
if (nxopenUnitTag == Tag.Null)
{
throw new ArgumentException("Input tag is NXOpen.Tag.Null");
}
NXOpen.Unit objectFromTag = Snap.NX.NXObject.GetObjectFromTag(nxopenUnitTag) as NXOpen.Unit;
if (objectFromTag == null)
{
throw new ArgumentException("Input tag doesn't belong to an NXOpen.Unit object");
}
return(objectFromTag);
}
/// <summary>
/// 获取极限点
/// </summary>
/// <param name="measureManager"></param>
/// <param name="faces">要进行计算的面</param>
/// <param name="measureDirection">第一个方向</param>
/// <param name="secondDirection">第二个方向</param>
/// <param name="thirdDirection">第三个方向</param>
/// <returns>结果点</returns>
public static Point3d MeasureExtreme(this MeasureManager measureManager, Face[] faces, Vector3d measureDirection, Vector3d secondDirection, Vector3d thirdDirection)
{
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
#if NX12
FaceDumbRule faceDumbRule = (WorkPart as BasePart).ScRuleFactory.CreateRuleFaceDumb(faces);
#else
FaceDumbRule faceDumbRule = WorkPart.ScRuleFactory.CreateRuleFaceDumb(faces);
#endif
ScCollector scCollector = WorkPart.ScCollectors.CreateCollector();
scCollector.ReplaceRules(new SelectionIntentRule[] { faceDumbRule }, false);
Direction direction1 = WorkPart.Directions.CreateDirection(new Point3d(), measureDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
Direction direction2 = WorkPart.Directions.CreateDirection(new Point3d(), secondDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
Direction direction3 = WorkPart.Directions.CreateDirection(new Point3d(), thirdDirection, NXOpen.SmartObject.UpdateOption.WithinModeling);
var facesExtreme = measureManager.NewRectangularExtreme(lengthUnit, direction1, direction2, direction3, scCollector, false);
return(facesExtreme.Point);
}
/// <summary>
/// 测量点到一组对象之间的最短距离，只能是当前工作部件中的对象，可用类型为 Point, Curve, Edge, Face, Body, Datum Plane.
/// </summary>
/// <param name="measureManager"></param>
/// <param name="point">出发点</param>
/// <param name="objects"></param>
/// <returns>距离值</returns>
public static (bool Success, double Distance, Point3d PointOnObjects) MeasureDistance(this MeasureManager measureManager, Point3d point, NXObject[] objects)
{
try
{
#if NX12
NXOpen.CurveDumbRule curveDumbRule1 = (WorkPart as BasePart).ScRuleFactory.CreateRuleCurveDumbFromPoints(new Point[] { WorkPart.Points.CreatePoint(point) });
#else
NXOpen.CurveDumbRule curveDumbRule1 = WorkPart.ScRuleFactory.CreateRuleCurveDumbFromPoints(new Point[] { WorkPart.Points.CreatePoint(point) });
#endif
ScCollector scCollector1 = WorkPart.ScCollectors.CreateCollector();
scCollector1.ReplaceRules(new SelectionIntentRule[] { curveDumbRule1 }, false);
ScCollector scCollector2 = CreateCollector(objects);
NXOpen.Unit lengthUnit = WorkPart.UnitCollection.FindObject("MilliMeter");
var minimumMeasure = measureManager.NewScDistance(lengthUnit, MeasureManager.MeasureType.Minimum, true, scCollector1, scCollector2);
var measureFeature = minimumMeasure.CreateFeature();
var measureLine = measureFeature.GetEntities()[0] as Line;
var minimumDistance = measureLine.GetLength();
Point3d pointOnObjects = measureLine.EndPoint;
measureFeature.Delete();
return(true, minimumDistance, pointOnObjects);
}
catch (Exception)
{
return(false, 0, new Point3d());
}
}
public static void Main(string[] args)
{
Console.WriteLine("Starting NX Golden Cantilever Journal");
//Declare Part Variables
//Convert Strings to doubles from the args
double heightA = System.Convert.ToDouble(args[0]);
double length = System.Convert.ToDouble(args[1]);
double thickness = System.Convert.ToDouble(args[2]);
//Declare part name for the part file and the IGES file
string part_name = args[3];
string part_name_prt = part_name + ".prt";
string part_name_igs = part_name + ".igs";
//Measurements need to be converted from m to mm
//length = 1000 * length;
//thickness = 1000 * thickness;
//heightA = 1000 * heightA;
double heightB = 1.618 * heightA;
//Convert necessary values back to strings because I already
//converted them to doubles and I'm too lazy to go back and change
//this since it works.
string length_string = System.Convert.ToString(length);
string thickness_string = System.Convert.ToString(thickness);
string heightA_string = System.Convert.ToString(heightA);
string heightB_string = System.Convert.ToString(heightB);
NXOpen.Session theSession = NXOpen.Session.GetSession();
// ----------------------------------------------
// Menu: File->New...
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId1;
markId1 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Start");
NXOpen.FileNew fileNew1;
fileNew1 = theSession.Parts.FileNew();
theSession.SetUndoMarkName(markId1, "New Dialog");
NXOpen.Session.UndoMarkId markId2;
markId2 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "New");
theSession.DeleteUndoMark(markId2, null);
NXOpen.Session.UndoMarkId markId3;
markId3 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "New");
fileNew1.TemplateFileName = "model-plain-1-mm-template.prt";
fileNew1.UseBlankTemplate = false;
fileNew1.ApplicationName = "ModelTemplate";
fileNew1.Units = NXOpen.Part.Units.Millimeters;
fileNew1.RelationType = "";
fileNew1.UsesMasterModel = "No";
fileNew1.TemplateType = NXOpen.FileNewTemplateType.Item;
fileNew1.TemplatePresentationName = "Model";
fileNew1.ItemType = "";
fileNew1.Specialization = "";
fileNew1.SetCanCreateAltrep(false);
fileNew1.NewFileName = part_name_prt;
fileNew1.MasterFileName = "";
fileNew1.MakeDisplayedPart = true;
NXOpen.NXObject nXObject1;
nXObject1 = fileNew1.Commit();
NXOpen.Part workPart = theSession.Parts.Work;
NXOpen.Part displayPart = theSession.Parts.Display;
theSession.DeleteUndoMark(markId3, null);
fileNew1.Destroy();
theSession.ApplicationSwitchImmediate("UG_APP_MODELING");
NXOpen.Session.UndoMarkId markId4;
markId4 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Enter Gateway");
NXOpen.Session.UndoMarkId markId5;
markId5 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Enter Modeling");
// ----------------------------------------------
// Menu: Insert->Sketch...
