private void Form1_FormClosing(object sender, FormClosingEventArgs e)
{
if (E1803 != null)
{
E1803.close();
E1803 = null;
}
}
private void Form1_Load(object sender, EventArgs e)
{
E1803 = new DotNet1803();
if (E1803.set_connection("192.168.2.254"))
{
// E1803.set_password("123456"); // used only in case of Ethernet connection; requires the password "123456" to be set in card configuration file
if (E1803.load_correction("", 0)) // set correction file, for no/neutral correction use "" or NULL here
{
E1803.set_laser_mode(DotNet1803.lasermode.LASERMODE_CO2); // configure for CO2
E1803.set_standby(20000.0, 5.0); // 20kHz and 5 usec standby frequency/period
E1803.set_laser_timing(20000.0, 25.0); // 20kHz and 50% duty cycle marking frequency/period
}
else
{
MessageBox.Show("ERROR: opening connection failed with error " + E1803.ErrorDetail);
E1803 = null;
}
}
else
{
MessageBox.Show("ERROR: Could not initialise!");
E1803 = null;
}
}
static void Main(string[] args)
{
DotNet1803 E1803 = new DotNet1803();
if (E1803.set_connection("192.168.2.254"))
{
// E1803.set_password("123456"); // used only in case of Ethernet connection; requires the password "123456" to be set in card configuration file
if (E1803.load_correction("", 0)) // set correction file, for no/neutral correction use "" or NULL here
{
E1803.set_laser_mode(DotNet1803.lasermode.LASERMODE_CO2); // configure for CO2
E1803.set_standby(20000.0, 5.0); // 20kHz and 5 usec standby frequency/period
E1803.set_laser_timing(20000.0, 25.0); // 20kHz and 50% duty cycle marking frequency/period
// perform a normal mark operation
E1803.set_laser_mode(DotNet1803.lasermode.LASERMODE_CO2); // configure for CO2
E1803.set_standby(20000.0, 5.0); // 20kHz and 5 usec standby frequency/period
E1803.set_laser_timing(20000.0, 25.0); // 20kHz and 50% duty cycle marking frequency/period
E1803.set_scanner_delays(100.0, 100.0, 10.0); // some delay values, have to be adjusted for used scanhead
E1803.set_laser_delays(20.0, 30.0); // laser on/off delay in microseconds, have to be adjusted for used scan-system
E1803.set_speeds(67108864.0, 67108.864); // speeds in bits per milliseconds within an 26 bit range, here jump speed is 1000 times faster than mark speed
E1803.digi_set_motf(0.0, 0.0); // no marking on-the-fly enabled
E1803.set_trigger_point(); // wait for external trigger
E1803.jump_abs(-10000000, -10000000, 0); // jump to mark start position (using unit bits within an 26 bit range)
E1803.mark_abs(-10000000, 10000000, 0); // mark a square
E1803.mark_abs(10000000, 10000000, 0); // mark a square
E1803.mark_abs(10000000, -10000000, 0); // mark a square
E1803.mark_abs(-10000000, -10000000, 0); // mark a square
E1803.execute();
// wait until marking has started
while ((E1803.get_card_state() & (E1803.CSTATE_MARKING | E1803.CSTATE_PROCESSING)) == 0)
{
Thread.Sleep(10);
}
E1803.release_trigger_point(); // release waiting for external trigger by software command
// wait until marking is finished
while ((E1803.get_card_state() & (E1803.CSTATE_MARKING | E1803.CSTATE_PROCESSING)) != 0)
{
Thread.Sleep(500);
}
E1803.close();
}
else
{
Console.WriteLine("ERROR: opening connection failed with error " + E1803.ErrorDetail);
}
}
else
{
Console.WriteLine("ERROR: Could not initialise!");
}
}