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId6;
markId6 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Start");
NXOpen.Sketch nullNXOpen_Sketch = null;
NXOpen.SketchInPlaceBuilder sketchInPlaceBuilder1;
sketchInPlaceBuilder1 = workPart.Sketches.CreateNewSketchInPlaceBuilder(nullNXOpen_Sketch);
NXOpen.Unit unit1 = (NXOpen.Unit)workPart.UnitCollection.FindObject("MilliMeter");
NXOpen.Expression expression1;
expression1 = workPart.Expressions.CreateSystemExpressionWithUnits("0", unit1);
NXOpen.Expression expression2;
expression2 = workPart.Expressions.CreateSystemExpressionWithUnits("0", unit1);
NXOpen.SketchAlongPathBuilder sketchAlongPathBuilder1;
sketchAlongPathBuilder1 = workPart.Sketches.CreateSketchAlongPathBuilder(nullNXOpen_Sketch);
sketchAlongPathBuilder1.PlaneLocation.Expression.RightHandSide = "0";
theSession.SetUndoMarkName(markId6, "Create Sketch Dialog");
NXOpen.DatumPlane datumPlane1 = (NXOpen.DatumPlane)workPart.Datums.FindObject("DATUM_CSYS(0) YZ plane");
NXOpen.Point3d point1 = new NXOpen.Point3d(11.1863449593062, 6.4875984180345, 0.0);
sketchInPlaceBuilder1.PlaneOrFace.SetValue(datumPlane1, workPart.ModelingViews.WorkView, point1);
NXOpen.Features.DatumCsys datumCsys1 = (NXOpen.Features.DatumCsys)workPart.Features.FindObject("DATUM_CSYS(0)");
NXOpen.Point point2 = (NXOpen.Point)datumCsys1.FindObject("POINT 1");
sketchInPlaceBuilder1.SketchOrigin = point2;
sketchInPlaceBuilder1.PlaneOrFace.Value = null;
sketchInPlaceBuilder1.PlaneOrFace.Value = datumPlane1;
NXOpen.DatumAxis datumAxis1 = (NXOpen.DatumAxis)workPart.Datums.FindObject("DATUM_CSYS(0) X axis");
sketchInPlaceBuilder1.Axis.Value = datumAxis1;
NXOpen.Session.UndoMarkId markId7;
markId7 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Create Sketch");
theSession.DeleteUndoMark(markId7, null);
NXOpen.Session.UndoMarkId markId8;
markId8 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Create Sketch");
theSession.Preferences.Sketch.CreateInferredConstraints = true;
theSession.Preferences.Sketch.ContinuousAutoDimensioning = true;
theSession.Preferences.Sketch.DimensionLabel = NXOpen.Preferences.SketchPreferences.DimensionLabelType.Expression;
theSession.Preferences.Sketch.TextSizeFixed = true;
theSession.Preferences.Sketch.FixedTextSize = 3.0;
theSession.Preferences.Sketch.ConstraintSymbolSize = 3.0;
theSession.Preferences.Sketch.DisplayObjectColor = false;
theSession.Preferences.Sketch.DisplayObjectName = true;
NXOpen.NXObject nXObject2;
nXObject2 = sketchInPlaceBuilder1.Commit();
NXOpen.Sketch sketch1 = (NXOpen.Sketch)nXObject2;
NXOpen.Features.Feature feature1;
feature1 = sketch1.Feature;
NXOpen.Session.UndoMarkId markId9;
markId9 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "update");
int nErrs1;
nErrs1 = theSession.UpdateManager.DoUpdate(markId9);
sketch1.Activate(NXOpen.Sketch.ViewReorient.True);
theSession.DeleteUndoMark(markId8, null);
theSession.SetUndoMarkName(markId6, "Create Sketch");
sketchInPlaceBuilder1.Destroy();
sketchAlongPathBuilder1.Destroy();
try
{
// Expression is still in use.
workPart.Expressions.Delete(expression2);
}
catch (NXException ex)
{
ex.AssertErrorCode(1050029);
}
try
{
// Expression is still in use.
workPart.Expressions.Delete(expression1);
}
catch (NXException ex)
{
ex.AssertErrorCode(1050029);
}
// ----------------------------------------------
// Menu: Insert->Sketch Curve->Line...
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId10;
markId10 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Profile short list");
NXOpen.Session.UndoMarkId markId11;
markId11 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Curve");
NXOpen.Expression expression3;
expression3 = workPart.Expressions.CreateSystemExpression(length_string);
theSession.SetUndoMarkVisibility(markId11, "Curve", NXOpen.Session.MarkVisibility.Visible);
NXOpen.Point3d startPoint1 = new NXOpen.Point3d(0.0, 0.0, 0.0);
NXOpen.Point3d endPoint1 = new NXOpen.Point3d(length, 0.0, 0.0);
NXOpen.Line line1;
line1 = workPart.Curves.CreateLine(startPoint1, endPoint1);
theSession.ActiveSketch.AddGeometry(line1, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
NXOpen.Sketch.ConstraintGeometry geom1_1 = new NXOpen.Sketch.ConstraintGeometry();
geom1_1.Geometry = line1;
geom1_1.PointType = NXOpen.Sketch.ConstraintPointType.StartVertex;
geom1_1.SplineDefiningPointIndex = 0;
NXOpen.Sketch.ConstraintGeometry geom2_1 = new NXOpen.Sketch.ConstraintGeometry();
NXOpen.Features.DatumCsys datumCsys2 = (NXOpen.Features.DatumCsys)workPart.Features.FindObject("SKETCH(1:1B)");
NXOpen.Point point3 = (NXOpen.Point)datumCsys2.FindObject("POINT 1");
geom2_1.Geometry = point3;
geom2_1.PointType = NXOpen.Sketch.ConstraintPointType.None;
geom2_1.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint1;
sketchGeometricConstraint1 = theSession.ActiveSketch.CreateCoincidentConstraint(geom1_1, geom2_1);
NXOpen.Sketch.ConstraintGeometry geom1 = new NXOpen.Sketch.ConstraintGeometry();
geom1.Geometry = line1;
geom1.PointType = NXOpen.Sketch.ConstraintPointType.None;
geom1.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint2;
sketchGeometricConstraint2 = theSession.ActiveSketch.CreateHorizontalConstraint(geom1);
NXOpen.Sketch.DimensionGeometry dimObject1_1 = new NXOpen.Sketch.DimensionGeometry();
dimObject1_1.Geometry = line1;
dimObject1_1.AssocType = NXOpen.Sketch.AssocType.StartPoint;
dimObject1_1.AssocValue = 0;
dimObject1_1.HelpPoint.X = 0.0;
dimObject1_1.HelpPoint.Y = 0.0;
dimObject1_1.HelpPoint.Z = 0.0;
NXOpen.NXObject nullNXOpen_NXObject = null;
dimObject1_1.View = nullNXOpen_NXObject;
NXOpen.Sketch.DimensionGeometry dimObject2_1 = new NXOpen.Sketch.DimensionGeometry();
dimObject2_1.Geometry = line1;
dimObject2_1.AssocType = NXOpen.Sketch.AssocType.EndPoint;
dimObject2_1.AssocValue = 0;
dimObject2_1.HelpPoint.X = 0.0;
dimObject2_1.HelpPoint.Y = 0.0;
dimObject2_1.HelpPoint.Z = 0.0;
dimObject2_1.View = nullNXOpen_NXObject;
NXOpen.Point3d dimOrigin1 = new NXOpen.Point3d(45.0, -9.0598069411704, 0.0);
NXOpen.SketchDimensionalConstraint sketchDimensionalConstraint1;
sketchDimensionalConstraint1 = theSession.ActiveSketch.CreateDimension(NXOpen.Sketch.ConstraintType.ParallelDim, dimObject1_1, dimObject2_1, dimOrigin1, expression3, NXOpen.Sketch.DimensionOption.CreateAsDriving);
NXOpen.SketchHelpedDimensionalConstraint sketchHelpedDimensionalConstraint1 = (NXOpen.SketchHelpedDimensionalConstraint)sketchDimensionalConstraint1;
NXOpen.Annotations.Dimension dimension1;
dimension1 = sketchHelpedDimensionalConstraint1.AssociatedDimension;
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId12;
markId12 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Curve");
NXOpen.Expression expression4;
expression4 = workPart.Expressions.CreateSystemExpression(heightA_string);
NXOpen.Expression expression5;
expression5 = workPart.Expressions.CreateSystemExpression(length_string);
workPart.Expressions.Edit(expression4, heightA_string);
theSession.SetUndoMarkVisibility(markId12, "Curve", NXOpen.Session.MarkVisibility.Visible);
NXOpen.Point3d startPoint2 = new NXOpen.Point3d(length, 0.0, 0.0);
NXOpen.Point3d endPoint2 = new NXOpen.Point3d(length, heightA, 0.0);
NXOpen.Line line2;
line2 = workPart.Curves.CreateLine(startPoint2, endPoint2);
theSession.ActiveSketch.AddGeometry(line2, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
NXOpen.Sketch.ConstraintGeometry geom1_2 = new NXOpen.Sketch.ConstraintGeometry();
geom1_2.Geometry = line2;
geom1_2.PointType = NXOpen.Sketch.ConstraintPointType.StartVertex;
geom1_2.SplineDefiningPointIndex = 0;
NXOpen.Sketch.ConstraintGeometry geom2_2 = new NXOpen.Sketch.ConstraintGeometry();
geom2_2.Geometry = line1;
geom2_2.PointType = NXOpen.Sketch.ConstraintPointType.EndVertex;
geom2_2.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint3;
sketchGeometricConstraint3 = theSession.ActiveSketch.CreateCoincidentConstraint(geom1_2, geom2_2);
NXOpen.Sketch.ConstraintGeometry geom2 = new NXOpen.Sketch.ConstraintGeometry();
geom2.Geometry = line2;
geom2.PointType = NXOpen.Sketch.ConstraintPointType.None;
geom2.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint4;
sketchGeometricConstraint4 = theSession.ActiveSketch.CreateVerticalConstraint(geom2);
workPart.Expressions.Delete(expression5);
NXOpen.Sketch.DimensionGeometry dimObject1_2 = new NXOpen.Sketch.DimensionGeometry();
dimObject1_2.Geometry = line2;
dimObject1_2.AssocType = NXOpen.Sketch.AssocType.StartPoint;
dimObject1_2.AssocValue = 0;
dimObject1_2.HelpPoint.X = 0.0;
dimObject1_2.HelpPoint.Y = 0.0;
dimObject1_2.HelpPoint.Z = 0.0;
dimObject1_2.View = nullNXOpen_NXObject;
NXOpen.Sketch.DimensionGeometry dimObject2_2 = new NXOpen.Sketch.DimensionGeometry();
dimObject2_2.Geometry = line2;
dimObject2_2.AssocType = NXOpen.Sketch.AssocType.EndPoint;
dimObject2_2.AssocValue = 0;
dimObject2_2.HelpPoint.X = 0.0;
dimObject2_2.HelpPoint.Y = 0.0;
dimObject2_2.HelpPoint.Z = 0.0;
dimObject2_2.View = nullNXOpen_NXObject;
NXOpen.Point3d dimOrigin2 = new NXOpen.Point3d(99.0598069411704, 15.0, 0.0);
NXOpen.SketchDimensionalConstraint sketchDimensionalConstraint2;
sketchDimensionalConstraint2 = theSession.ActiveSketch.CreateDimension(NXOpen.Sketch.ConstraintType.ParallelDim, dimObject1_2, dimObject2_2, dimOrigin2, expression4, NXOpen.Sketch.DimensionOption.CreateAsDriving);
NXOpen.SketchHelpedDimensionalConstraint sketchHelpedDimensionalConstraint2 = (NXOpen.SketchHelpedDimensionalConstraint)sketchDimensionalConstraint2;
NXOpen.Annotations.Dimension dimension2;
dimension2 = sketchHelpedDimensionalConstraint2.AssociatedDimension;
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId13;
markId13 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Curve");
NXOpen.Expression expression6;
expression6 = workPart.Expressions.CreateSystemExpression(heightB_string);
NXOpen.Expression expression7;
expression7 = workPart.Expressions.CreateSystemExpression(length_string);
theSession.SetUndoMarkVisibility(markId13, "Curve", NXOpen.Session.MarkVisibility.Visible);
NXOpen.Point3d startPoint3 = new NXOpen.Point3d(0.0, 0.0, 0.0);
NXOpen.Point3d endPoint3 = new NXOpen.Point3d(7.02873218749514e-014, heightB, 0.0);
NXOpen.Line line3;
line3 = workPart.Curves.CreateLine(startPoint3, endPoint3);
theSession.ActiveSketch.AddGeometry(line3, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
NXOpen.Sketch.ConstraintGeometry geom1_3 = new NXOpen.Sketch.ConstraintGeometry();
geom1_3.Geometry = line3;
geom1_3.PointType = NXOpen.Sketch.ConstraintPointType.StartVertex;
geom1_3.SplineDefiningPointIndex = 0;
NXOpen.Sketch.ConstraintGeometry geom2_3 = new NXOpen.Sketch.ConstraintGeometry();
geom2_3.Geometry = line1;
geom2_3.PointType = NXOpen.Sketch.ConstraintPointType.StartVertex;
geom2_3.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint5;
sketchGeometricConstraint5 = theSession.ActiveSketch.CreateCoincidentConstraint(geom1_3, geom2_3);
NXOpen.Sketch.ConstraintGeometry geom3 = new NXOpen.Sketch.ConstraintGeometry();
geom3.Geometry = line3;
geom3.PointType = NXOpen.Sketch.ConstraintPointType.None;
geom3.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint6;
sketchGeometricConstraint6 = theSession.ActiveSketch.CreateVerticalConstraint(geom3);
workPart.Expressions.Delete(expression7);
NXOpen.Sketch.DimensionGeometry dimObject1_3 = new NXOpen.Sketch.DimensionGeometry();
dimObject1_3.Geometry = line3;
dimObject1_3.AssocType = NXOpen.Sketch.AssocType.StartPoint;
dimObject1_3.AssocValue = 0;
dimObject1_3.HelpPoint.X = 0.0;
dimObject1_3.HelpPoint.Y = 0.0;
dimObject1_3.HelpPoint.Z = 0.0;
dimObject1_3.View = nullNXOpen_NXObject;
NXOpen.Sketch.DimensionGeometry dimObject2_3 = new NXOpen.Sketch.DimensionGeometry();
dimObject2_3.Geometry = line3;
dimObject2_3.AssocType = NXOpen.Sketch.AssocType.EndPoint;
dimObject2_3.AssocValue = 0;
dimObject2_3.HelpPoint.X = 0.0;
dimObject2_3.HelpPoint.Y = 0.0;
dimObject2_3.HelpPoint.Z = 0.0;
dimObject2_3.View = nullNXOpen_NXObject;
NXOpen.Point3d dimOrigin3 = new NXOpen.Point3d(9.05980694117043, heightA, 0.0);
NXOpen.SketchDimensionalConstraint sketchDimensionalConstraint3;
sketchDimensionalConstraint3 = theSession.ActiveSketch.CreateDimension(NXOpen.Sketch.ConstraintType.ParallelDim, dimObject1_3, dimObject2_3, dimOrigin3, expression6, NXOpen.Sketch.DimensionOption.CreateAsDriving);
NXOpen.SketchHelpedDimensionalConstraint sketchHelpedDimensionalConstraint3 = (NXOpen.SketchHelpedDimensionalConstraint)sketchDimensionalConstraint3;
NXOpen.Annotations.Dimension dimension3;
dimension3 = sketchHelpedDimensionalConstraint3.AssociatedDimension;
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId14;
markId14 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Curve");
theSession.SetUndoMarkVisibility(markId14, "Curve", NXOpen.Session.MarkVisibility.Visible);
NXOpen.Point3d startPoint4 = new NXOpen.Point3d(0.0, heightB, 0.0);
NXOpen.Point3d endPoint4 = new NXOpen.Point3d(length, heightA, 0.0);
//NXOpen.Point3d endPoint4 = new NXOpen.Point3d(90.0, 29.9999999999998, 0.0);
NXOpen.Line line4;
line4 = workPart.Curves.CreateLine(startPoint4, endPoint4);
theSession.ActiveSketch.AddGeometry(line4, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
NXOpen.Sketch.ConstraintGeometry geom1_4 = new NXOpen.Sketch.ConstraintGeometry();
geom1_4.Geometry = line4;
geom1_4.PointType = NXOpen.Sketch.ConstraintPointType.StartVertex;
geom1_4.SplineDefiningPointIndex = 0;
NXOpen.Sketch.ConstraintGeometry geom2_4 = new NXOpen.Sketch.ConstraintGeometry();
geom2_4.Geometry = line3;
geom2_4.PointType = NXOpen.Sketch.ConstraintPointType.EndVertex;
geom2_4.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint7;
sketchGeometricConstraint7 = theSession.ActiveSketch.CreateCoincidentConstraint(geom1_4, geom2_4);
NXOpen.Sketch.ConstraintGeometry geom1_5 = new NXOpen.Sketch.ConstraintGeometry();
geom1_5.Geometry = line4;
geom1_5.PointType = NXOpen.Sketch.ConstraintPointType.EndVertex;
geom1_5.SplineDefiningPointIndex = 0;
NXOpen.Sketch.ConstraintGeometry geom2_5 = new NXOpen.Sketch.ConstraintGeometry();
geom2_5.Geometry = line2;
geom2_5.PointType = NXOpen.Sketch.ConstraintPointType.EndVertex;
geom2_5.SplineDefiningPointIndex = 0;
NXOpen.SketchGeometricConstraint sketchGeometricConstraint8;
sketchGeometricConstraint8 = theSession.ActiveSketch.CreateCoincidentConstraint(geom1_5, geom2_5);
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
// ----------------------------------------------
// Menu: File->Finish Sketch
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId15;
markId15 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Deactivate Sketch");
theSession.ActiveSketch.Deactivate(NXOpen.Sketch.ViewReorient.False, NXOpen.Sketch.UpdateLevel.Model);
// ----------------------------------------------
// Menu: Insert->Design Feature->Extrude...
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId16;
markId16 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Start");
NXOpen.Features.Feature nullNXOpen_Features_Feature = null;
if (!workPart.Preferences.Modeling.GetHistoryMode())
{
throw new Exception("Create or edit of a Feature was recorded in History Mode but playback is in History-Free Mode.");
}
NXOpen.Features.ExtrudeBuilder extrudeBuilder1;
extrudeBuilder1 = workPart.Features.CreateExtrudeBuilder(nullNXOpen_Features_Feature);
NXOpen.Section section1;
section1 = workPart.Sections.CreateSection(0.0095, 0.01, 0.5);
extrudeBuilder1.Section = section1;
extrudeBuilder1.AllowSelfIntersectingSection(true);
NXOpen.Unit unit2;
unit2 = extrudeBuilder1.Draft.FrontDraftAngle.Units;
NXOpen.Expression expression8;
expression8 = workPart.Expressions.CreateSystemExpressionWithUnits("2.00", unit2);
extrudeBuilder1.DistanceTolerance = 0.01;
extrudeBuilder1.BooleanOperation.Type = NXOpen.GeometricUtilities.BooleanOperation.BooleanType.Create;
NXOpen.Body[] targetBodies1 = new NXOpen.Body[1];
NXOpen.Body nullNXOpen_Body = null;
targetBodies1[0] = nullNXOpen_Body;
extrudeBuilder1.BooleanOperation.SetTargetBodies(targetBodies1);
extrudeBuilder1.Limits.StartExtend.Value.RightHandSide = "0";
extrudeBuilder1.Limits.EndExtend.Value.RightHandSide = "25";
extrudeBuilder1.Offset.StartOffset.RightHandSide = "0";
extrudeBuilder1.Offset.EndOffset.RightHandSide = "5";
extrudeBuilder1.Limits.StartExtend.Value.RightHandSide = "0";
extrudeBuilder1.Limits.EndExtend.Value.RightHandSide = thickness_string;
extrudeBuilder1.Draft.FrontDraftAngle.RightHandSide = "2";
extrudeBuilder1.Draft.BackDraftAngle.RightHandSide = "2";
extrudeBuilder1.Offset.StartOffset.RightHandSide = "0";
extrudeBuilder1.Offset.EndOffset.RightHandSide = "5";
NXOpen.GeometricUtilities.SmartVolumeProfileBuilder smartVolumeProfileBuilder1;
smartVolumeProfileBuilder1 = extrudeBuilder1.SmartVolumeProfile;
smartVolumeProfileBuilder1.OpenProfileSmartVolumeOption = false;
smartVolumeProfileBuilder1.CloseProfileRule = NXOpen.GeometricUtilities.SmartVolumeProfileBuilder.CloseProfileRuleType.Fci;
theSession.SetUndoMarkName(markId16, "Extrude Dialog");
section1.DistanceTolerance = 0.01;
section1.ChainingTolerance = 0.0095;
section1.SetAllowedEntityTypes(NXOpen.Section.AllowTypes.OnlyCurves);
NXOpen.Session.UndoMarkId markId17;
markId17 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "section mark");
NXOpen.Session.UndoMarkId markId18;
markId18 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, null);
NXOpen.Features.Feature[] features1 = new NXOpen.Features.Feature[1];
NXOpen.Features.SketchFeature sketchFeature1 = (NXOpen.Features.SketchFeature)feature1;
features1[0] = sketchFeature1;
NXOpen.CurveFeatureRule curveFeatureRule1;
curveFeatureRule1 = workPart.ScRuleFactory.CreateRuleCurveFeature(features1);
section1.AllowSelfIntersection(true);
NXOpen.SelectionIntentRule[] rules1 = new NXOpen.SelectionIntentRule[1];
rules1[0] = curveFeatureRule1;
NXOpen.Point3d helpPoint1 = new NXOpen.Point3d(53.8762063337749, 42.0412645554082, 0.0);
section1.AddToSection(rules1, line4, nullNXOpen_NXObject, nullNXOpen_NXObject, helpPoint1, NXOpen.Section.Mode.Create, false);
theSession.DeleteUndoMark(markId18, null);
NXOpen.Direction direction1;
direction1 = workPart.Directions.CreateDirection(sketch1, NXOpen.Sense.Forward, NXOpen.SmartObject.UpdateOption.WithinModeling);
extrudeBuilder1.Direction = direction1;
theSession.DeleteUndoMark(markId17, null);
NXOpen.Session.UndoMarkId markId19;
markId19 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Extrude");
theSession.DeleteUndoMark(markId19, null);
NXOpen.Session.UndoMarkId markId20;
markId20 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Extrude");
extrudeBuilder1.ParentFeatureInternal = false;
NXOpen.Features.Feature feature2;
feature2 = extrudeBuilder1.CommitFeature();
theSession.DeleteUndoMark(markId20, null);
theSession.SetUndoMarkName(markId16, "Extrude");
NXOpen.Expression expression9 = extrudeBuilder1.Limits.StartExtend.Value;
NXOpen.Expression expression10 = extrudeBuilder1.Limits.EndExtend.Value;
extrudeBuilder1.Destroy();
workPart.Expressions.Delete(expression8);
// ----------------------------------------------
// Menu: File->Save
// ----------------------------------------------
NXOpen.PartSaveStatus partSaveStatus1;
partSaveStatus1 = workPart.Save(NXOpen.BasePart.SaveComponents.True, NXOpen.BasePart.CloseAfterSave.False);
partSaveStatus1.Dispose();
// ----------------------------------------------
// Menu: File->Export->IGES...
// ----------------------------------------------
NXOpen.Session.UndoMarkId markId21;
markId21 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Visible, "Start");
NXOpen.IgesCreator igesCreator1;
igesCreator1 = theSession.DexManager.CreateIgesCreator();
igesCreator1.ExportModelData = true;
igesCreator1.ExportDrawings = true;
igesCreator1.MapTabCylToBSurf = true;
igesCreator1.BcurveTol = 0.0508;
igesCreator1.IdenticalPointResolution = 0.001;
igesCreator1.MaxThreeDMdlSpace = 10000.0;
igesCreator1.ObjectTypes.Curves = true;
igesCreator1.ObjectTypes.Surfaces = true;
igesCreator1.ObjectTypes.Annotations = true;
igesCreator1.ObjectTypes.Structures = true;
igesCreator1.ObjectTypes.Solids = true;
igesCreator1.OutputFile = part_name_igs;
igesCreator1.SettingsFile = "C:\\Program Files\\Siemens\\NX 10.0\\iges\\igesexport.def";
igesCreator1.MaxLineThickness = 2.0;
igesCreator1.SysDefmaxThreeDMdlSpace = true;
igesCreator1.SysDefidenticalPointResolution = true;
igesCreator1.InputFile = part_name_prt;
igesCreator1.OutputFile = part_name_igs;
theSession.SetUndoMarkName(markId21, "Export to IGES Options Dialog");
igesCreator1.OutputFile = part_name_igs;
NXOpen.Session.UndoMarkId markId22;
markId22 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Export to IGES Options");
theSession.DeleteUndoMark(markId22, null);
NXOpen.Session.UndoMarkId markId23;
markId23 = theSession.SetUndoMark(NXOpen.Session.MarkVisibility.Invisible, "Export to IGES Options");
igesCreator1.FileSaveFlag = false;
igesCreator1.LayerMask = "1-256";
igesCreator1.DrawingList = "";
igesCreator1.ViewList = "Top,Front,Right,Back,Bottom,Left,Isometric,Trimetric,User Defined";
NXOpen.NXObject nXObject3;
nXObject3 = igesCreator1.Commit();
theSession.DeleteUndoMark(markId23, null);
theSession.SetUndoMarkName(markId21, "Export to IGES Options");
igesCreator1.Destroy();
// ----------------------------------------------
// Menu: Tools->Journal->Stop Recording
// ----------------------------------------------
Console.WriteLine("Finishing NX Golden Cantilever Journal");
}
internal Unit(NXOpen.Unit unit) : base(unit)
{
this.NXOpenUnit = unit;
}
public static void Main(string[] args)
{
NXOpen.Session theSession = NXOpen.Session.GetSession();
// ----------------------------------------------
// Menu: File->New...
// ----------------------------------------------
//Variable Declaration
double a = double.Parse(args[0]);
double G = 1.618;
double b = G * a;
double L = 10;
double t = double.Parse(args[1]);
NXOpen.FileNew fileNew1;
fileNew1 = theSession.Parts.FileNew();
fileNew1.TemplateFileName = "model-plain-1-mm-template.prt";
fileNew1.UseBlankTemplate = false;
fileNew1.ApplicationName = "ModelTemplate";
fileNew1.Units = NXOpen.Part.Units.Millimeters;
fileNew1.RelationType = "";
fileNew1.UsesMasterModel = "No";
fileNew1.TemplateType = NXOpen.FileNewTemplateType.Item;
fileNew1.TemplatePresentationName = "Model";
fileNew1.ItemType = "";
fileNew1.Specialization = "";
fileNew1.SetCanCreateAltrep(false);
fileNew1.NewFileName = "J:\\ME 578 Systems\\Midterm\\MidtermProject\\GoldBeam.prt";
fileNew1.MasterFileName = "";
fileNew1.MakeDisplayedPart = true;
NXOpen.NXObject nXObject1;
nXObject1 = fileNew1.Commit();
NXOpen.Part workPart = theSession.Parts.Work;
NXOpen.Part displayPart = theSession.Parts.Display;
fileNew1.Destroy();
theSession.ApplicationSwitchImmediate("UG_APP_MODELING");
// ----------------------------------------------
// Menu: Insert->Sketch...
// ----------------------------------------------
NXOpen.Sketch nullNXOpen_Sketch = null;
NXOpen.SketchInPlaceBuilder sketchInPlaceBuilder1;
sketchInPlaceBuilder1 = workPart.Sketches.CreateNewSketchInPlaceBuilder(nullNXOpen_Sketch);
NXOpen.Unit unit1 = (NXOpen.Unit)workPart.UnitCollection.FindObject("MilliMeter");
NXOpen.Expression expression1;
expression1 = workPart.Expressions.CreateSystemExpressionWithUnits("0", unit1);
NXOpen.Expression expression2;
expression2 = workPart.Expressions.CreateSystemExpressionWithUnits("0", unit1);
NXOpen.SketchAlongPathBuilder sketchAlongPathBuilder1;
sketchAlongPathBuilder1 = workPart.Sketches.CreateSketchAlongPathBuilder(nullNXOpen_Sketch);
sketchAlongPathBuilder1.PlaneLocation.Expression.RightHandSide = "0";
NXOpen.DatumPlane datumPlane1 = (NXOpen.DatumPlane)workPart.Datums.FindObject("DATUM_CSYS(0) YZ plane");
NXOpen.Point3d point1 = new NXOpen.Point3d(0, 0, 0);
sketchInPlaceBuilder1.PlaneOrFace.SetValue(datumPlane1, workPart.ModelingViews.WorkView, point1);
NXOpen.Features.DatumCsys datumCsys1 = (NXOpen.Features.DatumCsys)workPart.Features.FindObject("DATUM_CSYS(0)");
NXOpen.Point point2 = (NXOpen.Point)datumCsys1.FindObject("POINT 1");
sketchInPlaceBuilder1.SketchOrigin = point2;
sketchInPlaceBuilder1.PlaneOrFace.Value = null;
sketchInPlaceBuilder1.PlaneOrFace.Value = datumPlane1;
NXOpen.DatumAxis datumAxis1 = (NXOpen.DatumAxis)workPart.Datums.FindObject("DATUM_CSYS(0) X axis");
sketchInPlaceBuilder1.Axis.Value = datumAxis1;
theSession.Preferences.Sketch.CreateInferredConstraints = true;
theSession.Preferences.Sketch.ContinuousAutoDimensioning = true;
theSession.Preferences.Sketch.DimensionLabel = NXOpen.Preferences.SketchPreferences.DimensionLabelType.Expression;
theSession.Preferences.Sketch.TextSizeFixed = true;
theSession.Preferences.Sketch.FixedTextSize = 3.0;
theSession.Preferences.Sketch.ConstraintSymbolSize = 3.0;
theSession.Preferences.Sketch.DisplayObjectColor = false;
theSession.Preferences.Sketch.DisplayObjectName = true;
NXOpen.NXObject nXObject2;
nXObject2 = sketchInPlaceBuilder1.Commit();
NXOpen.Sketch sketch1 = (NXOpen.Sketch)nXObject2;
NXOpen.Features.Feature feature1;
feature1 = sketch1.Feature;
sketch1.Activate(NXOpen.Sketch.ViewReorient.True);
sketchInPlaceBuilder1.Destroy();
sketchAlongPathBuilder1.Destroy();
try
{
// Expression is still in use.
workPart.Expressions.Delete(expression2);
}
catch (NXException ex)
{
ex.AssertErrorCode(1050029);
}
try
{
// Expression is still in use.
workPart.Expressions.Delete(expression1);
}
catch (NXException ex)
{
ex.AssertErrorCode(1050029);
}
// ----------------------------------------------
// Menu: Insert->Sketch Curve->Line...
// ----------------------------------------------
NXOpen.Point3d startPoint1 = new NXOpen.Point3d(0.0, 0.0, 0.0);
NXOpen.Point3d endPoint1 = new NXOpen.Point3d(0, b, 0.0);
NXOpen.Line line1;
line1 = workPart.Curves.CreateLine(startPoint1, endPoint1);
theSession.ActiveSketch.AddGeometry(line1, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
//
NXOpen.Point3d startPoint2 = new NXOpen.Point3d(0.0, b, 0.0);
NXOpen.Point3d endPoint2 = new NXOpen.Point3d(L, a, 0.0);
NXOpen.Line line2;
line2 = workPart.Curves.CreateLine(startPoint2, endPoint2);
theSession.ActiveSketch.AddGeometry(line2, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
NXOpen.Point3d startPoint3 = new NXOpen.Point3d(L, a, 0.0);
NXOpen.Point3d endPoint3 = new NXOpen.Point3d(L, 0.0, 0.0);
NXOpen.Line line3;
line3 = workPart.Curves.CreateLine(startPoint3, endPoint3);
theSession.ActiveSketch.AddGeometry(line3, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
NXOpen.Point3d startPoint4 = new NXOpen.Point3d(L, 0.0, 0.0);
NXOpen.Point3d endPoint4 = new NXOpen.Point3d(0.0, 0.0, 0.0);
NXOpen.Line line4;
line4 = workPart.Curves.CreateLine(startPoint4, endPoint4);
theSession.ActiveSketch.AddGeometry(line4, NXOpen.Sketch.InferConstraintsOption.InferNoConstraints);
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = false;
theSession.ActiveSketch.Update();
theSession.Preferences.Sketch.AutoDimensionsToArcCenter = true;
// ----------------------------------------------
// Dialog Begin Line
// ----------------------------------------------
// ----------------------------------------------
// Menu: File->Finish Sketch
// ----------------------------------------------
theSession.ActiveSketch.Deactivate(NXOpen.Sketch.ViewReorient.False, NXOpen.Sketch.UpdateLevel.Model);
// ----------------------------------------------
// Menu: Insert->Design Feature->Extrude...
// ----------------------------------------------
NXOpen.Features.Feature nullNXOpen_Features_Feature = null;
if (!workPart.Preferences.Modeling.GetHistoryMode())
{
throw new Exception("Create or edit of a Feature was recorded in History Mode but playback is in History-Free Mode.");
}
NXOpen.Features.ExtrudeBuilder extrudeBuilder1;
extrudeBuilder1 = workPart.Features.CreateExtrudeBuilder(nullNXOpen_Features_Feature);
NXOpen.Section section1;
section1 = workPart.Sections.CreateSection(0.0095, 0.01, 0.5);
extrudeBuilder1.Section = section1;
extrudeBuilder1.AllowSelfIntersectingSection(true);
NXOpen.Unit unit2;
unit2 = extrudeBuilder1.Draft.FrontDraftAngle.Units;
NXOpen.Expression expression7;
expression7 = workPart.Expressions.CreateSystemExpressionWithUnits("2.00", unit2);
extrudeBuilder1.DistanceTolerance = 0.01;
extrudeBuilder1.BooleanOperation.Type = NXOpen.GeometricUtilities.BooleanOperation.BooleanType.Create;
NXOpen.Body[] targetBodies1 = new NXOpen.Body[1];
NXOpen.Body nullNXOpen_Body = null;
targetBodies1[0] = nullNXOpen_Body;
extrudeBuilder1.BooleanOperation.SetTargetBodies(targetBodies1);
extrudeBuilder1.Limits.StartExtend.Value.RightHandSide = "0";
extrudeBuilder1.Limits.EndExtend.Value.RightHandSide = t.ToString();
extrudeBuilder1.Offset.StartOffset.RightHandSide = "0";
extrudeBuilder1.Offset.EndOffset.RightHandSide = "5";
NXOpen.GeometricUtilities.SmartVolumeProfileBuilder smartVolumeProfileBuilder1;
smartVolumeProfileBuilder1 = extrudeBuilder1.SmartVolumeProfile;
smartVolumeProfileBuilder1.OpenProfileSmartVolumeOption = false;
smartVolumeProfileBuilder1.CloseProfileRule = NXOpen.GeometricUtilities.SmartVolumeProfileBuilder.CloseProfileRuleType.Fci;
section1.DistanceTolerance = 0.01;
section1.ChainingTolerance = 0.0095;
section1.SetAllowedEntityTypes(NXOpen.Section.AllowTypes.OnlyCurves);
NXOpen.Features.Feature[] features1 = new NXOpen.Features.Feature[1];
NXOpen.Features.SketchFeature sketchFeature1 = (NXOpen.Features.SketchFeature)feature1;
features1[0] = sketchFeature1;
NXOpen.CurveFeatureRule curveFeatureRule1;
curveFeatureRule1 = workPart.ScRuleFactory.CreateRuleCurveFeature(features1);
section1.AllowSelfIntersection(true);
NXOpen.SelectionIntentRule[] rules1 = new NXOpen.SelectionIntentRule[1];
rules1[0] = curveFeatureRule1;
NXOpen.Point3d helpPoint1 = new NXOpen.Point3d(0.0, 0.0, 0.0);
section1.AddToSection(rules1, null, null, null, helpPoint1, NXOpen.Section.Mode.Create, false);
NXOpen.Direction direction1;
direction1 = workPart.Directions.CreateDirection(sketch1, NXOpen.Sense.Forward, NXOpen.SmartObject.UpdateOption.WithinModeling);
extrudeBuilder1.Direction = direction1;
extrudeBuilder1.ParentFeatureInternal = false;
NXOpen.Features.Feature feature2;
feature2 = extrudeBuilder1.CommitFeature();
NXOpen.Expression expression8 = extrudeBuilder1.Limits.StartExtend.Value;
NXOpen.Expression expression9 = extrudeBuilder1.Limits.EndExtend.Value;
extrudeBuilder1.Destroy();
workPart.Expressions.Delete(expression7);
// ----------------------------------------------
// Menu: Tools->Journal->Stop Recording
// ----------------------------------------------
// ----------------------------------------------
// Menu: File->Export->IGES...
// ----------------------------------------------
NXOpen.IgesCreator igesCreator1;
igesCreator1 = theSession.DexManager.CreateIgesCreator();
igesCreator1.ExportModelData = true;
igesCreator1.ExportDrawings = true;
igesCreator1.MapTabCylToBSurf = true;
igesCreator1.BcurveTol = 0.0508;
igesCreator1.IdenticalPointResolution = 0.001;
igesCreator1.MaxThreeDMdlSpace = 10000.0;
igesCreator1.ObjectTypes.Curves = true;
igesCreator1.ObjectTypes.Surfaces = true;
igesCreator1.ObjectTypes.Annotations = true;
igesCreator1.ObjectTypes.Structures = true;
igesCreator1.ObjectTypes.Solids = true;
igesCreator1.SettingsFile = "C:\\Program Files\\Siemens\\NX 10.0\\iges\\igesexport.def";
igesCreator1.MaxLineThickness = 2.0;
igesCreator1.SysDefmaxThreeDMdlSpace = true;
igesCreator1.SysDefidenticalPointResolution = true;
igesCreator1.InputFile = "J:\\ME 578 Systems\\Midterm\\MidtermProject\\GoldBeam.igs";
igesCreator1.OutputFile = "J:\\ME 578 Systems\\Midterm\\MidtermProject\\GoldBeam.igs";
igesCreator1.FileSaveFlag = false;
igesCreator1.LayerMask = "1-256";
igesCreator1.DrawingList = "";
NXOpen.TaggedObject[] objects1 = new NXOpen.TaggedObject[0];
igesCreator1.SetDrawingArray(objects1);
NXOpen.NXObject nXObject20;
nXObject20 = igesCreator1.Commit();
igesCreator1.Destroy();
while (!System.IO.File.Exists("J:\\ME 578 Systems\\Midterm\\MidtermProject\\GoldBeam.igs"))
{
System.Threading.Thread.Sleep(10);
}
}
